2019 MITSUBISHI L200 Owner's Manual (in English)

If the warning lamp illuminates while the en-
gine is running, turn the engine off and have it inspected.CAUT,ONz If this lamp illuminates when the engine oil
level is not low, have it inspected.
z This warning lamp does not indicate the
amount of oil in the crankcase. This must be determined by checking the oil level on the
dipstick, while the engine is switched off.
z If you continue driving with low engine oil
level or with this warning lamp illuminated,
engine seizure may occur.NOTEz The oil pressure warning lamp should not be
treated as an indication of the engine’s oillevel. The oil level must be checked using
the dipstick.Door ajar warning lamp
This lamp illuminates when
a door is either open or not
completely closed.
If the vehicle speed reaches approximately 8 km/h
(5 mph) with a door open or
incompletely closed, a buzzer sounds 4 times as a warning.
CAUT,ONz Before moving your vehicle, check that the
warning lamp is OFF.Washer fluid level warning
lamp*
This lamp comes on when the washer fluid is running
low.
If the lamp comes on, re- plenish the container with
washer fluid.
Refer to “Washer fluid” on page 10-07.
refer to “Capacity” on page 11-17.
Combination headlamps
and dipper switch
Headlamps
NOTEz Do not leave the lamps on for a long time
while the engine is stationary (not running).A run-down battery could result.NOTEz When it rains, or when the vehicle has been
washed, the inside of the lens sometimes be-
comes foggy, but this does not indicate a functional problem.
When the lamp is switched on, the heat will
remove the fog. However, if water gathers inside the lamp, we recommend you to have
it checked.
z The bulbs of the high intensity discharge
headlamps (if so equipped) have the follow-
ing characteristics.

Type 1
Rotate the switch to turn on the lamps.
OFFAll lamps offPosition, tail, licence plate and instru-
ment panel lamps onHeadlamps and other lamps go onType 2
Rotate the switch to turn on the lamps.
OFFAll lamps off
AUTO
With the ignition switch or the
operation mode is in ON, head-
lamps, position, tail, licence plate
and instrument panel lamps turn
on and off automatically in ac-
cordance with outside light level.
All lamps turn off automatically
when the ignition switch is turned
to “OFF” position or the opera-
tion mode is put in OFF.Position, tail, licence plate and in-
strument panel lamps onHeadlamps and other lamps go onNOTEz The sensitivity of the automatic on/off con-
trol can be adjusted. For further information,contact a MITSUBISHI MOTORS Author-
ized Service Point.
z If the front fog lamps (if so equipped) turn
on when they are supposed to with the
switch in the “AUTO” position, the lamps turn off automatically with the ignition
switch or operation mode off.
z When the headlamps are turned off by the
automatic on/off control with the ignition
switch in the “ON” position or the operation
mode in ON, the front fog lamps (if so
equipped) and rear fog lamps also go off.
When the headlamps are subsequently turned back on by the automatic on/off con-
trol, the front fog lamps also come on but the
rear fog lamp stays off. If you wish to turn
the rear fog lamp back on, operate the switch again.
z Do not cover the sensor (A) for the automat-
ic on/off control by affixing a sticker or label to the windscreen.
Combination headlamps and dipper switch
5-162.7((Instruments and controls5

NOTEzIf the lamps do not turn on or off with the
switch in the “AUTO” position, manually
operate the switch and we recommend you
to have your vehicle checked.
Lamps (headlamps, fog lamp,
etc.) auto-cutout function
z If the following operation is performed
while the lamp switch is in the “” po-
sition, the lamps are automatically
turned off when the driver’s door is
opened.
[Except vehicles equipped with keyless
operation system@
The ignition switch is turned to the
“LOCK” or “ACC” position, or the key is removed from the ignition switch.
[For vehicles equipped with keyless op- eration system@
The operation mode is in OFF or ACC.
z If the following operation is performed
while the lamp switch is in the “” po-
sition, the lamps are automatically
turned off if the driver’s door then re-
mains closed for approximately three minutes.
[Except vehicles equipped with keyless
operation system@
The ignition switch is turned to the
“LOCK” or “ACC” position, or the key is removed from the ignition switch.
[For vehicles equipped with keyless op- eration system@
The operation mode is in OFF or ACC.NOTEz The lamp auto-cutout function can also be
disabled.
For further information, we recommend you
to consult a MITSUBISHI MOTORS Au-
thorized Service Point.Lamp monitor buzzer
If the following operation is performed, a
buzzer will sound to remind the driver to turn
off the lamps.
[Except for vehicles equipped with keyless
operation system@
If the driver’s door is opened when the key is
in the “LOCK” or “ACC” position or re-
moved from the ignition switch while the lamps are on.
[For vehicles equipped with keyless opera-
tion system@
If the driver’s door is opened when the opera- tion mode is in ACC or OFF while the lamps
are on.

