2016 NISSAN NOTE trans

TM-98
< SYSTEM DESCRIPTION >[CVT: RE0F11A]
DIAGNOSIS SYSTEM (TCM)
WORK SUPPORT
*: “Clutch point learning” can
be selected, but do not use it.
Engine brake adjustment
Check the degradation level of the CVT fluid.
G SEN SLOPE (%) Displays the gradient angle calculated from the G sensor
signal voltage.
ENGBRKLVL (On/Off) Displays the setting of “ENGINE BRAKE ADJ” in “Work
Support”.
PVIGN VOLT (V) ×Displays the backup voltage of TCM.
TRGT AUX GR RATIO Displays the target gear ratio of the auxiliary gearbox cal-
culated from processing of gear shift control.
G SEN CALIBRATION (YET/DONE) Displays the status of “G
SENSOR CALIBRATION” in
“Work Support”.
N IDLE STATUS (On/Off) Displays idle neutral status.
CVT-B • Displays CVT fluid temperature count.
• This monitor item does not use.
CVT-A • Displays CVT fluid temperature count.
• This monitor item does not use.
Monitored item
(Unit)Monitor item selection
Remarks
MAIN SIG-
NALS ECU IN-
PUT SIG-
NALS
Item name Description
ENGINE BRAKE ADJ. Although there is no malfunction on the transaxle and the CVT system, if a customer
make a complaint like “I do not feel comfortable with automatic operation of the engine
brake on downhill”, the engine brake may be cancelled with “engine brake adjust-
ment”.
CONFORM CVTF DETERIORTN Check the degradation level of the CVT fluid under severe conditions.
G SENSOR CALIBRATION Compensate the G sensor.
ERASE CALIBRATION DATA Erase the calibration data memorized by TCM.
ERASE LEARNING VALUE Erase the learning value me morized by TCM.
ERASE MEMORY DATA Perform “erasing of the calibration data” and “erasing of the learned value” at the same
time.
CLUTCH POINT LEARNING* Allow learning of the clutch engagement point of the auxiliary gearbox for TCM.
ENGINE BRAKE LEVEL
ON : Turn ON the engine brake control.
OFF : Turn OFF the engine brake control.
CVTF degradation level data
210,000 or more : Replacement of the CVT fluid is required.
Less than 210,000 : Replacement of the CVT fluid is not required.
Revision: August 2015 2016 Versa Note

