1991 LEXUS SC400 fuse

TROUBLESHOOTING
Turn Signal and Hazard Warning Light
System
You will find the cause of trouble more easily using the table shown below. In this table, the numbers indicate
the order priority of the causes in trouble. Check each part in the order \
shown. If necessary, replace the parts.
See pagePart
name
Trouble
ªHazardº and ªTurnº do not light up.
The flashing frequency is abnormal.
Hazard warning light does not light up.
(Turn is normal.)
Hazard warning light does not light up
in one direction.
*  Turn signal does not light up.
*

Turn signal does not light up.
Turn signal does not light up in one direction.
Only one bulb does not light up.
*
: Combination Meter, Wiper and Washer do not operate.
*  : Combination Meter, Wiper and Washer are normal.
HAZ±HORN Fuse
TURN Fuse
Ignition Switch
Hazard Warning Switch
Turn Signal Flasher
Turn Signal Switch
Wire Harness
Bulb
BE±4
, 21
BE±4
, 20
BE±26
BE±68
BE±68
BE±46
BE±6
BE±70±
BODY ELECTRICAL SYSTEM Lighting System
WhereEverybodyKnowsYourName

TROUBLESHOOTING
Interior Light System
You will find the cause of trouble more easily using the table shown below. In this table, the numbers indicate
the order priority of the causes in the trouble. Check each part in the ord\
er shown. If necessary, replace the parts.
See pageB±4,21BE±79BE±49BE±80BE±81BE±82
±
BE±6
Trouble
Part Name
DOME FuseDoor Courtesy SwitchIntegration RelayFront Personal LightVanity LightLuggage Compartment Door
Courtesy SwitchWire HarnessBulb
Only one interior light does not light up.21
Interior light does not light up. (All)12
ºIlluminated Entry Systemº does not oper-
ate.213
Interior light does not light up.
(in front personal light)231
Front personal light does not light up.231
Rear personal light does not light up.21
Vanity light does not light up.231
Luggage compartment light does not light
up.231
Courtesy light does not light up.231
±
BODY ELECTRICAL SYSTEM Lighting SystemBE±83
WhereEverybodyKnowsYourName

TROUBLESHOOTING
You will find the cause of trouble more easily by properly using the table \
shown below. In this table, the num-
bers indicate the order priority of causes of trouble. Check each part in th\
e order shown. If necessary, re-
place the parts.
See pageB±4,21BE±26BE±4,20BE±91BE±90BE±92BE±91BE±93±
Trouble
Part Name
AM1 FuseIgnition SwitchWIPER FuseWiper SwitchWiper MotorWasher MotorWasher SwitchWasher Hose and NozzleWire Harness
Wipers and washers do not operate.*1132456
Wipers and washers do not operate.*221345
Wipers and washers do not operate.*31234
Wipers do not operate in LO, HI or MIST.123
Wipers do not operate in INT.123
Washer motor does not operate.213
Wipers do not operate when washer switch
is ON.12
Washer fluid does not spray.1
*1: Door Lock and Power Windows do not operate
*
2: Door Lock and Power Window are normal. Combination Meter and Turn Signal do not operate.
*
3: Combination Meter and Turn Signal are normal.
BE±94
±
BODY ELECTRICAL SYSTEM Wiper and Washer System
WhereEverybodyKnowsYourName

