1986 TOYOTA CAMRY V20 ac relay

Light Control Rheostat
TAIL Fuse
IGN Fuse
Water Temperature Sender Gauge
Ground
Seat Belt Warning Relay
Brake Fluid Level Warning Switch and Parking
Brake Switch
CHARGE Fuse
TCCS ECU ,
A. B. S. ECU
Cruise Control ECU and ECT ECU
Ground
Fuel Sender Gauge Terminal 3
Fuel Sender Gauge Terminal 2
. GAUGE Fuse
DOME Fuse
Door Courtesy Switch
Low Oil Pressure Switch
Light Failure Sensor
Turn Signal Switch Terminal 28
Ground
Turn Signal Switch Terminal 25
Turn Signal Switch Terminal 23 (USA)
HEAD±HI (RH) Fuse (CANADA)
A/T Oil Temperature Switch
Igniter
Combination Meter and Gauges
(w/ Tachometer)
COMBINATION METER CIRCUIT
Wiring Connector Side
No.
± BODY ELECTRICAL SYSTEMCombination MeterBE±33

Seat Belt Warning
INSPECTION OF SEAT BELT WARNING
1. INSPECT WARNING LIGHT OPERATION
(a) Disconnect the connector from the seat belt warning
relay and ground the terminal 5 on the wire harness
side.
(b) Turn the ignition switch ON, check that the warning
light lights.
If warning light does not light, test the bulb.
2. INSPECT BUCKLE SWITCH OPERATION
(a) Disconnect the connector from the switch.
(b) Check that there is no continuity between terminals
on the switch side connector with the belt fastened.
(c) Check that there is continuity between terminals on
the switch side connector with the belt unfastened.
If operation is not as specified, replace the seat belt inner.
3. INSPECT UNLOCK WARNING SWITCH OPERATION
(See page BE±1 3)
If operation is not as specified, replace the switch.
4. INSPECT SEAT BELT WARNING RELAY CIRCUIT
Disconnect the relay connector and inspect the connector
on the wire harness side as shown in the chart.
Unlock warning switch OFF (Ignition key removed)
If circuit is as specified, replace the relay.
Unlock warning switch ON (Ignition key set)
Buckle switch ON (Seat belt unfastened)Buckle switch OFF (Seat belt fastened)Courtesy switch ON (Door opened)
Turn ignition switch to OFF or ACCTurn ignition switch to OFF or ACC Courtesy switch OFF (Door closed)
Turn ignition switch ONTurn ignition switch ON
6 ± Ground
Tester
connectionSpecified value
Battery voltage
Battery voltage
Battery voltageBattery voltage
No continuity 1 ± Ground
2 ± Ground
3 ± Ground
5 ± Ground4 ± GroundContinuity
Continuity
ContinuityNo voltageNo voltageNo voltage
No voltage
Continuity Condition
Check for
VoltageVoltage
Always
± BODY ELECTRICAL SYSTEMCombination MeterBE±41

Rear Window Defogger Switch
INSPECTION OF SWITCH
INSPECT SWITCH OPERATION
(a) Connect the positive (+) lead from the battery to
terminal 2 and the negative (±) lead to terminal 3.
(b) Connect terminals 2 and 6 through a 3.4 W test bulb.
(e) Push the defogger switch. Check that the test bulb
lights for 12 to 18 minutes, then the test bulb goes
out.
If operation is not as specified, replace the switch.
Rear Window Defogger Relay
INSPECTION OF RELAY
1. INSPECT RELAY CONTINUITY
(a) Check that there is continuity between terminals 1
and 3.
(b) Check that there is no continuity between terminals 2
and 4.
(e) Check that there is no continuity between terminals 3
and 4.
If continuity is not as specified, replace the relay.
Reset breaker and check for short
Replace fuse and check for short
Check switch
Check relay
Check wires
Repair as necessary
REAR WINDOW DEFOGGER
Troubleshooting
Circuit breaker OFF
GAUGE fuse blown
Defogger switch faulty
Defogger relay faulty
Defogger wire broken
Wiring and ground faulty Rear window defogger
does not work.BE±3
BE±3
BE±42
BE±42
BE±43 Possible cause Problem
Remedy
Page
± BODY ELECTRICAL SYSTEMRear Window DefoggerBE±42