cardiagn.com

TCM
TM-109
< ECU DIAGNOSIS INFORMATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Protection Control INFOID:0000000012431035
The TCM becomes the protection control status temporarily to protect the safety when the safety of TCM and
transmission is lost. It automatically returns to the normal status if the safety is secured.
The TCM has the following protection control.
CONTROL FOR WHEEL SPIN
CONTROL WHEN FLUID TEMPERATURE IS HIGH
TORQUE IS REDUCED WHEN DRIVING WITH THE REVERSE GEAR
REVERSE PROHIBIT CONTROL
DTC Inspection Priority ChartINFOID:0000000012431036
If multiple malfunction codes are detected at the same time, check each code according to the DTC check pri-
ority list below.
Control When a wheel spin is detected, the engine output and gear ratio are limited and the line pressure is increased.
At the 1GR, the clutch pressure is increased.
Vehicle behavior in
control If the accelerator is kept depressing during wheel spin, the engine revolution and vehicle speed are limited to
a certain degree. From the 1GR, upshift to a certain gear ratio is only allowed.
Normal return condi-
tion Wheel spin convergence returns the control to the normal control.
ControlWhen the CVT fluid temperature is high, the gear shift permission maximum revolution and the maximum
torque are reduced than usual to prevent increase of the oil temperature.
Vehicle behavior in
control Power performance may be lowered, compared to normal control.
Normal return condi-
tion The control returns to the normal control when CVT fluid temperature is lowered.
Control
Engine output is controlled according to a vehicle speed while reversing the vehicle.
Vehicle behavior in
control Power performance may be lowered while reversing the vehicle.
Normal return condi-
tion Torque returns to normal by positioning the selector lever in a range ot
her than “R” position.
ControlThe reverse brake is controlled to avoid becoming engaged when the selector lever is set in “R” position while
driving in forward direction at more than the specified speed.
Vehicle behavior in
control If the selector lever is put at “R” position when driving with the forward gear, the gear becomes neutral, not
reverse.
Normal return condi-
tion The control returns to normal control when the vehicle is driven at low speeds. (The reverse brake becomes
engaged.)
Priority
DTC (Diagnostic Trouble Code) Reference
1 P0863 CONTROL UNIT (CAN)
TM-181
U0073 COMM BUS A OFFTM-135
U0100 LOST COMM (ECM A)TM-136
U0140 LOST COMM (BCM)TM-137
U0141 LOST COMM (BCM A)TM-138
U0155 LOST COMM (IPC)TM-139
U0300 CAN COMM DATA TM-140
U1000 CAN COMM CIRCTM-141
U1117 LOST COMM (ABS)TM-142
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-110
< ECU DIAGNOSIS INFORMATION >[CVT: RE0F11A]
TCM
DTC Index
INFOID:0000000012431037
NOTE:
• If multiple malfunction codes are detected at the same time, check each code according to the “DTC check
priority list”. TM-109, "
DTC Inspection Priority Chart".
• The ignition counter is displayed in “FFD”. Refer to TM-93, "
CONSULT Function".
2P0740 TORQUE CONVERTER
TM-167
P0743 TORQUE CONVERTERTM-169
P0962 PC SOLENOID ATM-184
P0963 PC SOLENOID ATM-186
P0966 PC SOLENOID BTM-189
P0967 PC SOLENOID BTM-191
P0998 SHIFT SOLENOID FTM-193
P0999 SHIFT SOLENOID FTM-195
P099B SHIFT SOLENOID GTM-197
P099C SHIFT SOLENOID GTM-199
3P0890 TCM TM-182
4P062F EEPROM
TM-143
P0705 T/M RANGE SENSOR ATM-144
P0706 T/M RANGE SENSOR ATM-150
P0711 FLUID TEMP SENSOR ATM-153
P0712 FLUID TEMP SENSOR ATM-157
P0713 FLUID TEMP SENSOR ATM-159
P0715 INPUT SPEED SENSOR ATM-161
P0847 FLUID PRESS SEN/SW BTM-177
P0848 FLUID PRESS SEN/SW BTM-179
P1586 G SENSORTM-201
P1588 G SENSORTM-204
P2765 OUTPUT SPEED SENSORTM-206
5P0720 OUTPUT SPEED SENSOR TM-164
6P0746 PC SOLENOID A
TM-173
P2857 CLUTCH B PRESSURETM-209
P2858 CLUTCH A PRESSURETM-210
P2859 CLUTCH A PRESSURE TM-211
P285A CLUTCH B PRESSURETM-213
7P0744 TORQUE CONVERTER
TM-171P0846 FLUID PRESS SEN/SW BTM-175
P0965 PC SOLENOID BTM-188
PriorityDTC (Diagnostic Trouble Code) Reference
DTC*1, *2
Items
(CONSULT screen terms) Trip MILPermanent
DTC
group
*3Reference
GST CONSULT
(TRANSMISSION)
P062F P062F EEPROM 1ON B TM-143
P0705P0705 T/M RANGE SENSOR A 2ON B TM-144
P0706P0706 T/M RANGE SENSOR A 2ON B TM-150
P0711P0711 FLUID TEMP SENSOR A 2ON A TM-153
Revision: August 2015 2016 Versa Note

