1991 LEXUS SC400 length

35. INSTALL HEATER WATER VALVE(a) Install the water valve and bracket assembly with thetwo bolts.
(b) Install the engine wire clamp with the bolt.
(c) Connect the VSV connector.
36. INSTALL ISC VALVE (a) Install a new gasket and the ISC valve with the two nuts.
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
(b) Connect the water by±pass hose (from throttle body) to
the ISC valve.
(c) Connect the ISC valve connector.
37. INSTALL EGR VALVE ADAPTOR (a) Install a new gasket, the adaptor and connector bracket(USA spec. only) with the two bolts and two nuts.
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
HINT: Use bolts 20 mm (1.79 in.) in length.
NOTICE: Do not touch the air intake chamber and adap-
tor surfaces of the gasket with your hand.
(b) Connect the PCV hose to cylinder head.
(c) (USA Spec. only)
Connect the EGR gas temperature sensor connector.
EM±110
±
ENGINE MECHANICAL Cylinder Heads
WhereEverybodyKnowsYourName

41. INSTALL TIMING BELT REAR PLATESInstall the rear plate with the two bolts. Install the two rear
plates.
Torque: 7.8 N Vm (80 kgf Vcm, 69 in. Vlbf)
42. INSTALL WATER INLET AND INLET HOUSING
(a) Remove any old packing (FIPG) material.w Using a razor blade and gasket scraper, remove all
the old packing (FIPG) materials from the gasket
surfaces and sealing groove.
w Thoroughly clean all components to remove all the
loose materials.
w Using a non±residue solvent, clean both sealing
surfaces.
(b) Apply seal packing to the sealing groove of the water inlet housing as shown in the illustration.
Seal packing: Part No.08826±00100 or equivalent
w Install a nozzle that has been cut to a 2±3 mm
(0.08±0.12 in.) opening.
w Parts must be assembled within 5 minutes of
application. Otherwise the material must be
removed and reapplied.
w Immediately remove nozzle from the tube and
reinstall cap.
(c) Install a new O±ring to the water inlet housing.
(d) Apply soapy water to the O±ring.
(e) Push the water inlet housing end into the water pump hole.
(f) Install the water inlet and housing assembly with the two
bolts. Alternately tighten the bolts.
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
HINT: Use bolts 25 mm (0.98 in.) in length.
(g) Connect the water by±pass hose to the ISC valve.
±
ENGINE MECHANICAL Cylinder HeadsEM±113
WhereEverybodyKnowsYourName

6. INSPECT MAIN BEARING CAP STUD BOLTSUsing a vernier caliper, measure the tension portion diameter
of the stud bolt.
Standard diameter: 7.500±7.600 mm
(0.2953±0.2992 in.)
Minimum diameter: 7.40 mm (0.2913 in.)
If the diameter is less than minimum, replace the stud bolt.
7. IF NECESSARY, REPLACE MAIN BEARING CAP STUD BOLTS
(a) Using the two main bearing cap nuts, remove the studbolt.
(b) Apply a light coat of engine oil on the threads and under
the flange of the stud bolt.
(c) Using the two main bearing cap nuts, install and torque
the stud bolt.
Torque: 10 N Vm (100 kgf Vcm, 7 ft Vlbf)
HINT: Stud bolts come in lengths of 90.0 mm (3.543 in.) and
101.5 mm (3.996 in.). Install the 101.5 mm (3.996 in.) bolts
in inside positions. Install the 90.0 mm (3.543 in.) bolts in out-
side positions.
DISASSEMBLY OF PISTON AND
CONNECTING ROD ASSEMBLIES
1. CHECK FIT BETWEEN PISTON AND PISTON PIN
Try to move the piston back and forth on the piston pin.
If any movement is felt, replace the piston and pin as a set.
EM±144
±
ENGINE MECHANICAL Cylinder Block
WhereEverybodyKnowsYourName

