2016 NISSAN NOTE sensor

FUEL PUMPEC-449
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
Is the inspection result normal?
YES >> GO TO 6.
NO >> GO TO 4.
4.CHECK FUSE
1. Turn ignition switch OFF.
2. Disconnect 15 A fuse (No. 48) from IPDM E/R.
3. Check 15 A fuse.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace 15 A fuse.
5.CHECK FUEL PUMP POWER SUPPLY CIRCUIT-IV
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R harness connector.
3. Check the continuity between IP DM E/R harness connector and “fuel level sensor unit and fuel pump”
harness connector.
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair open circuit, short to ground or short to power in harness or connectors.
6.CHECK FUEL PUMP GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Check the continuity between “fuel level sens or unit and fuel pump” harness connector and ground.
3. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair open circuit or short to power in harness or connectors.
7.CHECK FUEL PUMP
Refer to EC-450, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 8.
NO >> Replace “fuel level sensor unit and fuel pump”.Refer to FL-6, "
Exploded View".
8.CHECK INTERMITTENT INCIDENT
Check intermittent incident. Refer to GI-42, "
Intermittent Incident".
Fuel level sensor unit
and fuel pump Ground Voltage
Connector Terminal
B44 1 Ground Battery voltage should for exist 1 second
after ignition switch is turn ON.
IPDM E/R
Fuel level sensor unit
and fuel pump Continuity
Connector Terminal Connector Terminal
E44 9 B44 1 Existed
Fuel level sensor unit and fuel pump
Ground Continuity
Connector Terminal
B44 3 Ground Existed
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-450
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
FUEL PUMP
Is the inspection result normal?
YES >> Replace IPDM E/R. Refer to
PCS-30, "Removal and Installation".
NO >> Repair open circuit, short to ground or short to power in harness or connectors.
Component InspectionINFOID:0000000012431653
1.CHECK FUEL PUMP
1. Turn ignition switch OFF.
2. Disconnect “fuel level sensor uni t and fuel pump” harness connector.
3. Check resistance between “fuel level sensor unit and fuel pump” terminals as follows.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace “fuel level sensor unit and fuel pump”. Refer to FL-6, "
Exploded View".
TerminalsResistance [at 25°C (77 °F)]
1 and 3 0.2 - 5.0 Ω
Revision: August 2015 2016 Versa Note

