2014 NISSAN TEANA reset

BCS
DIAGNOSIS SYSTEM (BCM)BCS-23
< SYSTEM DESCRIPTION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
ACTIVE TEST
DOOR STAT -AS [LOCK/READY/UNLK]
×Indicates condition of passenger side door status.
DOOR STAT -RR [LOCK/READY/UNLK] ×Indicates condition of rear right side door status.
DOOR STAT -RL [LOCK/READY/UNLK] ×Indicates condition of rear left side door status.
ID OK FLAG [Set/Reset] Indicates condition of Intelligent Key ID.
PRMT ENG STRT [Set/Reset] Indicates condition of engine start possibility.
PRMT RKE STRT [Set/Reset] Indicates condition of engine start possibility from Intelligent Key.
I-KEY OK FLAG [Key ON/Key OFF] ×Indicates condition of Intelligent Key OK flag.
PRBT ENG STRT [Set/Reset] Indicates condition of engine start prohibit.
ID AUTHENT CANCEL TIMER [STOP] Indicates condition of Intelligent Key ID authentication.
ACC BATTERY SAVER [STOP] Indicate s condition of battery saver.
CRNK PRBT TMR [On/Off] In dicates condition of crank prohibit timer.
AUT CRNK TMR [On/Off] Indicates condition of automatic engine crank timer from Intelligent Key.
CRNK PRBT TME [sec] I ndicates condition of engine crank prohibit time.
AUTO CRNK TME [sec] Indicates co ndition of automatic engine crank time from Intelligent Key.
CRANKING TME [sec] Indicates condition of engine cranking time from Intelligent Key.
DETE SW PWR [On/Off] Indicates condition of detent switch voltage.
ACC RLY -REQ [On/Off] Indicates condition of accessory relay control request.
RKE OPE COUN1 [0-19] ×When remote keyless entry receiver receives the signal transmitted while
operating on Intelligent Key, the numerical value start changing.
RKE OPE COUN2 [0-19] ×When remote keyless entry receiver receives the signal transmitted while
operating on Intelligent Key, the numerical value start changing.
TRNK/HAT MNTR [On/Off] Indicates condition of trunk room lamp switch.
RKE-LOCK [On/Off] Indicates condition of lock signal from Intelligent Key.
RKE-UNLOCK [On/Off] Indicates condition of unlock signal from Intelligent Key.
RKE-TR/BD [On/Off] Indicates condition of trunk open signal from Intelligent Key.
RKE-PANIC [On/Off] Indicates condition of panic signal from Intelligent Key.
RKE-MODE CHG [On/Off] Indicates condition of mode change signal from Intelligent Key. Monitor Item [Unit] Main Description
Test Item Description
INTELLIGENT KEY LINK (CAN) This test is able to check Intelligent Key iden
tification number [Off/ID No1/ID N02/ID No3/ID
No4/ID No5].
INT LAMP This test is able to check interior room lamp operation [On/Off].
FLASHER This test is able to check hazard lamp operation [LH/RH/Off].
HORN This test is able to check horn operation [On].
BATTERY SAVER This test is able to check battery saver operation [On/Off].
TRUNK/BACK DOOR This test is able to check trunk actuator operation [Open].
OUTSIDE BUZZER This test is able to check In telligent Key warning buzzer operation [On/Off].
INSIDE BUZZER This test is able to check combination meter warning chime operation [Take Out/Knob/Key/
Off].
INDICATOR This test is able to check combination meter warning lamp operation [KEY ON/KEY IND/Off].
IGN CONT2 This test is able to check ignition relay-2 control operation [On/Off].
ENGINE SW ILLUMI This test is able to check push-bu tton ignition switch START indicator operation [On/Off].
PUSH SWITCH INDICATOR This test is able to check push-button ignition switch indicator operation [On/Off].
ACC CONT This test is able to check ac cessory relay control operation [On/Off].
IGN CONT1 This test is able to check ignition relay-1 control operation [On/Off].
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS-26
< SYSTEM DESCRIPTION >[BCM]
DIAGNOSIS SYSTEM (BCM)
CONFIGURATION
Refer to
BCS-65, "CONFIGURATION (BCM) : Description".
CAN DIAG SUPPORT MNTR
Refer to LAN-15, "CAN Diagnostic Support Monitor".
IMMU
IMMU : CONSULT Function (BCM - IMMU)INFOID:0000000009462009
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF → ON (for at least 5 seconds) → OFF. If this step is not performed, the BCM may not go
to ”sleep mode”, potentially causing a di scharged battery and a no-start condition.
SELF DIAGNOSTIC RESULT
Refer to BCS-52, "DTC Index".
DATA MONITOR
ACTIVE TEST
BATTERY SAVER
BATTERY SAVER : CONSULT Func tion (BCM - BATTERY SAVER)INFOID:0000000009462010
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF → ON (for at least 5 seconds) → OFF. If this step is not performed, the BCM may not go
to ”sleep mode”, potentially causing a di scharged battery and a no-start condition.