In both cases, the buzzer will automatically stop if the auto-cutoff function is activated,
the lamp switch is turned off, or the door is closed.Daytime running lamp
The daytime running lamps comes on when
the engine is running and the lamp switch is in the “OFF” or “AUTO” position and the taillamps are off.
Combination headlamps and dipper switch
5-172.7((Instruments and controls5

Dipper (High/Low beamchange)
When the lamp switch is in the “” posi-
tion, the beam changes from high to low (or
low to high) each time the lever is pulled
fully (1). While the high-beam is on, the
high-beam indication lamp in the instrument
cluster will also illuminate.
Headlamp flasher
The high-beams flash when the lever is
pulled slightly (2), and will go off when it is released.
When the high-beam is on, the high-beam in- dication lamp in the instrument cluster will il-
luminate.
NOTEz The high-beams can also flash when the
lamp switch is OFF.
z If you turn the lamps off with the headlamps
set to high-beam, the headlamps are auto- matically returned to their low-beam setting
when the lamp switch is next turned to the
“
” position.
Headlamp levelling switch
The angle of the headlamp beam varies de-
pending on the load carried by the vehicle.
The headlamp levelling switch can be used to adjust the headlamp illumination distance(when the lower beam is illuminated) so that the headlamps’ glare does not distract the
drivers of approaching vehicles.
Set the switch (referring to the following ta-
ble) to the appropriate position according to the number of people and the load in the ve-hicle.CAUT,ONz Always perform adjustments before driving.
Do not attempt to adjust while driving, as it could cause an accident.NOTEz When adjusting the beam position, first put
the dial in the “0” position (the highest beamposition).Vehicle con-
dition
(Single cab)
Headlamp levelling switch
5-182.7((Instruments and controls5

Switch posi-tion“0”“2”

Hazard warning flasherswitch
Use the hazard warning flasher switch when
the vehicle has to be parked on the road for
any emergency.
The hazard warning flashers can always be
operated, regardless of the ignition switch po-
sition or the operation mode.
Push the switch to turn on the hazard warning flashers, all turn-signal lamps flash continu-
ously.
To turn them off, push the switch again.NOTEz On vehicles equipped with the emergency
stop signal system, while the hazard warning lamps are blinking due to having manually
pushed the switch, the emergency stop signal
system does not operate.
Refer to “Emergency stop signal system*” on page 6-56.Fog lamp switch*Front fog lamp switch*
The front fog lamps can be operated while
the headlamps or tail lamps are on. Turn the
knob in the “ON” direction to turn on the front fog lamps. An indication lamp in the in-
strument cluster will also come on. Turn the knob in the “OFF” direction to turn off the front fog lamps. The knob will automatically
return to its original position when you re- lease it.
NOTEz The front fog lamps are automatically turned
off when the headlamps or tail lamps are turned off. To turn the front fog lamps on again, turn the knob in the “ON” directionafter turning on the headlamps or tail lamps.
z Do not use fog lamps except in conditions of
fog, otherwise excessive lamp glare may temporarily blind oncoming vehicle drivers.Rear fog lamp switch
The rear fog lamp can be operated when the
headlamps or front fog lamps (if so equipped)
turn on.
An indication lamp in the instrument cluster comes on when the rear fog lamp is turned
on.

[Vehicle without front fog lamps@
Turn the knob once in the “ON” direction to turn on the rear fog lamp. To turn the rear fog lamp off, turn the knob once in the “OFF” di-
rection. The knob will automatically return to
its original position when you release it.

[Vehicle with front fog lamps@
Hazard warning flasher switch
5-202.7((Instruments and controls5

Turn the knob once in the “ON” direction toturn on the front fog lamps. Turn the knob once more in the “ON” direction to turn on
the rear fog lamp. To turn the rear fog lamp off, turn the knob once in the “OFF” direc-
tion. Turn the knob once more in the “OFF” direction to turn off the front fog lamps. The
knob will automatically return to its original
position when you release it.NOTEz The rear fog lamp is automatically turned off
when the headlamps or front fog lamps (if so equipped) are turned off.
z To turn the rear fog lamp on again, turn the
knob once in the “ON” direction after turn-ing on the headlamps. (Vehicle without frontfog lamps)NOTEz To turn the rear fog lamp on again, turn the
knob twice in the “ON” direction after turn- ing on the headlamps. (Vehicle with front
fog lamps)Wiper and washer switch
The windscreen wipers and washer can be
operated with the ignition switch or the oper- ation mode in ON or ACC.
If the blades are frozen to the windscreen, do
not operate the wipers until the ice has mel- ted and the blades are freed, otherwise thewiper motor may be damaged.
CAUT,ONz If the washer is used in cold weather, the
washer fluid sprayed against the glass may freeze, which may hinder visibility. Warm
the glass with the defroster or rear window demister before using the washer.Windscreen wipersExcept for vehicles equipped
with rain sensorMIST-Misting function
The wipers will operate once.OFF-OffINT-Intermittent (Speed sensitive)LO-SlowHI-Fast
Wiper and washer switch
5-212.7((Instruments and controls5

To adjust intermittent intervals
With the lever in the “INT” (speed sensitiveintermittent operation) position, the intermit-
tent intervals can be adjusted by turning the knob (A).
1- Fast
2- Slow
NOTEz The speed-sensitive-operation function of
the windscreen wipers can be deactivated.
For further information, we recommend you to consult a MITSUBISHI MOTORS Au-
thorized Service Point.
Misting function
Move the lever in the direction of the arrow
and release, to operate the wipers once.
Use this function when you are driving in
mist or drizzle.Vehicles with rain sensorMIST-Misting function
The wipers will operate once.OFF-OffAUTO-Auto-wiper control
Rain sensor
The wipers will automatically
operate depending on the degree
of wetness on the windscreen.LO-SlowHI-Fast
Rain sensor
Can only be used when the ignition switch or the operation mode is in ON.
If the lever is put in the “AUTO” position,
the rain sensor (A) will detect the extent of rain (or snow, other moisture, dust, etc.) andthe wipers will operate automatically.
Keep the lever in the “OFF” position if the
windscreen is dirty and the weather is dry.
Wiper operation under these conditions can scratch the windscreen and damage the wip-
ers.
Wiper and washer switch
5-222.7((Instruments and controls5