2019 MITSUBISHI L200 Owner's Manual (in English)

3-To adjust seat cushion height (driver’s
side only of Club cab and Double cab)
Turn the dial and adjust the seat cushion height to the desired position.
Power type*
1- To adjust forward or backward Operate the switch as indicated by thearrows and adjust the seat to the desired
position.
2- To recline the seatback Operate the switch as indicated by the
arrows and adjust the seatback angle to
the desired position.
3- To adjust seat height Operate the switch as indicated by thearrows and adjust the seat height to the
desired position.
If the entire switch is operated, then the entire seat moves.
4- To adjust seat cushion angle
Operate the switch as indicated by thearrows and adjust the seat cushion angle
to the desired position.NOTEz To prevent the battery from running down,
operate the switch with the engine running.Heated seats*
The heated seats can be operated with the ig-
nition switch or the operation mode in ON. Operate the switch as indicated by arrows.
The indication lamp (A) will illuminate while the heater is on.
1 (HI)Heater high (for quick heating).2Heater off.3 (LO)Heater low (to keep the seat
warm).CAUT,ONz Operate in the high position for quick heat-
ing. Once the seat is warm, set the heater to low to keep it warm. Slight variations in seat
temperature may be felt while using the heated seats. This is caused by the operation
of the heater’s internal thermostat and does not indicate a malfunction.
z If the following types of persons use the
heated seats, they might become too hot or
receive minor burns (red skin, heat blisters, etc.):

CAUT,ONzIf water or any other liquid is spilled on the
seat, allow it to dry thoroughly before at-tempting to use the heater.
z Turn the heater off immediately if it appears
to be malfunctioning during use.Rear seat (Club cab and
Double cab)*
When a person is sitting in the middle seating position of the rear seat, adjust the head re-straint to height at which it lock in position.
Refer to “Head restraints*” on page 4-05.
(Double cab)
Folding the seatback forward
(Double cab)
Pull up the band on the top of the seatback
and fold it forward.
To return
Raise the seatback until it is locked securely
in place.
Push and pull the seatback lightly to be sure
it is secure.
Folding up the seat cushion
(Club cab)*
The right and left seat cushions can be folded up separately.
To fold the seat cushions up, raise the seat
cushions.
Securely retain the seat cushion by hooking the retaining band (A) onto the head restraint
(B) of the rear seat.
Armrest (Double cab)
To use the armrest, fold it down.
To return to the original position, push it
backward (into the seatback) until it is level
with the seat. (Double cab)NOTEz Do not climb or sit on the armrest. Doing so
could damage the armrest.
z The top surface of the armrest contains a cup
holder for rear seat occupants.
Refer to “Cup holder” on page 7-104.
Rear seat (Club cab and Double cab)*
4-042.7((Seat and seat belts4

Head restraints*:ARN,NGzDriving without the head restraints in
place can cause you and your passengers serious injury or death in an accident. To
reduce the risk of injury in an accident,
always make sure the head restraints are installed and properly positioned when
the seat is occupied.
z Never place a cushion or similar device on
the seatback. This can adversely affect head restraint performance by increasing
the distance between your head and the restraint.
To adjust height
Front seats
Adjust the head restraint height so that the
centre of the head restraint is as close as pos-
sible to ear level to reduce the chances of in- jury in the event of collision. Any person too
tall for the head restraint to reach their seated ear level, should adjust the restraint as highas possible.
To raise the head restraint, move it upward.
To lower the restraint, move it downward while pushing the height adjusting knob (A)
in the direction of the arrow. After adjust- ment, push the head restraint downward andmake sure that it is locked.
Rear centre seat
To reduce the risk of injury in an accident,pull up the head restraint to the locked posi- tion.

To raise the head restraint, move it upward.
To lower the restraint, move it downward while pushing the height adjusting knob (A)in the direction of the arrow. After adjust-
ment, push the head restraint downward and make sure that it is locked.
Head restraints*
4-052.7((Seat and seat belts4

:ARN,NGzWhen a person sits in the middle seating
position of the rear seat, pull up the head
restraint to a height at which it locks in position. Be sure to make this adjustment
before starting to drive. Serious injuries
could otherwise be suffered as the result of an impact. (Double cab)NOTEz The head restraint height of the outer seat in
the rear seat cannot be adjusted.
To remove
Lift the head restraint with the height adjust-
ing knob (A) pushed in.
To install
Confirm that the head restraint is facing the
correct direction, and then insert it into the
seatback while pressing the height adjusting knob (A) in the direction indicated by the ar-
row.
The head restraint stalk with the adjustment notches (B) must be installed in the hole withthe adjusting knob (A) (except head restraints
of the outer seat).
CAUT,ONz Confirm that the height adjusting knob (A)
is correctly adjusted as shown in the illustra- tion, and also lift the head restraints to en- sure that they do not come out of the seat-back.CAUT,ONz The shape and size of the head restraint dif-
fers according to the seat. Always use the
correct head restraint provided for the seat and do not install the head restraint in the
wrong direction.
Head restraints*
4-062.7((Seat and seat belts4