Rear Window Defogger Wires
CAUTION:
wWhen cleaning the glass, use a soft, dry cloth, and
wipe the glass in the direction of the wire. Take care
not to damage the wires.
wDo not use detergents or glass cleaners with abra-
sive ingredients.
wWhen measuring voltage, wind a piece of tin foil
around the top of the negative probe and press the
foil against the wire with your finger as shown.
INSPECTION OF DEFOGGER WIRES
1. INSPECT FOR WIRE BREAKAGE
(a) Turn the ignition switch to ON.
(b) Turn the defogger switch to ON.
HINT: If there are 10V, the wire is broken between the cen-
ter of the wire and positive (+) end. If there is no voltage,
the wire is broken between the center of the wire and
ground.
2. INSPECT FOR WIRE BREAKAGE POINT
(a) Place the voltmeter positive (+) lead against the de-
fogger positive (+) terminal.
(b) Place the voltmeter negative (±) lead with the foil strip
against the heat wire at the positive (+) terminal end
and slide it toward the negative (±) terminal end.
(c) The point where the voltmeter deflects from zero to
several volts is the place where the heat wire is bro-
ken.
HINT: If the heat wire is not broken, the voltmeter will ind
cafe 0V at the positive (+) end of the heat wire but gradua
ly increase to about 12V as the meter prove is moved to
the other end. 2. INSPECT RELAY OPERATION
(a) Apply battery voltage to terminals 1 and 3.
(b) Check that there is continuity between terminals 2
and 4.
(c) Check that there is no continu,ity between terminals
3 and 4.
If operation is not as specified, replace the relay.
(c) Inspect the voltage at the center of each heat wire as
shown.
Okay (No break in wire)
Approx. 1 OV or OVApprrox. 5V
Broken wire Voltage
Criteria
± BODY ELECTRICAL SYSTEMRear Window DefoggerBE±43

Heater Control Assembly
Connector ºAº
Air Vent Mode Control
Servo Motor RECIRC/FRESH
Control Servo MotorAmplifier
Connector ºAº
Connectors
Air Mix Control Servo Motor
Blower Speed
Control RelayBlower Resistor Connector º6º
Connectorº6º
Blower MotorHeater Relay
± BODY ELECTRICAL SYSTEMHeaterBE±46

Heater Blower Switch
(Lever Type)
INSPECTION OF SWITCH
INSPECT SWITCH CONTINUITY
Inspect the heater blower switch continuity.
Control cables broken or binding
Servo motor faulty
Heater hoses leaking or clogged
Water valve faulty
Air dampers broken
Air ducts clogged
Heater radiator leaking or clogged
Heater control unit faulty Heater circuit breaker OFF
GAUGE fuse blown
Heater relay faulty
Blower speed control relay faulty
Heater blower switch faulty
Heater blower resistor faulty
Heater blower motor faulty wiring or
ground faultyReset breaker and check for short
Replace fuse and check for short
Check relay
Check control relay
Check switch
Check resistor
Check motor
Repair as necessary
Check cables
Check servo motor
Replace hoses
Replace water valve
Repair air dampers
Repair air ducts
Repair heater radiator
Repair control unit
*For illumination light
If continuity is not as specified, replace the switch.
Troubleshooting
BE±3
BE±3
BE±48
BE±50
BE±49
BE±48 Bolwer does not
work when fan
switch is on
Incorrect temperature
outputBE±3
BE±3
BE±48
Switch position Possible cause
BE±47
BE±48
Terminal Problem
Remedy
Lever
BE±52
Page
BE±54 Push
OFF
± BODY ELECTRICAL SYSTEMHeaterBE±47

Heater Relay
INSPECTION OF RELAY
1. INSPECT RELAY CONTINUITY
(a) Check that there is continuity between terminals 1
and 3.
(b) Check that there is continuity between terminals 2
and 4.
(e) Check that there is no continuity between terminals
4 and 5.
If continuity is not as specified, replace the relay.
2. INSPECT RELAY OPERATION
(a) Apply battery voltage to terminals 1 and 3.
(b) Check that there is continuity between terminals 4
and 5.
(e) Check that there is no continuity between terminals
2 and 4.
If operation is not as specified, replace the relay.
Heater Blower Resistor
INSPECTION OF RESISTOR
INSPECT RESISTOR CONTINUITY
(Levertype)
Check that there is continuity between terminals 1 and 3.
If there is no continuity, replace the resistor.
(Push type)
Check that there is continuity between terminals 5 and ^.
If there is no continuity, replace the resistor.
± BODY ELECTRICAL SYSTEMHeaterBE±48

Blower Speed Control Relay
(Push Type)
INSPECTION OF RELAY
1. INSPECT RELAY ºAº CONTINUITY
(a) Check that there is continuity between terminals 5
and 7.
(b) Check that there is no continuity between terminals
3 and 4.
If continuity is not as specified, replace the relay. 5. INSEPCT RECIRC/FRESH CONTROL SWITCH
CONTINUITY
Inspect the switch continuity between terminals. 4. INSPECT AIR VENT MODE SWITCH CONTINUITY
Inspect the switch continuity between terminals.
If continuity is not as specified, replace the heater control.
If continuity is not as specified, replace the heater control.
Switch
positionSwitch
position
FOOT/DEFBI±LEVELTerminal
Terminal
RECiRC
FRESH
FA C E
FOOT
Al 7 A10 At 7
A11
DEF
A12
A15
± BODY ELECTRICAL SYSTEMHeaterBE±50