2019 MITSUBISHI L200 Owner's Manual (in English)

To temporarily decrease thespeed
Depress the brake pedal to decrease the
speed. To return to the previously set speed, push up the RES + switch (C).
Refer to “To resume the set speed” on page
6-68.
To deactivate
The set speed driving can be deactivated as follows:
z Press the CRUISE CONTROL ON/OFF
switch (A) (Cruise control will be turned off.)
z Press the CANCEL switch (D).
z Depress the brake pedal.
The set speed driving is deactivated automat-
ically in any of the following ways.
z When you depress the clutch pedal (on
vehicles with M/T).
z When your speed slows to approximate-
ly 15 km/h (9 mph) or more below the set speed because of a hill, etc.
z When your speed slows to approximate-
ly 40 km/h (25 mph) or less.
z When the Active Stability & Traction
control (ASTC) starts operating.
Refer to “Active Stability & Traction
Control (ASTC)” on page 6-59.:ARN,NGz On vehicles equipped with
A/T, although
the set driving speed will be deactivated
when shifting to the “N” (NEUTRAL) po- sition, never move the selector lever to the
“N” (NEUTRAL) position while driving.
You would have no engine braking and
could cause a serious accident.
Also, the set speed driving may be deactiva-
ted as follows:
z When the engine speed rises and ap-
proaches the tachometer’s red zone (the red-coloured part of the tachometer di-
al).
Cruise control*
6-672.7((Starting and driving6Type 1 Type 2 Type 1 Type 2

CAUT,ONzWhen the set speed driving is deactivated
automatically in any situation other thanthose listed above, there may be a system
malfunction.
Press the CRUISE CONTROL ON/OFF switch to turn off the cruise control and have your vehicle inspected by a MITSUBISHI
MOTORS Authorized Service Point.To resume the set speed
If the set driving speed is deactivated by the
condition described in “To deactivate” on page 6-67, you can resume the previously set
speed by pushing up the RES + switch (C) while driving at a speed of approximately40 km/h (25 mph) or higher.
Under either of the following conditions, however, using the switch does not allow you
to resume the previously set speed. In these
situations, repeat the speed setting procedure:
z The CRUISE CONTROL ON/OFF
switch is pressed.
z The ignition switch is turned OFF or the
operation mode is put in OFF.
z Indication lamp go off.Speed Limiter
The Speed Limiter is a driver assist function
to prevent from exceeding the speed set by
driver while engine power control.
CAUT,ONz Because the system does not use service
brake (hydraulic brake), the vehicle speedmay exceed the set speed on the downhill.
If a driver wants to keep the vehicle speed in
such a situation, he/she must put on a service brake or downshift.NOTEz If the clutch pedal
(M/T) is depressed, the
Speed Limiter does not activate.
Speed Limiter
6-682.7((Starting and driving6 Type 1 Type 2

If the vehicle speed exceeds the set speed,control state “LIMIT” and the Speed Limit-
er’s symbol will blink in the combination me- ter.
If the vehicle speed exceeds the set speed af- ter indicated control state “LIMIT” and the
Speed Limiter’s symbol, beep alert will sound a certain period of time.
While running without blinked control state “LIMIT” and the Speed Limiter’s symbol, if
you decrease the set speed and vehicle speed is more than set speed, control state “LIMIT” and the Speed Limiter’s symbol blinking
starts but beep alert is delayed.
In this case, when vehicle speed keeps ex- ceeding set speed for about 30 seconds after
control state “LIMIT” and the Speed Limit- er’s symbol are blinked, beep alert will sound
a certain period of time.
If the vehicle speeds decreases less than set
speeds, control state “LIMIT” and the Speed
Limiter’s symbol stop blinking. When beep alert is sounding, the beep alert also goes off.NOTEz However, this gives priority to audio and
visual signal of safety reasons or driver’s de-mand.
z If the set speed is too lower based on current
shift position, the Speed Limiter may not
limit the vehicle speed to prevent engine stall.Speed Limiter control switches
There are 4 switches which relate to the
Speed Limiter on the steering wheel.
A-SPEED LIMITER ON/OFF switch
To turn on/off the Speed Limiter.
B-SET - switch
To set the current vehicle speed to a set speed decrease the set speed.
C-RES + switch
To resume the Speed Limiter with set speed
memorized or increase the set speed.
D-CANCEL switch
To cancel the Speed Limiter.NOTEz Press the switch one by one.
z The Speed Limiter may be cancelled auto-
matically, if two or more switches are press-
ed at the same time.Speed Limiter information on
the multi information display area
The Speed Limiter information is displayed
on the multi information display area in the
combination meter.
A-Control state
Speed Limiter
6-692.7((Starting and driving6 Type 1 Type 2