DATA MONITOR
Support Item Setting Description
RESET SETTING VALUE Reset Returns BCM to initial value in factory shipment.
Cancel Cancels the reset function.
Monitor Item [Unit] Description
CONFRM ID ALL [Yet/DONE]
Switches to DONE when an Intelligent Key is registered.
CONFIRM ID4 [Yet/DONE]
CONFIRM ID3 [Yet/DONE]
CONFIRM ID2 [Yet/DONE]
CONFIRM ID1 [Yet/DONE]
TP 4 [Yet/DONE]
DONE indicates the number of Intelligent Key ID which has been registered.
TP 3 [Yet/DONE]
TP 2 [Yet/DONE]
TP 1 [Yet/DONE]
PUSH SW [On/Off] Indicates condition of push-button ignition switch.
Test Item Description
THEFT IND This test is able to check security indicator operation [On/Off].
Monitor Item [Unit] Description
REQ SW -DR [On/Off] Indicates condition of door request switch LH.
REQ SW -AS [On/Off] Indicates condition of door request switch RH.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS
BCM (BODY CONTROL MODULE)BCS-33
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
FR WASHER SW
Front washer switch OFF Off
Front washer switch ON On
FR WIPER LOW Front wiper switch OFF Off
Front wiper switch LO On
FR WIPER HI Front wiper switch OFF Off
Front wiper switch HI On
FR WIPER INT Front wiper switch OFF Off
Front wiper switch INT On
FR WIPER STOP Any position other than front wiper stop position Off
Front wiper stop position On
HAZARD SW When hazard switch is not pressed Off
When hazard switch is pressed On
HEAD LAMP SW 1 Headlamp switch OFF Off
Headlamp switch 1st On
HEAD LAMP SW 2 Headlamp switch OFF Off
Headlamp switch 1st On
HI BEAM SW High beam switch OFF Off
High beam switch HI On
ID AUTHENT CANCEL TIMER When I-Key authentication is OFF. STOP
ID OK FLAG Ignition switch ACC or ON Reset
Ignition switch OFF Set
ID REGST FL1 ID registration of front left tire incomplete YET
ID registration of front left tire complete DONE
ID REGST FR1 ID registration of front right tire incomplete YET
ID registration of front right tire complete DONE
ID REGST RL1 ID registration of rear left tire incomplete YET
ID registration of rear left tire complete DONE
ID REGST RR1 ID registration of rear
right tire incomplete YET
ID registration of rear right tire complete DONE
IGN RLY1 F/B Ignition switch OFF or ACC Off
Ignition switch ON On
INT VOLUME Wiper intermittent dial is in a dial position 1 - 7 1 - 7
I-KEY OK FLAG I-Key OFF Key OFF
I-Key ON Key ON
KEY CYL LK-SW Door key cylinder LOCK position Off
Door key cylinder other than LOCK position On
KEY CYL UN-SW Door key cylinder UNLOCK position Off
Door key cylinder other than UNLOCK position On
OPTI SEN (DTCT) Bright outside of the vehicle Close to 5V
Dark outside of the vehicle Close to 0V
OPTI SEN (FILT) Bright outside of the vehicle Close to 5V
Dark outside of the vehicle Close to 0V
PA S S I N G S W Other than lighting switch PASS Off
Lighting switch PASS On
Monitor Item Condition Value/Status
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS-34
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
PRBT ENG STRTWhen the engine start is prohibited Reset
When the engine start is permitted Set
PRMT ENG STRT When the engine start is prohibited Reset
When the engine start is permitted Set
PRMT RKE STRT When the engine start is prohibited Reset
When the engine start is permitted Set
PUSH SW Return ignition switch to LOCK position Off
Press ignition switch On
PUSH SW-IPDM When engine switch (push switch) is not pressed Off
When engine switch (push switch) is pressed On
REAR DEF SW Rear window defogger switch OFF Off
Rear window defogger switch ON On
REQ SW-AS When passenger door request switch is not pressed Off
When passenger door request switch is pressed On
REQ SW-DR When driver door request switch is not pressed Off
When driver door request switch is pressed On
REQ SW-BD/TR When trunk opener request switch is not pressed Off
When trunk opener request switch is pressed On
RKE-LOCK When LOCK button of Intelligent Key is not pressed Off
When LOCK button of Intelligent Key is pressed On
RKE-MODE CHG When LOCK/UNLOCK button of Intelligent Key is not pressed and
held simultaneously Off
When LOCK/UNLOCK button of Intelligent Key is pressed and held
simultaneously On
RKE OPE COUN1 Operation frequency of Intelligent Key 0-19
RKE OPE COUN2 Operation frequency of Intelligent Key 0-19
RKE-PANIC When PANIC button of Intelligent Key is not pressed Off
When PANIC button of Intelligent Key is pressed On
RKE-P/W OPEN When UNLOCK button of Intelligent Key is not pressed and held Off
When UNLOCK button of Intelligent Key is pressed and held On
RKE-TR/BD When TRUNK OPEN button of Intelligent Key is not pressed Off
When TRUNK OPEN button of Intelligent Key is pressed On
RKE-UNLOCK When UNLOCK button of Intelligent Key is not pressed Off
When UNLOCK button of Intelligent Key is pressed On
SFT N-MET When selector lever is in any position other than N Off
When selector lever is in N position On
SFT P-MET When selector lever is in any position other than P Off
When selector lever is in P position On
SFT PN -IPDM When selector lever is in any position other than P or N Off
When selector lever is in P or N position On
SFT PN/N SW When selector lever is in any position other than P or N Off
When selector lever is in P or N position On
SHFTLCK SLNID PER SPLY When BCM is not supplying power to shiftlock. Off
When BCM is supplying power to shiftlock. On
Monitor Item Condition Value/Status
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS
COMBINATION SWITCHBCS-81
< REMOVAL AND INSTALLATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
COMBINATION SWITCH
Exploded ViewINFOID:0000000009462045
NOTE:
Shown with the steering wheel removed for clarity only.