cardiagn.com

ON BOARD REFUELING VAPOR RECOVERY (ORVR)EC-457
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
ON BOARD REFUELING VAPOR RECOVERY (ORVR)
Component Function CheckINFOID:0000000012431660
1.CHECK ORVR FUNCTION
Check whether the following symptoms are present.
• Fuel odor from EVAP canister is strong.
• Cannot refuel/Fuel odor from the fuel filler opening is strong while refueling.
Is any symptom present?
YES >> Go to EC-457, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012431661
1.INSPECTION START
Check whether the following symptoms are present.
A: Fuel odor from EVAP canister is strong.
B: Cannot refuel/Fuel odor from the fuel filler opening is strong while refueling.
Which symptom is present?
A >> GO TO 2.
B >> GO TO 8.
2.CHECK EVAP CANISTER
1. Remove EVAP canister with EVAP canister vent c ontrol valve and EVAP control system pressure sensor
attached.
2. Weigh the EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor
attached.
The weight should be l ess than 1.6 kg (3.5 lb).
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 4.
3.CHECK IF EVAP CANISTER IS SATURATED WITH WATER
Check if water will drain from EVAP canister.
Does water drain from the EVAP canister?
YES >> GO TO 4.
NO >> GO TO 7.
4.REPLACE EVAP CANISTER
Replace EVAP canister with a new one.
>> GO TO 5.
5.CHECK DRAIN FILTER
Refer to EC-461, "
Component Inspection (Drain filter)".
Is the inspection result normal?
OK >> GO TO 6.
NO >> Replace drain filter.
6.DETECT MALFUNCTIONING PART
PBIB1213E
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-458
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
ON BOARD REFUELING VAPOR RECOVERY (ORVR)
Check the EVAP hose between EVAP canister and
vehicle frame for clogging or poor connection.
>> Repair or replace EVAP hose.
7.CHECK REFUELING EVAP VAPOR CUT VALVE
Refer to EC-459, "
Component Inspection (Refueli ng EVAP vapor cut valve)".
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace refueling EVAP vapor cut valve with fuel tank.
8.CHECK EVAP CANISTER
1. Remove EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor attached.
2. Weigh the EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor
attached.
The weight should be l ess than 1.6 kg (3.5 lb).
Is the inspection result normal?
YES >> GO TO 9.
NO >> GO TO 10.
9.CHECK IF EVAP CANISTER IS SATURATED WITH WATER
Check if water will drain from EVAP canister.
Does water drain from the EVAP canister?
YES >> GO TO 10.
NO >> GO TO 13.
10.REPLACE EVAP CANISTER
Replace EVAP canister with a new one.
>> GO TO 11.
11 .CHECK DRAIN FILTER
Refer to EC-461, "
Component Inspection (Drain filter)".
Is the inspection result normal?
OK >> GO TO 12.
NO >> Replace drain filter.
12.DETECT MALFUNCTIONING PART
Check the EVAP hose between EVAP canister and vehicle frame for clogging or poor connection.
>> Repair or replace EVAP hose.
13.CHECK VENT HOSES AND VENT TUBES
Check hoses and tubes between EVAP canister and refueling control valve for clogging, kink, looseness and
improper connection.
Is the inspection result normal?
YES >> GO TO 14.
NO >> Repair or replace hoses and tubes.
14.CHECK RECIRCULATION LINE
PBIB1213E
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-462
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
REFRIGERANT PRESSURE SENSOR
REFRIGERANT PRESSURE SENSOR
Component Function CheckINFOID:0000000012431664
1.CHECK REFRIGERANT PRESSURE SENSOR OVERALL FUNCTION
1. Start engine and warm it up to normal operating temperature.
2. Turn A/C switch and blower fan switch ON.
3. Check the voltage between ECM harness connector and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Go to EC-462, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012431665
1.CHECK GROUND CONNECTION
1. Turn A/C switch and blower fan switch OFF.
2. Stop engine.
3. Turn ignition switch OFF.
4. Check ground connection E15. Refer to Ground Inspection in GI-44, "
Circuit Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace ground connection.
2.CHECK REFRIGERANT PRESSURE SENSOR POWER SUPPLY CIRCUIT
1. Disconnect refrigerant pressure sensor harness connector.
2. Turn ignition switch ON.
3. Check the voltage between refrigerant pressure sensor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 3.
3.DETECT MALFUNCTIONING PART
Check the following.
• Harness for open or short between ECM and refrigerant pressure sensor
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.CHECK REFRIGERANT PRESSURE SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between refrigerant pre ssure sensor harness connector and ECM harness connec-
tor.
ECM
Vol tag e
Connector Te r m i n a l
+ −
E16 101
(Refrigerant pressure sensor signal) 98 1.0 - 4.0V
Refrigerant pressure sensor
Ground Voltage
Connector Terminal
E17 3Ground Approx. 5 V
Revision: August 2015 2016 Versa Note

cardiagn.com

REFRIGERANT PRESSURE SENSOREC-463
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 6.
NO >> GO TO 5.
5.DETECT MALFUNCTIONING PART
Check the following.
• Harness for open or short between ECM and refrigerant pressure sensor
>> Repair open circuit or short to ground or short to power in harness or connectors.
6.CHECK REFRIGERANT PRESSURE SENSOR IN PUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Check the continuity between ECM harness connecto r and refrigerant pressure sensor harness connec-
tor.
2. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 8.
NO >> GO TO 7.
7.DETECT MALFUNCTIONING PART
Check the following.
• Harness for open or short between ECM and refrigerant pressure sensor
>> Repair open circuit or short to ground or short to power in harness or connectors.
8.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace refrigerant pressure sensor. Refer to HA-32, "REFRIGERANT PRESSURE SENSOR :
Removal and Installation".
NO >> Repair or replace.
Refrigerant pressure sensor ECM
Continuity
Connector Terminal Connector Terminal
E17 1E16 98 Existed
Refrigerant pressure sensor ECM
Continuity
Connector Terminal Connector Terminal
E17 2E16 85 Existed
Revision: August 2015 2016 Versa Note