(c) Place a new O±ring in position on the cylinder block.
(d) Engage the spline teeth of the oil pump drive gear withthe large teeth of the crankshaft, and slide the oil pump.
(e) Install the oil pump with the eight bolts.
Torque: 12 mm head 16 N Vm (160 kgf Vcm, 12 ft Vlbf)
14 mm head 30 N Vm (310 kgf Vcm, 22 ft Vlbf)
HINT: Each bolt length is indicated in the illustration.
Bolt length:
A 50 mm (1.97 in.) for 12 mm head
B 106 mm (4.17 in.) for 12 mm head
C 30 mm (1.18 in.) for 12 mm head
D 40 mm (1.57 in.) for 14 mm head
4. INSTALL NO. 1 OIL PAN AND NO. 2 OIL PANS (See steps 4 to 9 on pages LU±16 to 19)
5. INSTALL WATER PUMP (a) Remove any old packing (FIPG) material and be carefulnot to drop any oil on the contact surfaces of the water
pump and cylinder block.
w Using a razor blade and gasket scraper, remove all
the old packing (FIPG) material from the gasket
surfaces and sealing groove.
w Thoroughly clean all components to remove all the
loose material.
w Using a non±residue solvent, clean both sealing
surfaces.
EM±162
±
ENGINE MECHANICAL Cylinder Block
WhereEverybodyKnowsYourName

(b) Apply seal packing to the sealing groove of the waterpump as shown in the illustration.
Seal packing: Part No.08826±00100 or equivalent
wInstall a nozzle that has been cut to a 2±3 mm
(0.08±0.12 in.) opening.
w Parts must be assembled within 5 minutes of
application. Otherwise the material must be removed
and reapplied.
w Immediately remove nozzle from the tube and reinstall
cap.
(c) Install the water pump with the five bolts, two stud bolts and nut.
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
HINT: Use bolts 30 mm (1.18 in.) in length.
6. INSTALL ENGINE WIRE (a) Install the engine wire to the LH side of the cylinder block
with the two bolts.
(b) Install the wire cover with the three bolts.
(c) Connect the following connectors: (1) Oil level sensor connector
(2) Oil pressure switch connector
7. INSTALL WATER BY±PASS PIPE (a) Install a new O±ring to the by±pass pipe.
(b) Apply soapy water to the O±ring.
(c) Pull in the by±pass pipe end into the pipe hole of thewater pump.
(d) Install the water by±pass pipe with the two bolts.
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
±
ENGINE MECHANICAL Cylinder BlockEM±163
WhereEverybodyKnowsYourName

SERVICE SPECIFICATIONS
SERVICE DATA
 Engine tune±up Battery specific gravity  1.27±1.29 g  (when fully charged at 205C (68 5F))  High±tension cord resistance Limit 25 k
per cord  Valve clearance Intake 0.15 ± 0.25 mm 0.006 ± 0.010 in.   Exhaust 0.25 ± 0.35 mm 0.010 ± 0.014 in.
  Ignition timing 8±12 5 BTDC @ idle
   (w/ Terminals TE1 and E1 connected)
  Idle speed 700 + 50 rpm
 


Intake
manifold 


at Idle speed 


 


60 kPa 450 mmHg 17.7 in.Hg
vacuum vacuum  
Compressionat 250 rpmSTD1,226 kPa (12.5 kgf/cm, 178 psi) or more pressure  Limit 981 kPa 10.0 kgf/cm 142 psi  Difference of pressure between each cylinder 98 kPa (1.0 kgf/cm, 14 psi) or less Timing belt ten- Protrusion from housing end 10.5 ± 11.5 mm 0.413 ± 0.453 in. g
sioner g  
 Cylinder head Warpage Cylinder block side Limit 0.10 mm 0.0039 in.
 
