2019 MITSUBISHI L200 Owner's Manual (in English)

Position lamps
1.When replacing the bulb on the left side
of the vehicle, remove the clip (A) hold-
ing down the washer tank spout and move the spout towards the rear of the
vehicle.
2. Turn the bulb socket anticlockwise to re-
move it. And remove the bulb from the socket by pulling out.
3. To install the bulb, perform the removal
steps in reverse.
Front turn-signal lamps
Except for vehicles with high in- tensity discharge headlamps
1. When replacing the bulb on the left side
of the vehicle, remove the clip (A) hold- ing down the washer tank spout and
move the spout towards the rear of the
vehicle.
2. Turn the bulb socket anticlockwise to re-
move it. And remove the bulb from the socket by turning it anticlockwise while
pressing in.
3. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
10-252.7((Maintenance10

Vehicles with high intensity dis-charge headlamps
1. When replacing the bulb on the left side
of the vehicle, remove the clip (A) hold-
ing down the washer tank spout and move the spout towards the rear of the
vehicle.
2. Turn the bulb socket anticlockwise to re-
move it. And remove the bulb from the socket by turning it anticlockwise while
pressing in.
3. To install the bulb, perform the removal
steps in reverse.
Front fog lamps* / Daytime
running lamps*
1. Insert a straight blade (or minus) screw-
driver with a cloth over its tip at the edge
of the cover (A) and pry gently to re-
move the cover.
2. Remove the 3 screws (B) and remove
the lamp unit.
Replacement of lamp bulbs
10-262.7((Maintenance10

NOTEzWhen unfastening the screws of the fog
lamp, be careful not to mistakenly move thebeam position adjustment screw (C).
3. Turn the socket anticlockwise to remove
it.
D- Front fog lamp
E- Daytime running lamp
4. While holding down the tab (F), pull out
the bulb (G).
5. To install the bulb, perform the removal
steps in reverse.
Rear combination lamps
1. Open the rear gate. (Refer to “Rear gate” on page 3-20.)
2.Remove the screws (A) that hold the
lamp unit.
3. Move the lamp unit towards the rear of
the vehicle and remove the clips (B).
Replacement of lamp bulbs
10-272.7((Maintenance10 Type 1 Type 2 Type 3 Front fog lamp Daytime running lamp

4.Remove each socket and bulb assembly
by turning it anticlockwise.C-Tail and stop lamp
Remove the bulb from the sock- et by turning it anticlockwise
while pressing in.D-Rear turn-signal lamp
Remove the bulb by pulling it
out.E-Rear fog lamp (driver’s side)*/ Reversing lamp
Remove the bulb by pulling it
out.
5. To install the bulb, perform the removal
steps in reverse.
NOTEz When mounting the lamp unit, align the pins
(F) and clip (G) on the lamp unit with the
holes (H) in the body.Licence plate lamps
1. Insert a straight blade (or minus) screw-
driver into the lamp assembly and pry
gently to remove it.
NOTEz Wrap a piece of cloth around the tip of the
screwdriver in order to avoid scratching the
lens and the body.
2. Remove the socket and bulb assembly
together by turning it anticlockwise, and then remove the bulb by pulling it out.
3. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
10-282.7((Maintenance10

NOTEzWhen mounting the lamp unit, put the hook
(A) on the right side of the lamp unit into thebody first.Front room map lamps*
1. Insert a straight blade (or minus) screw-
driver into the notch of the lens and pry gently to remove it.
Remove the bulb from the lamp holder.
NOTEz Wrap a piece of cloth around the tip of the
screwdriver in order to avoid scratching the
lens.
2. To install the bulb, perform the removal
steps in reverse.
NOTEz When installing the lens, align the 2 tabs on
the lens with the holes on the vehicle side.Rear room lamp
Type 1
1. Insert a straight blade (or minus) screw-
driver into the notch of the lens and pry
gently to remove it. Remove the bulb
from the lamp holder.NOTEz Wrap a piece of cloth around the tip of the
screwdriver in order to avoid scratching the
lens.
2. To install the bulb, perform the removal
steps in reverse.
NOTEz When installing the lens, align the 2 tabs on
the lens with the holes on the vehicle side.
Replacement of lamp bulbs
10-292.7((Maintenance10

NOTEzWhen installing the lens, fit the two tabs on
one side of the lens into the holes on the ve-hicle side before fitting the two tabs on the opposite side of the lens into the holes on the
vehicle side.
Type 2
1. Insert a straight blade (or minus) screw-
driver into the notch of the lens and pry
gently to remove it. Remove the bulb
from the lamp holder.NOTEz Wrap a piece of cloth around the tip of the
screwdriver in order to avoid scratching the
lens.
2. To install the bulb, perform the removal
steps in reverse.
NOTEz When installing the lens, fit the two tabs on
one side of the lens into the holes on the ve-hicle side before fitting the two tabs on the opposite side of the lens into the holes on the
vehicle side.Glove box lamp
Have the glove box lamp bulb replaced at a
MITSUBISHI MOTORS Authorized Service
Point.
Masking the headlamps
When entering a country in which vehicles are driven on the opposite side of the road to
the country in which your vehicles is sup- plied, necessary measures have to be taken toavoid dazzling oncoming traffic.
Masking the headlamps
10-302.7((Maintenance10

High intensity discharge head-lamp type
Do not need any adjustment.
Halogen headlamp type
Mask the headlamps according to the next
procedure. 1. Turn the headlamp off and wait until the
headlamps got cold.
2. According to the illustrations, prepare
the sticker (A) to stick the headlamp sur- face of right and left.
NOTEz Use a sticker with a light blocking effect
enough.
Using of a sticker without a light blocking
effect will not acquire a blocking effect.
3. Seeing from the headlamp front, position
(C) of the sticker and the central mark
(B) of the headlamp and stick a sticker along the vertical dotted line.
NOTEz Align the vertical dotted line with the line of
the reflector in the headlamp.
Masking the headlamps
10-312.7((Maintenance10 LHDLeft lens
Right lens
115mm105mm
37mm
50mm RHDLeft lens
Right lens
105mm
37mm
50mm
115mm

2.7((