cardiagn.com

ENGINE CONTROL SYSTEM SYMPTOMSEC-465
< SYMPTOM DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
Mass air flow sensor circuit
1
12 2
222 2 EC-190, "DTC Log-
ic"
Engine coolant temperature sensor
circuit
333
EC-201, "DTC Log-
ic"
Air fuel ratio (A/F
) sensor 1 circuit EC-213, "
DTC Log-
ic"
EC-217, "DTC Log-
ic"
EC-220, "DTC Log-
ic"
EC-243, "DTC Log-
ic"
EC-398, "DTC Log-
ic"
Throttle position sensor circuit
22EC-203, "
DTC Log-
ic"
EC-267, "DTC Log-
ic"
EC-369, "DTC Log-
ic"
EC-370, "DTC Log-
ic"
EC-419, "DTC Log-
ic"
Accelerator pedal position sensor cir-
cuit
321 EC-413, "
DTC Log-
ic"
EC-416, "DTC Log-
ic"
EC-422, "DTC Log-
ic"
Heated oxygen sensor 2 circuit
6 6 6 65EC-223, "
DTC Log-
ic"
EC-229, "DTC Log-
ic"
EC-237, "DTC Log-
ic"
Knock sensor circuit
23EC-276, "DTC Log-
ic"
Engine oil temperature sensor circuit
4 23EC-265, "DTC Log-
ic"
Engine oil pressure sensor circuit
4 4 3 3 33EC-339, "DTC Log-
ic"
SYMPTOM
Reference page
HARD/NO START/RESTART (EXCP. HA)
ENGINE STALL
HESITATION/SURGING/FLAT SPOT
SPARK KNOCK/DETONATION
LACK OF POWER/POOR ACCELERATION
HIGH IDLE/LOW IDLE
ROUGH IDLE/HUNTING
IDLING VIBRATION
SLOW/NO RETURN TO IDLE
OVERHEATS/WATER TEMPERATURE HIGH
EXCESSIVE FUEL CONSUMPTION
EXCESSIVE OIL CONSUMPTION
BATTERY DEAD (UNDER CHARGE)
Warranty symptom codeAA AB AC AD AE AF AG AH AJ AK AL AM HA
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-466
< SYMPTOM DIAGNOSIS >[HR16DE]
ENGINE CONTROL SYSTEM SYMPTOMS
1 - 6: The numbers refer to the order of inspection.
(continued on next table)
SYSTEM — ENGINE MECHANICAL & OTHER
Crankshaft position sensor circuit 2 2 EC-278, "DTC Log-
ic"
Camshaft position sensor circuit 3 2EC-282, "DTC Log-
ic"
Vehicle speed signal circuit
2 3 3 3EC-332, "DTC Log-
ic"
ECM
22333333333 —
Intake valve timing control solenoid
valve circuit 32 13223 3
EC-167, "
DTC Log-
ic"
Exhaust valve timing control solenoid
valve circuit32 13223 3 EC-171, "DTC Log-
ic"
PNP signal circuit
3 3 3 33EC-358, "DTC Log-
ic"
Refrigerant pressure sensor circuit 2
33 4 EC-462, "Diagnosis
Procedure"
Electrical load signal circuit
3EC-444, "Diagnosis
Procedure"
Air conditioner circuit
223333333 3 2 HAC-28, "Workflow"
ABS actuator and electric unit (con-
trol unit)4 BRC-52, "Work
Flow"
SYMPTOM
Reference page
HARD/NO START/RESTART (EXCP. HA)
ENGINE STALL
HESITATION/SURGING/FLAT SPOT
SPARK KNOCK/DETONATION
LACK OF POWER/POOR ACCELERATION
HIGH IDLE/LOW IDLE
ROUGH IDLE/HUNTING
IDLING VIBRATION
SLOW/NO RETURN TO IDLE
OVERHEATS/WATER TEMPERATURE HIGH
EXCESSIVE FUEL CONSUMPTION
EXCESSIVE OIL CONSUMPTION
BATTERY DEAD (UNDER CHARGE)
Warranty symptom codeAA AB AC AD AE AF AG AH AJ AK AL AM HA
Revision: August 2015 2016 Versa Note

cardiagn.com