y
 Manifold side Limit 0.10 mm 0.0039 in.
  Valve seat Refacing angle 30
5, 45 5, 75 5
  Contacting angle 455
Contacting width1.0 ± 1.4 mm0.039 ± 0.055 in.  Cylinder head bolt thread outside diam4eter 
   STD 9.770 ± 9.960 mm 0.3846 ± 0.3921 in.   Limit 9.60 mm 0.3780 in. Valve guide Inside diameter 6.010 ± 6.030 mm 0.2366 ± 0.2374 in.
 
g
bushing Outside diameter (for repair part) STD 11.048 ± 11.059 mm 0.4350 ± 0.4354 in.
 
g
  O/S 0.05 11.098 ± 11.109 mm 0.4369 ± 0.4374 in.
 Valve Valve overall length STD Intake 94.95 mm 3.7382 in.
    Exhaust 96.90 mm 3.8150 in.
LimitIntake94.45 mm3.7185 in.    Exhaust 96.40 mm 3.7953 in.  Valve face angle   44.5 5  Stem diameter  Intake 5.970 ± 5.985 mm 0.2350 ± 0.2356 in.    Exhaust 5.965 ± 5.980 mm 0.2356 ± 0.2354 in.
  Stem oil clearance STD Intake 0.025 ± 0.060 mm 0.0010 ± 0.0024 in.
    Exhaust 0.030 ± 0.065 mm 0.0012 ± 0.0026 in.
   Limit Intake 0.08 mm 0.0031 in.
Exhaust0.10 mm0.0039 in.  Margin thickness  STD 1.0 mm 0.039 in.    Limit 0.5 mm 0.020 in. Valve spring Squareness Limit 2.0 mm 0.079 in. g Free length  43.6 mm 1.717 in.
  Installed tension at 32.9 mm (1.295 in.) 186±206 N 
    (19.0 ± 21.0 kgf, 41.9 ± 46.3 lbf)
 Valve lifter Lifter diameter 30.966±30.976 mm 1.2191±1.2195 in.
  Lifter bore diameter  31.000±31.016 mm 1.2205±1.2211 in.
Oil clearanceSTD0.024±0.050 mm0.0009±0.0020 in.   Limit 0.07 mm 0.0028 in.
EM±178±
ENGINE MECHANICAL Service Specifications
WhereEverybodyKnowsYourName

(b) Temporarily install a new gasket and the EGR pipe to air
intake chamber with the two bolt.
(c) (Exc. USA Spec.) Install the connector bracket to check (ºDIAGNOSISº)
connector.
(d) Install the air intake chamber and following parts with the four bolts and eight nuts:
(1) Check (ºDIAGNOSISº) connector
(2) A/T throttle cable bracket
(3) VSV for fuel pressure control system
(4) VSV for EGR system
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
HINT: Use bolts 40 mm (1.57 in.) of length.
(e) Tighten the bolt holding the EGR pipe to the air intake
chamber.
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
(f) Connect the cold start injector tube to the RH delivery
pipe with two new gaskets and union bolt.
Torque: 15 N Vm (150 kgf Vcm, 11 ft Vlbf)
FI±36EFI SYSTEM ± Fuel System (Cold Start Injector)
WhereEverybodyKnowsYourName

4. CONNECT CONNECTORSConnect the following connectors:w Cold start injector connector
w ISC valve connector
w (USA Spec.)
EGR valve connector
w (Exc. USA Spec.)
VSV connector for EGR system
w SV connector for fuel pressure control system
5. INSTALL THROTTLE BODY (a) Connect the following hoses:(1) PCV hose to throttle body
(2) Water by±pass hose to throttle body
(b) Install a new gasket and throttle body with the two bolts and two nuts.
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
HINT: Use bolts 40 mm (1.57 in.) in length.
(c) Install the water by±pass pipe (from rear water bypass
joint) to the clamp on the engine wire cover.
(d) Connect the following hoses: (1) Water by±pass hose to the ISC valve
(2) (USA Spec.) Vacuum hose to throttle body
(3) (Exc. USA Spec.) Three vacuum hoses to throttle body
FI±38
EFI SYSTEM
± Fuel System (Cold Start Injector)
WhereEverybodyKnowsYourName