1986 TOYOTA CAMRY V20 panel

(d) Close the sliding roof panel by hand so the clearance
between the left and right sides of the sliding roof panel
and roof panel are equal.
(e) Contact the front shoes with the stopper, install it.
(f) Apply liquid sealer to 2 or 3 threads of the bolt end.
Sealant: Part No. 08833±Q0070, THREE BOND 1324, or
equivalent
(g) Install the drive motor with the three bolts.
(h) Connect the drive motor connector. 2. INSTALL GUIDE RAIL COVER
(a) Apply liquid sealer to 2 or 3 threads of the bolt end.
Sealant: Part No. 08833±00070, THREE BOND 1324, or
equivalent
(b) Install the rail cover with the screw.
HINT: Do not damage the roof headlining.
3. INSTALL WIND DEFLECTOR
INSTALLATION OF SUN ROOF
(See page BO±53)
1. INSTALL SLIDING ROOF GLASS WITH GUIDE RAIL
ONTO ROOF
(a) Place the sliding roof glass with the guide rail onto the
roof.
(b) Tighten the guide rail with the four screws.
5. INSTALL FRONT SIDE ROOF HEADLINING
(a) Stick the double±stick tape between front and rear
pillar as shown.
(b) Install the roof headlining to the roof panel. 4. INSTALL SLIDING ROOF DRIVE MOTOR
(a) Remove the screw and cam plate cover.
(b) Align the housing and gear point mark.
(c) Install the cam plate cover and screw.
± BODYSun RoofBO±60

(b) (CANADA)
Install the shoulder belt anchor with the bolt.
Torque: 440 kg±cm (32 ft±Ib, 43 N±m)
7. INSTALL CENTER PILLAR LOWER GARNISH
8. INSTALL SCUFF PLATE
9. INSTALL FOLLOWING PARTS:
wFront pillar garnish
wRear view mirror
wSun visor and holder
wAssist grip
wOpening trim moulding
10. INSTALL CONTROL SWITCH
11. INSPECT AND ADJUST SLIDING ROOF
(See pages BO±54 and 55)
12. CONNECT BATTERY CABLE TO NEGATIVE
TERMINAL
REMOVAL OF SLIDING ROOF GLASS
(See page BO±53)
TO REMOVE ONLY SLIDING ROOF GLASS
(a) Slide the sunshade trim rearward.
(b) Remove the inner panel side garnish.
(e) Remove the front and rear shoe nuts.
(d) Remove the roof glass. 6. INSTALL CENTER PILLAR UPPER GARNISH
(a) Install the center pillar upper garnish¿¿ tapping.
± BODYSun RoofBO±61

REMOVAL OF SAFETY PAD
(See pages BO±62, 63)
1. DISCONNECT BATTERY CABLE FROM NEGATIVE
TERMINAL
2. REMOVE STEERING WHEEL
3. REMOVE FRONT PILLAR GARNISH
Pry out the clips and pull the front pillar garnish upward
to remove it by the hand.
4. REMOVE NO. 1 UNDER COVER
5. REMOVE LOWER FINISH PANEL
(a) Remove the two screws and the engine. hood re-
lease lever. HINT: Screw sizes in the previous illustration are indi-
cated by following the code below for removal and
installation of safety pad.
mm (in.)
Shape
ShapeShapeCode
CodeCodeSizeSizeSize
± BODYSafety PadBO±64

(b) (USA)
Using a screwdrier, pry out the switch bases and the
No. 1 speaker panel.
HINT: Tape the screwdrier tip before use.
7. REMOVE CLUSTER FINISH PANEL
(a) Remove the five screws and the panel.
(b) Disconnect the connectors.(d) (CANADA)
Remove the five screws and lower finish panel.
(e) Disconnect the connectors.(c) (USA)
Remove the seven bolts and lower finish panel.
6. REMOVE STEERING COLUMN COVER
Remove the four screws, the two bolts, and the cover.
± BODYSafety PadBO±65

8. REMOVE COMBINATION METER
(a) Remove the four screws.
(b) Remove the speedometer cable, connectors and the
meter.
9. REMOVE NO.2 UNDER COVER
10. (USA)
REMOVE GLOVE COMPARTMENT BOX
(a) Remove the screw and pull out the chech arm.
(b) Remove the four screws, the connector, and pull out
the box.
12. REMOVE RIGHT LOWER PANEL
(a) (USA)
Using a screwdrier, pry out the No. 2 speaker panel.
HINT: Tape the screwdriver tip before use. 11. REMOVE GLOVE COMPARTMENT DOOR
Remove the two screws and the door.
± BODYSafety PadBO±66

13. REMOVE CENTER CLUSTER FINISH PANEL
(a) (USA)
Remove the two screws.
(b) Remove the ash tray.
(c) Using a screwdriver, release the white plastic clip at
the rear of the ash receptacle retainer.
HINT: Tape the screwdrier tip before use.
(d) Pull out the center cluster finish panel.(e) (CANADA)
Remove the five screws.
(d) Remove the panel and disconnect the speaker con-
nector.
14. REMOVE RADIO AND STEREO
(a) Remove the four screws, radio and stereo.
(b) Disconnect the connectors and the antenna cable.(b) (USA)
Remove the five bolts, the three screws and the twc
nuts.
± BODYSafety PadBO±67

16. REMOVE CENTER LOWER PANEL
(a) (USA)
Remove the two screws and pull out the panel. 15. REMOVE NEATER CONTROL
Remove the four screws and the heater control.
18. REMOVE NUT CONNECTING CENTER BRACKET
AND SAFETY PAD 17. REMOVE SIDE DEFROSTER NOZZLE
HINT: Tape the screwdriver tip before use. (b) (CANADA)
Remove the three screws and panel.
± BODYSafety PadBO±68

21. REMOVE NO.1 HEATER REGISTER DUCT
Pry out the clip and remove the duct.
22. REMOVE NO.3 HEATER REGISTER DUCT
Remove the three screws and duct.
23. REMOVE DEFROSTER NOZZLE
Remove the five screws and nozzle.
24. REMOVE NO.1 INSTRUMENT PANEL REGISTER
Remove the two screws and register.
25. REMOVE NO.3 INSTRUMENT PANEL REGISTER
Remove the three screws and register.
26. REMOVE NO.2 INSTRUMENT PANEL REGISTER
Remove the screws and register.
27. REMOVE SAFETY PAD GARNISH
INSTALLATION OF SAFETY PAD
(See pages BO±62, 63)
INSTALL SAFETY PAD PARTS FOLLOWING REMOVAL
SEQUENCE IN REVERSE
HINT:
wWhen reinstall the speedometer cable, first pull on
the cable guide casing.
wInsert the flange of def±nozzle between the rib (A)
and the safety pad.
± BODYSafety PadBO±70