DESCRIPTION
The combination meter has various meters and gauges which show the vehicle'\
s condition, warning lights which
monitor abnormalities in the vehicle and inform the driver, indicator lights which inform the driver of the condition
of each part of vehicle, and a function for illumination and brightness ad\
justment of meters and gauges.
The component parts of this system and their functions are described in \
the following table.
Parts NameFunction
SpeedometerThe speedometer needle moves in accordance with signals from the speed s\
ensor to
indicate the vehicle's speed.
TachometerThe tachometer needle moves in accordance with signals from the igniter \
to indicate the
engine's speed.
Water Temperatrue
GaugeThe water temperature gauge's needle moves in accordance with signals from the send-
er gauge and indicates the temperature of the engine coolant.
Fuel GaugeThe fuel gauge needle moves in accordance with signals from the sender g\
auge, indicat-
ing the amount of fuel remaining in the fuel tank.
OdometerThe odometer counts the total distance traveled by the vehicle in accord\
ance with pulse
signals from the speed sensor.
Twin Trip Switch
The twin trip meter counts the distance traveled by the vehicle in accor\
dance with pulse
signals from the speed sensor. It can be reset using a switch and can be used to switch
between trip meters A and B.
Circuit Plate
This plate contains the circuitry for each meter and gauge and for each \
warning light and
indicator light, as well as an internal engine oil level warning drive c\
ircuit, drive circuits for
the odometer and trip meter and brightness adjustment circuitry for each\
indicator.
Speed SensorMounted in the transmission, this sensor outputs pulse signals to the co\
mbination meter
in accordance with the speed of the output shaft.
Twin Trip SwitchOperation of this switch switches between the A and B trip meters and se\
nds reset sig-
nals to the combination meter.
Water
Temperature Sender
GaugeThis sender converts engine coolant temperatures to a resistance value i\
n signal form to
the combination meter.
Fuel Sender GaugeThis sender converts the level of fuel remaining in fuel tank to resista\
nce value and
sends the resistance value in signal form to combination meter.
Rheostat Light
Control VolumeIn order to adjust the degree of illumination of the combination meter, the resistance val-
ue of the built±in variable resistor is sent to the combination meter\
and rheostat light
control.
Fuel Level Warning
SwitchWhen the level of fuel remaining falls below a predetermined level, cont\
inuity is estab-
lished with this switch, which is built into the fuel sender gauge, caus\
ing a warning light
to light up.
Low Oil Pressure
Warning SwitchThis switch is mounted on the engine block. Continuity is established in\
this switch when
the oil pressure is low, causing a warning light to light up.
Integration Relay (Seat
Belt Warning Relay)
This relay receives current from fuse GAUGE and DOME and is connected to\
each
buckle switch, door courtesy switch, key unlock warning switch and warni\
ng light. As
part of the seat belt warning system, it sounds a chime and lights a war\
ning light when
seat belts are unfastened. As part of the key unlock warning system, it \
sounds a chime
when the set conditions are fulfilled.
Light Failure SensorThis sensor senses when a bulb in rear combination light is burnt out an\
d lights up a
warning light.
BE±96±
BODY ELECTRICAL SYSTEM Combination Meter
WhereEverybodyKnowsYourName

ConnectionCheck forTester connectionConditionSpecified value
A19 A15Trip switch A/BPushContinuity
Trip switchContinuity
A19±A15Trip switch A/BFreeNo continuityTrip switchContinuity
A20 A15Trip switch RESETPushContinuityA20±A15Trip switch RESETFreeNo continuity
DOME
FuseVoltageA11±GroundConstantBattery positive voltage
Speed
SVoltageA13 A15
Ignition
switch
*3 Revolve propeller shaft0V
11 V
SensorVoltageA13±A15switch
ON*3 Stop propeller shaft0V or 11V
C1±GroundPBattery positive voltage
C2±GroundIgnitionRBattery positive voltage
Neutral start
it hVoltageC3±Ground
Ignition
switch
ON andNBattery positive voltageswitchVoltageC4±GroundON and
shift leverDBattery positive voltage
C5±Ground
shift lever
position2Battery positive voltage
C16±Ground
osition
LBattery positive voltage
O/D OFFContinuityC18 GroundO/D OFF switchONContinuity
SwitchContinuityC18±GroundO/D OFF switchOFFNo continuity
AlternatorContinuityC15±GroundEngine stopContinuity
ºLº terminalVoltageC14±GroundEngine runningBattery positive voltage
FuelContinuityA7 GroundFuel remainderFullNo continuity
SenderContinuityA7±GroundFuel remainderEmptyContinuity
GaugeFull, Approx. 79.3 mm
(3.12 in.)Approx. 6

ResistanceA8±C8Float
position1/2, Approx. 193.1 mm
(76.0 in.)Approx. 32.5

Empty, Approx. 308.1 mm
(12.13 in.)Approx. 97

*Window
washer level
ContinuityB9±GroundON (float down)Continuitywasher level
warning
switchContinuityB9 Ground
(Canada)OFF (float up)No continuity
Brake fluidBrake fluid levelON (float down)Continuity
Level warning
Brake fluid level
warning SWOFF (float up)No continuity
SW and
Parking brake
SW
ContinuityC13±GroundParking brake
ON (Depress the Ped-
al))Continuity
SWParking brake
SWOFF (Release the Ped-
al)No continuity
Low oil
PressureContinuityC19 GroundEngine condition
RunningNo continuity
Pressure
Warning SWContinuityC19±GroundEngine conditionStopContinuity
Door courtesyContinuityC12 GroundDriver's andOpen (ON)Continuityy
SwitchContinuityC12±GroundDriver s and
passenger's doorClosed (OFF)No continuity
IGN fuseVoltageC14 GroundIgnition switchONBattery positive voltageVoltageC14±GroundIgnition switchLOCK or ACCNo voltage
CIG fuseVoltageA6 GroundIgnition switchACC or ONBattery positive voltageVoltageA6±GroundIgnition switchLOCK or STARTNo voltage
BE±107±
BODY ELECTRICAL SYSTEM Combination Meter
WhereEverybodyKnowsYourName

