2017 KIA OPTIMA PLUG-IN HYBRID Owners Manual

LKAS malfunction
0+'-
• If there is a problem with the systema message will appear. If the problem
continues the LKAS fail indicator will illuminate.
LKAS fail indicator
0+'-
The LKAS fail indicator (yellow) will illu‐
minate with an audible warning if the LKAS is not working properly. We rec‐
ommend that you contact an author‐
ized Kia dealer.
When there is a problem with the sys‐tem do one of the following:
• Turn the system on after turning the engine off and on again.
• Check if the ignition switch is in the ON position.
• Check if the system is affected by the weather. (ex: fog, heavy rain,
etc.) • Check if there is foreign matter on
the camera lens
If the problem is not solved, we recom‐
mend that the system be checked by
an authorized Kia dealer.
Driving your vehicle
7-88

LKAS function changeThe driver can change LKAS to Lane
Departure Warning System (LDWS) or change the LKAS mode between Stand‐
ard LKA and Active LKA from the User
Settings Mode on the LCD display. The system is automatically set to Stand‐
ard LKA.
Lane Departure Warning system
(LDWS)
• The system can be converted to LKA to LDW at the User setting mode.
• Refer to L

• LDW is generated when the vehicle isabout to cross the line.
Active LKA
• LKAS operates for a vehicle to keepthe region of lane center more effi‐
ciently.
• The steering assistance is activated more frequently and earlier than
standard LKA.
• LDW is generated when the vehicle is about to cross the line.
Driving your vehicle
7-90

BLIND SPOT DETECTION SYSTEM (BSD) (IF EQUIPPED)
06.-
The BSD (Blind spot detection) system
uses a radar sensor to alert the driver while driving.
It senses the rear side territory of the
vehicle and provides information to the
driver. 1. BSD (Blind spot detection)
Warning range is dependent on
your vehicle speed. However, if the
speed of your vehicle is faster by
10 km/h or more than other nearby
vehicles, the warning is not operat‐
ed.
2. LCA (Lane change assist) When vehicles are approaching toyour vehicle at high speed, the
warning is operated.
3. RCTA (Rear cross traffic alert) When your vehicle moves back‐
ward, the sensor detects approach‐
ing vehicles to the left or right side
direction and warning is operated.
WARNING
•Always check the road conditionwhile driving for unexpected situa‐tions even though the BSD (Blindspot detection) system is operat‐ing.
•BSD (Blind spot detection) systemis a system made for convenience.Do not solely rely on the systembut always pay attention to drivesafely.
BSD (Blind spot detection) / LCA
(Lane Change Assist)
Operating conditions
The indicator on the switch will illumi‐
nate when the BSD (Blind spot detec‐ tion) system switch is pressed with the
engine start/stop button switch ON. If
the vehicle speed exceeds 30 km/h (18.6 mph), the system will activate.
If you press the switch again, the
switch indicator and system will be
turned off.
If the engine start/stop button switch is turned OFF and ON the system re‐
turns to the previous state.

7-91
7
Driving your vehicle

When the system is not used turn the
system off by pressing the switch.
When the system is turned on the warning light will illuminate for 3 sec‐
onds on the outside rearview mirror.
Warning type
The system will activate when: 1. The system is on
2. Vehicle speed is above 30 km/h (18.6 mph)
3. Other vehicles are detected in the rear side
TU
TUBHF
06.
If a vehicle is detected within the boun‐
dary of the system, a warning light will illuminate on the outside rearview mir‐
ror. If the detected vehicle is not in detec‐
tion range, the warning will be turned off.
OE
TUBHF
06.
The second stage alarm will activate
when: 1. The first stage alert is on
2. The turn signal is on to change a lane
When the second stage alert is activa‐ ted, a warning light will be blinking on
the outside rearview mirror and an
alarm will sound.
If you move the turn signal switch to origin position, the second stage alert
will be deactivated. The second stage alarm can be deacti‐
vated. • To activate the alarm: Go to the User Settings Mode
Sound and select "BSD" on the LCD
display.
• To deactivate the alarm: Go to the User Settings Mode
Sound and deselect "BSD" on the LCD
display.
CAUTION
The alarm function helps alert thedriver. Deactivate this function onlywhen it is necessary
Driving your vehicle
7-92

Detecting sensor
The sensors are located inside the rear
bumper.
Always keep the rear bumper clean for the system to work properly.
Warning message
0+'-
The message will appear to notify the
driver if there are foreign substances on the rear bumper or it is hot near the
rear bumper. The light on the switch
and the system will be turned off auto‐ matically.
Remove the foreign substance on the
rear bumper.
After the foreign substance is removed,
if you drive for approximately 10 mi‐ nutes, the system will work normally.
If the system does not work normally
even though the foreign substance is
removed, take your vehicle to an au‐ thorized Kia dealer and have the sys‐
tem checked. It is possible to get the message with
no foreign substance on the rear bumper, for example, when driving in
sparse rural or open area, such as des‐
ert, where there is insufficient data for operation.
This message may also activate during
heavy rain or due to road spray.
In this case, the vehicle does not need
service.
0+'-
If the system does not work properly, a
warning message will appear and the light on the switch will turn off. The
system will turn off automatically.
We recommend you to have the sys‐
tem checked by an authorized Kia deal‐ er.

7-93
7
Driving your vehicle

RCTA (Rear Cross Traffic Alert)
0:',
When your vehicle moves backwards
from a parking position, the sensor de‐ tects approaching vehicles to the left or
right side direction and gives informa‐
tion to the driver.
Operating conditions
0+'-
• Select RCTA (Rear Cross Traffic Alert) in "User Settings" under "Driving As‐
sist" on the instrument cluster. The system will turn on and stand by to
be activated.
• Select RCTA again, to turn the sys‐ tem off.
• If the vehicle is turned off and on again, the RCTA system will return to
the state right before the vehicle was turned off. Turn the RCTA system off
when not in use.
• The system is operated when the ve‐ hicle speed is below 10 km/h with the
shift lever in R (Reverse). • The RCTA (Rear Cross Traffic Alert)
detection range is 0.5 m~20 m based
on side direction. If an approaching vehicle speed is 7 km/h~36 km/h in
detection range, The warning is on.
However, the system sensing range is
different based on conditions. Always
pay attention to surrounding.
Driving your vehicle
7-94

Warning type
0+'-
0+'-
0+'-
• If an approaching vehicle detected bysensors, the warning is chime and the
warning light will blink on the outside
rearview mirror.
• If the detected vehicle is out of de‐ tection range, moving away in the
opposite direction or moving slow,
the warning is cancelled.
• The system may not be operating properly due to other factors or cir‐
cumstances, so always pay attention to your surrounding.
❈ If the bumper on either side is
blocked by a barrier or vehicles, the
system sensing ability may be de‐
teriorated.
WARNING
•The warning light on the outsiderearview mirror will illuminatewhenever a vehicle is detected atthe rear side by the system.To avoid accidents, do not focusonly on the warning light and ne‐glect to see the surrounding of thevehicle.
•Drive safely even though the vehi‐cle is equipped with a BSD (Blindspot detection) system. Do notsolely rely on the system butcheck for yourself before changinglanes.The system may not alert thedriver in some conditions so al‐ways check the surroundings whiledriving.
CAUTION
•The system may not work proper‐ly if the bumper has been replacedor if a repair work has been donenear the sensor.
(Continued)

7-95
7
Driving your vehicle