cardiagn.com

TCM
TM-111
< ECU DIAGNOSIS INFORMATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
*1: These numbers are specified by SAE J2012/ISO 15031-6.
*2: The DTC number of the 1st trip is the same as the DTC number.
*3: Refer to TM-134, "
Description".
P0712 P0712 FLUID TEMP SENSOR A 2ON B TM-157
P0713P0713 FLUID TEMP SENSOR A 2ON B TM-159
P0715P0715 INPUT SPEED SENSOR A 2ON B TM-161
P0720P0720 OUTPUT SPEED SENSOR 2ON B TM-164
P0740P0740 TORQUE CONVERTER 2ON B TM-167
P0743P0743 TORQUE CONVERTER 2ON B TM-169
P0744P0744 TORQUE CONVERTER 2ON B TM-171
P0746P0746 PC SOLENOID A 2ON B TM-173
P0846P0846 FLUID PRESS SEN/SW B 2ON B TM-175
P0847P0847 FLUID PRESS SEN/SW B 2ON B TM-177
P0848P0848 FLUID PRESS SEN/SW B 2ON B TM-179
P0863P0863 CONTROL UNIT (CAN) 1ON B TM-181
P0890P0890 TCM 1ON B TM-182
P0962P0962 PC SOLENOID A 2ON B TM-184
P0963P0963 PC SOLENOID A 2ON B TM-186
P0965P0965 PC SOLENOID B 2ON B TM-188
P0966P0966 PC SOLENOID B 2ON B TM-189
P0967P0967 PC SOLENOID B 2ON B TM-191
P0998P0998 SHIFT SOLENOID F 2ON B TM-193
P0999P0999 SHIFT SOLENOID F 2ON B TM-195
P099BP099B SHIFT SOLENOID G 2ON B TM-197
P099CP099C SHIFT SOLENOID G 2ON B TM-199
—P1586 G SENSOR 1— — TM-201
—P1588 G SENSOR 1— — TM-204
P2765P2765 OUTPUT SPEED SENSOR 2ON B TM-206
P2857P2857 CLUTCH A PRESSURE 2ON B TM-209
P2858P2858 CLUTCH B PRESSURE 2ON B TM-210
P2859P2859 CLUTCH A PRESSURE 2ON B TM-211
P285AP285A CLUTCH B PRESSURE 2ON B TM-213
U0073U0073 COMM BUS A OFF 1ON B TM-135
U0100U0100 LOST COMM (ECM A) 1ON B TM-136
—U0140 LOST COMM (BCM) 1— — TM-137
—U0141 LOST COMM (BCM A) 1— — TM-138
—U0155 LOST COMM (IPC) 1— — TM-139
—U0300 CAN COMM DATA 1— — TM-140
—U1000 CAN COMM CIRC 1— — TM-141
—U1117 LOST COMM (ABS) 1— — TM-142
DTC*1, *2Items
(CONSULT screen terms) Trip MILPermanent
DTC
group
*3Reference
GST CONSULT
(TRANSMISSION)
Revision: August 2015 2016 Versa Note

cardiagn.com

DIAGNOSIS AND REPAIR WORK FLOWTM-123
< BASIC INSPECTION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Use TM-223, "Symptom Table" from the symptom inspection result in step 4. Then identify where to start per-
forming the diagnosis based on possible causes and symptoms.
>> GO TO 8.
7.REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the detected malfunctioning parts.
Reconnect parts or connector after repairing or replacing, and then erase DTC if necessary.
>> GO TO 8.
8.FINAL CHECK
Perform “DTC CONFIRMATION PROCEDURE” again to make sure that the repair is correctly performed.
Check that malfunctions are not reproduced when obtai ning the malfunction information from the customer,
referring to the symptom inspection result in step 3 or 4.
Is DTC or malfunction symptom reproduced?
YES-1 (DTC is reproduced.)>>GO TO 5.
YES-2 (Malfunction is reproduced.)>>GO TO 6.
NO >> Before delivering the vehicle to the customer, make sure that DTC is erased.
Question sheetINFOID:0000000012431041
DESCRIPTION
There are many operating conditions that may cause a malfunction
of the transmission parts. By understanding those conditions prop-
erly, a quick and exact diagnosis can be achieved.
In general, perception of a problem varies depending on individuals.
Ask the customer about his/her concer ns carefully. It is important to
understand the phenomenon or status. To systemize all the informa-
tion for the diagnosis, prepare the question sheet referring to the
question points.
In some cases, multiple conditions that appear simultaneously may
cause a DTC to be detected.
Worksheet Sample
SEF907L
Question sheet
Customer's
name MR/MSRegistration
number
Initial year
registrationYear Month
day
Vehicle type Chassis No.
Storage date Ye a r M o n t h
dayEngine
Mileagekm
Symptom † Vehicle does not start. ( † R position † D position † L position † M position)
† Upshifting does not occur. † Downshifting does not occur.
† Lock-up malfunction
† Shift point is too high. † Shift point is too low.
† Shift shock ( † N ⇒D † Lock-up † R, D, L and M position)
† Slip ( † N ⇒D † Lock-up † R, D, L and M position)
† Noise † Vibration
When selector lever position is shifted, shift pattern does not change.
† Other
( )
First occurrence †Recently (as from month of year )
Frequency of occurrence †Always †Under certain conditions † Sometimes ( time(s)/day)
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-124
< BASIC INSPECTION >[CVT: RE0F11A]
DIAGNOSIS AND REPAIR WORK FLOW
Climate con-
ditionsIrrelevant
Weather †Clear †Cloud †Rain †Snow †Others )
Temperature †Hot †Warm †Cool †Cold †Temperature (Approx. °C)
Relative humidity †High †Moderate †Low
Transaxle condition † In cold-start † During warm-up (approx. °C) † After warm-up
† Engine speed: rpm
Road conditions †
Urban area † Suburb area † Highway
† Mountainous road (uphill or downhill)
Operating condition, etc. Irrelevant
† When engine starts †During idling
† During driving †During acceleration
† At constant speed driving †During deceleration
† During cornering (RH curve or LH curve)
Other conditions Question sheet
Customer's
name MR/MSRegistration
number
Initial year
registrationYe a r M o n t h
day
Vehicle type Chassis No.
Storage date Year Month
dayEngine
Mileagekm
Revision: August 2015 2016 Versa Note