Seat belts
To protect you and your passengers in the event of an accident, it is most important that
the seat belts are worn correctly while driv- ing.
The front seat belts each have a pretensioner system. (Single cab and Club cab)
The front seat belts and the rear outer seat belts each have a pretensioner system. (Dou-
ble cab)
These belts are used the same way as a con- ventional seat belt.
Refer to “Seat belt pretensioner system and force limiter system*” on page 4-10.:ARN,NGz Seat belts should always be worn by every
adult who drives or rides in this vehicle, and by all children who are tall enough to
wear seat belts properly.
Other children should always use proper child restraint systems.
z Always place the shoulder belt over your
shoulder and across your chest. Never put
it behind you or under your arm.
z One seat belt should be used by only one
person. Doing otherwise can be danger-
ous.:ARN,NGz The seat belt will provide its wearer with
maximum protection if the recliner seat- back is placed in fully upright position.
When the seatback is reclined, there is
greater risk that the passenger will slide
under the belt, especially in a forward im- pact accident, and may be injured by the
belt or by striking the instrument panel or seatbacks.
z Remove any twists when using the belt.
z No modifications or additions should be
made by the user which will either pre-
vent the seat belt adjusting devices from operating to remove slack, or prevent theseat belt assembly from being adjusted to remove slack.
z Never hold a child in your arms or on
your lap when riding in this vehicle, even
if you are wearing your seat belt. To do so risks severe or fatal injury to the child in
a collision or sudden stop.
z Always adjust the seat belt to a snug fit.
z Always wear the lap portion of the belt
over your hips.3-point type seat belt (with
emergency locking mechanism)
This type of belt requires no length adjust-
ment. Once worn, the belt adjusts itself to the movement of the wearer, but in the event of a
sudden or strong shock, the belt automatical-
ly locks to hold the wearer’s body.
NOTEz You can check if the belt locks by pulling it
forward quickly.
To fasten
1. Pull the seat belt out slowly while hold-
ing the latch plate.
NOTEz When the seat belts cannot be pulled out in a
locked condition, pull the belts once force-
fully and then return them. After that, pull
the belts out slowly once again.
2. Insert the latch plate into the buckle until
a “click” is heard.
Seat belts
4-072.7((Seat and seat belts4

:ARN,NGzNever wear the lap portion of the belt
across your abdomen. During accidents it
can press sharply against the abdomen and increase the risk of injury.
z The seat belts must not be twisted when
worn.
3. Pull the belt slightly to adjust slackness
as desired.
To unfasten
Hold the latch plate and push the button on
the buckle.
NOTEz As the belt retracts automatically, keep hold-
ing the latch plate while retracting so that the
belt stows slowly. Failure to do this could damage the vehicle.NOTEz If the seat belt (A) or ring (B) becomes dirty,
the belt may not retract smoothly. If the seat
belt and ring are dirty, clean them with a
mild soap or detergent solution.Seat belt reminder

For the driver and the frontpassenger

NOTEzWhen luggage is placed on the front passen-
ger seat, a sensor in the seat cushion may,
depending on the weight and position of the
luggage, cause the warning tone to sound and the warning lamp to come on. (Club cab
and Double cab)For the rear passenger

Pregnant women restraint:ARN,NGzSeat belts work for everyone, including
pregnant women. Pregnant women should
use the available seat belts. This will re- duce the likelihood of injury to both thewoman and the unborn child. The lap belt
should be worn across the thighs and as snug against the hips as possible, but not
across the waist. Consult your doctor if you have any additional questions or con-
cerns.Seat belt pretensioner
system and force limiter system*
The front seat belts each have a pretensioner system and force limiter system. (Single caband Club cab)
The front seat belts and the rear outer seat
belts each have a pretensioner system and
force limiter system. (Double cab)
Pretensioner system
When the ignition switch or the operation
mode is under the following conditions, if
there is a frontal impact or a side impact (ve-
hicles equipped with SRS side airbags and SRS curtain airbags) severe enough to injure the driver and/or front passenger or when arollover or overturning of the vehicle is de-
tected (if so equipped), the pretensioner sys-
tem will retract the respective seat belts in- stantaneously, thus maximizing the seat belt’s
effectiveness.
[Except for vehicles equipped with keyless operation system@
The ignition switch is in the “ON” or
“START” position.
[Vehicles equipped with keyless operation system@
The operation mode is in ON.
:ARN,NGz To obtain the best results from your pre-
tensioner seat belt, make sure you have adjusted your seat correctly and wear your seat belt properly.CAUT,ONz Installation of audio equipment or repairs in
the vicinity of the pretensioner seat belts or
floor console must be performed in line with MITSUBISHI MOTORS guidelines. It is
important to do so because the work could affect the pretensioner systems.
z If you need to scrap the vehicle, please con-
sult a MITSUBISHI MOTORS Authorized
Service Point. It is important to do so be- cause unexpected activation of the preten-
sioner seat belts could cause injuries.NOTEz The pretensioner seat belts will be activated
if the vehicle suffers a severe impact, even if
the seat belts are not worn.
z The pretensioner seat belts are designed to
work only once. After the pretensioner seat
belts have been activated, we recommend
you to have them replaced by a MITSUBISHI MOTORS Authorized Serv-
ice Point.SRS warning lamp
This warning lamp is shared by the SRS air-
bags and the pretensioner seat belts.
Refer to “SRS warning lamp” on page 4-34.
Pregnant women restraint
4-102.7((Seat and seat belts4