There are 2 control states as below.LIMIT OFF
When the Speed Limiter is in STAND-
BY, the vehicle speed can exceed the set speed
LIMIT
When the Speed Limiter is in operation.
The vehicle is controlled in order not to exceed the set speed.
B-SPEED LIMITER ON indication
When the Speed Limiter is started up, the Speed Limiter’s symbol is appeared.
C-Set speed
Set speed is appeared if it is stored.To start up
First of all, press the ON/OFF switch in order to power up the Speed Limiter when the igni-
tion switch in the “ON”, position or the oper- ation mode in ON,
The Speed Limiter indication will be ap-
peared in the combination meter.To activate
Accelerate or decelerate to your desired
speed, and push down the SET - switch (B). the Speed Limiter memorizes the current ve-
hicle speed when you release the SET -
switch (B). Now, the Speed Limiter starts controlling in order not to exceed the set speed.Speed Limiter
6-702.7((Starting and driving6 Type 1 Type 2

If the current vehicle speed is lower than ap-proximately 30 km/h (19 mph) (settable min- imum speed), the set speed is set at approxi-
mately 30 km/h (19 mph).
The set speed is displayed in the combination meter.
And, control state “LIMIT” is displayed in
the combination meter.To increase the set speedBy using the RES + switch
Push up the RES + switch (C) continuously.

Then the set speed displayed in the combina-
tion meter is gradually increased.
If the set speed reaches your desired speed,
release the RES + switch (C).
The set speed is increased each approximate- ly 5 km/h (3 mph).
If a driver wants to increase the set speed a
little, push up the RES + switch (C) and re- lease it.
The set speed is increased 1 km/h each taps.
By using the CANCEL switch,
the accelerator pedal and the
SET - switch
Press the CANCEL switch (D) to deactivate the Speed Limiter.
Control state “LIMIT” is disappeared and
change control state “LIMIT OFF” in the combination meter.
Speed Limiter
6-712.7((Starting and driving6 Type 1 Type 2 Type 1 Type 2

Accelerate to driver’s desired vehicle speedand push down SET - switch (B) and release.Control state “LIMIT” is displayed again andthe set speed is updated.
To decrease the set speed

By using the SET - switch
Push down the SET - switch (B).

Then the set speed displayed in the combina- tion meter is gradually decreased.
If the set speed reaches to your desired speed,
release the SET - switch (B).
The set speed decreases each approximately5 km/h (3 mph).
If a driver wants to decrease the set speed a
little, press SET - switch (B) and release it.
The set speed is decreased 1 km/h each taps.
Speed Limiter
6-722.7((Starting and driving6 Type 1 Type 2 Type 1 Type 2

By using the CANCEL switch,the service brake and the SET - switch
Press the CANCEL switch (D) to deactivate the Speed Limiter.
Control state “LIMIT” is disappeared and
change control state “LIMIT OFF” in the
combination meter.
Decelerate to driver’s desired speed and push
down SET - switch (B) and release.The Speed Limiter indication is displayed
again and the set speed is updated.
To increase the vehicle speed
temporarily
A driver can temporarily accelerate for emer-
gency use.

The Speed Limiter is temporarily deactiva- ted, and the vehicle speed can be increased.
Speed Limiter
6-732.7((Starting and driving6Type 1 Type 2 Type 1 Type 2

The Speed Limiter will resume when the ve-hicle speed goes down to enough less than
the set speed.
Put on an accelerator pedal to the pedal
stroke end. (over a detent that makes pedal reaction force bigger before pedal stroke end)
CAUT,ONz There is a possibility for the Speed Limiter
to allow abrupt acceleration corresponding
to accelerator pedal position. So be careful
of the abrupt acceleration.If the vehicle speed exceeds the set speed, the
control state “LIMIT” and the Speed Limit-
er’s symbol will blink.CAUT,ONz Be careful about over speed.NOTEzA driver can change the set speed during this
emergency use.To deactivate
Use whichever following ways to deactivate.
z Press the CANCEL switch
z Press the Speed Limiter ON/OFF switch
NOTEzIf the Speed Limiter is cancelled by other
states, it may be a system malfunction.
Stop using the Speed Limiter and turn off
the Speed Limiter. Have your vehicle in-
spected by a MITSUBISHI MOTORS Serv-
ice Point.CAUT,ONz There is a possibility for the Speed Limiter
to allow abrupt acceleration corresponding
to accelerator pedal position when the Speed Limiter is deactivated. Be careful.To resume
The Speed Limiter memorizes the set speed
when system has been deactivated, the Speed
Limiter can resume by push up the RES + switch (C).
Speed Limiter
6-742.7((Starting and driving6 Type 1