cardiagn.com

ADDITIONAL SERVICE WHEN REPLACING TCMTM-125
< BASIC INSPECTION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
ADDITIONAL SERVICE WHEN REPLACING TCM
DescriptionINFOID:0000000012431042
When replacing the TCM, perform the following work. For work procedure, refer to TM-125, "Work Procedure".
TCM PROGRAMMING• Since vehicle specifications are not yet written in a new TCM, it is necessary to write them with CONSULT.
CAUTION:
When replacing TCM, save TCM data on CONSULT before removing TCM.
LOADING AND STORING OF CALIBRATION DATA• The TCM acquires calibration data (individual characteristic value) of each solenoid that is stored in the
ROM assembly (in the control valve). This enables the TCM to perform accurate control. After the TCM is
replaced, check that the calibrati on data is correctly loaded and stored.
CALIBRATION OF G SENSOR
• TCM stores calibration data (inherent characteristic value) of G sensor to provide accurate control. There-
fore, it is required to perform calibration of G sensor after the replacement of TCM.
CAUTION:
When replacing TCM and transaxle assembly simultaneously, replace transaxle assembly first and
then replace TCM.
Work ProcedureINFOID:0000000012431043
1.CHECK NEW TCM PART NUMBER
Check new TCM part number to see whether it is blank TCM or not.
NOTE:
• Part number of blank TCM is 310F6-XXXXX.
• Check the part number when ordering TCM or with the one included in the label on the container box.
Is the new TCM a blank TCM?
YES >> GO TO 2.
NO >> GO TO 3.
2.SAVING TCM DATA (VEHICLE SPECIFICATIONS)
NOTE:
Save necessary data stored in TCM in CONSULT according to the following instructions: With CONSULT
1. Turn ignition switch OFF.
2. Turn ignition switch ON.
3. Select “Re/programming, Configuration”.
4. Select “AT/CVT”.
NOTE:
If “AT/CVT” is not displayed and TCM data cannot be saved on CONSULT, GO TO 3.
5. Select “Programming”.
6. Save TCM data on CONSULT according to the CONSULT display.
>> GO TO 3.
3.REPLACE TCM
1. Turn ignition switch OFF and wait for 10 seconds.
2. Replace TCM. Refer to TM-239, "
Removal and Installation".
>> GO TO 4.
4.LOAD CALIBRATION DATA
1. Shift the selector lever to the “P” position.
2. Turn ignition switch ON.
3. Check that "P" is displayed on shift position indicator on combination meter. NOTE:
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-126
< BASIC INSPECTION >[CVT: RE0F11A]
ADDITIONAL SERVICE WHEN REPLACING TCM
Displayed approximately 4 – 5 seconds after the
selector lever is moved to the “P” position.
Does the shift position indicator display
“P”?
YES >> GO TO 5.
NO >> GO TO 8.
5.STORE CALIBRATION DATA
1. Turn ignition switch OFF and wait for 5 seconds.
2. Turn ignition switch ON.
Does the shift position indicator display
“P” at the same time when turning ON the ignition switch?
YES-1 (New TCM is blank)>>GO TO 6.
YES-2 (New TCM is not blank)>>GO TO 7.
NO >> Check harness between battery and TCM harness connector terminal. Refer to TM-182, "
Diagno-
sis Procedure".
6.WRITE TCM DATA (VEHICLE SPECIFICATIONS)
NOTE:
Write data saved in CONSULT into a new TCM according to the following instructions: With CONSULT
1. Select “Programming”.
2. Perform programming according to the CONSULT display.
>> GO TO 7.
7.CALIBRATE G SENSOR
Refer to TM-130, "
Description".
>> WORK END
8.DETECT MALFUNCTIONING ITEM
Check the following items:
• Harness between the TCM and the ROM assembly insi de the transaxle assembly is open or shorted.
• Disconnected, loose, bent, collapsed, or otherwise abnormal connector housing terminals
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace the malfunctioning parts.
Revision: August 2015 2016 Versa Note

cardiagn.com