ConnectionCheck forTester connectionConditionSpecified value
Turn signalHazard warning switch ONBattery positiveTurn signal
SW andB 16 Ground
Hazard warning switch ONBattery ositive
voltage e 0V
HazardB±16±Ground
IG SW ON and turn signal SW ºLeftºBattery positive
Warning
Si hVoltage
IG SW ON and turn signal SW ºLeftºBattery ositive
voltage e 0V
SwitchVoltage
Hazard warning switch ONBattery positive
B 17 Ground
Hazard warning switch ONBattery ositive
voltage e 0VB±17±Ground
IG SW ON and turn signal SW ºRightºBattery positiveIG SW ON and turn signal SW ºRightºBattery ositive
voltage e 0V
HeadlightLi ht t l SWDimmer SW ºHIº orBattery positiveHeadlight
VoltageB7±GroundLight control SW
ºHEADº
Dimmer SW HI or
ºFlashº
Battery ositive
voltageVoltageB7±GroundºHEADºDimmer SW ºLOºNo voltage
ContinuityB6±GroundLight control SW
º
HEADº
Dimmer SW ºHIº or
ºFlashºContinuityContinuityB6 GroundºHEADºDimmer SW ºLOºNo continuity
IgniterVoltageA9±GroundEngine RunningVoltage
fluctuates
ECT patternVoltageB4 GroundIG SW ON and ECT patternPWRBattery positive voltageECT attern
Select switchVoltageB4±GroundIG SW ON and ECT attern
select SW positionNORMNo voltage
Engine oilOil temperature below approx. 55 5C (131 5F)Continuityg
Level warn-
ing Switch
ContinuityB8±Ground
Oil temperature
above approx. 55 5CON (float up)ContinuitygContinuityB8 Groundabove a rox. 55 C
(131 5F) and SW
positionOFF (float off)No continuity
GAUGE fuseVoltageA1 GroundIgnition switchONBattery positive voltageVoltageA1±GroundIgnition switch
positionLOCK, ACC, STARTNo voltage
Neutral StartVoltageA12±GroundIgnition switch
position
START (ºPº or ºNº
range)Battery positive voltage
switch
VoltageA12 GroundpositionLOCK, ACC, ONNo voltage
ECU±BVoltageC11 GroundIgnition switchONBattery positive voltage
FuseVoltageC11±GroundIgnition switch
positionLOCK, ACC, STARTNo voltage
Rheostat
Li ht t l
ON (Rheostat knob
t d itiBtt ltLight control
VolumeLight control SWturned any position
except fully clock-
Battery voltage or
5V or moreVolume
VoltageA2±Ground
g
HEAD or TAIL and
rheostat volume
except fully clock-
wise)5V or more
VoltageA2 Groundrheostat volume
knob positionOFF (Rheostat knob)
turned fully clockNo voltageknob ositionturned fully clock-
wise)No voltage
GroundA8±GroundConstantContinuity
ContinuityA10±GroundConstantContinuityContinuityA22±GroundConstantContinuity
A23±GroundConstantContinuity
*1 Jack up the vehicle.*2 Shift lever position is ºPº range.
If circuit is not as specified, refer to BE±100 wiring diagrams
and inspect the circuits connected to other parts.
BE±108
±
BODY ELECTRICAL SYSTEM Combination Meter
WhereEverybodyKnowsYourName

DIAGNOSTIC TROUBLE CODE
CLEARANCE
1. Using SST, connect terminals Tc and E1 of DLC2 or DLC1.SST 09843±18020
2. IG switch ON.
3. Clear the diagnostic trouble codes stored in ECU by depressing the brake pedal 8 or more times within 3 seconds.
4. Check that the TRAC indicator light shows the normal code.
5. Remove the SST from the terminals of DLC2 or DLC1.
HINT: Cancellation can also be done by removing the DOME
fuse, but in this case, other memory systems will also be can-
celled out.
±
BRAKE SYSTEM TRACTION CONTROL SYSTEM (TRAC)BR±171
WhereEverybodyKnowsYourName

WIRING DIAGRAM
IN±33).
DTC24TRAC Sub±Throttle Actuator Circuit
CIRCUIT DESCRIPTION
The sub±throttle actuator operates in accordance with signals from the E\
CU, controlling the opening and
closing of the sub±throttle valve.
DTC No.DTC Detecting ConditionTrouble Area
24Open or short in sub±throttle actuator circuit

TRAC fuse

Open or short in BM circuit.

Sub±throttle actuator.

Open or short in sub±throttle actuatorcircuit.

ECU
DIAGNOSTIC CHARTDIAGNOSTIC CHART
BR±186±
BRAKE SYSTEM TRACTION CONTROL SYSTEM (TRAC)
WhereEverybodyKnowsYourName