Removal and InstallationINFOID:0000000009462046
REMOVAL
CAUTION:
• Before servicing, turn the ignition switch OFF, disconnect both battery terminals and wait at least
three minutes.
• Do not use air tools or electric tools for servicing.
1. Disconnect both the negative and positive battery terminal s, then wait at least three minutes. Refer to PG-
73, "Removal and Installation (Battery)".
2. Remove the steering column covers. Refer to IP-17, "Removal and Installation"
.
3. Rotate steering wheel clockwise to access first combination switch bolt and remove.
4. Rotate steering wheel counter-clockwise to access second combination switch bolt and remove.
5. Disconnect the harness connector from the combination switch and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After the work is completed, make sure no system malfunction is detected by air bag warning lamp.
• In case a malfunction is detected by the air bag wa rning lamp, reset with the self-diagnosis function
and delete the memory with CONSULT.
• If a malfunction is still detected after the above operation, perform self-diagnosis to repair malfunc-
tions. Refer to SRC-42, "ADDITIONAL SERVICE WHEN RE PLACING CONTROL UNIT : Special Repair
Requirement".
AWMIA1293ZZ
1. Combination switch 2. Combination switch harness connector Front
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BRC-64
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1101, C1102, C1103,
C1104 WHEEL SENSOR
DTC/CIRCUIT DIAGNOSIS
C1101, C1102, C1103, C1104 WHEEL SENSOR
DTC LogicINFOID:0000000009463770
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF DIAGNOSTIC RESULT
With CONSULT.
1. Start engine and drive vehicle at approximately 21 km/h (13 MPH) or more for approximately 5 minutes.
2. Perform self diagnostic result.
Is DTC C1101, C1102, C1103 or C1104 detected?
YES >> Proceed to diagnosis procedure. Refer to BRC-64, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis ProcedureINFOID:0000000009463771
Regarding Wiring Diagram information, refer to BRC-47, "Wiring Diagram".
CAUTION:
Do not check between wheel sensor terminals.
1.CONFIRM DTC
With CONSULT
1. Perform self-diagnostic result of ABS and record all active DTCs.
2. Clear all DTCs.
3. Perform DTC confirmation procedure. Refer to BRC-64, "DTC Logic"
.
Does DTC C1101, C1102, C1103 or C1104 reset?
YES >> GO TO 2.
NO >> Refer to GI-43, "Intermittent Incident"
.
2.INSPECT WHEEL SENSOR
Inspect the suspect wheel sensor for damage or deformation.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace as necessary.
DTC Display Item Malfunction detected condition Possible causes
C1101 RR RH SENSOR-1 • When power supply voltage of rear wheel sensor
RH is low.
• When an open or shorted circuit is detected in rear
wheel sensor RH circuit.
• Harness or connector
• Wheel sensor
• ABS actuator and electric unit
(control unit)
C1102 RR LH SENSOR-1
• When power supply voltage of rear wheel sensor
LH is low.
• When an open or shorted circuit is detected in rear
wheel sensor LH circuit.
C1103 FR RH SENSOR-1 • When power supply voltage of front wheel sensor
RH is low.
• When an open or shorted circuit is detected in front
wheel sensor RH circuit.
C1104 FR LH SENSOR-1 • When power supply voltage of front wheel sensor
LH is low.
• When an open or shorted circuit is detected in front wheel sensor LH circuit.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

C1101, C1102, C1103, C1104 WHEEL SENSOR
BRC-67
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
Is the inspection result normal?
YES >> GO TO 10.
NO >> Check the following:
• 10A fuse No. 49 located in the IPDM E/R
• Harness between ABS actuator and electr ic unit (control unit) and IPDM E/R
10.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between ABS actuator and elec tric unit (control unit) connector E54 terminals and
ground.
Is the inspection result normal?
YES >> GO TO 11.
NO >> Repair or replace malfunctioning components.
11 .CHECK WHEEL SENSOR INPUT VOLTAGE
1. Connect ABS actuator and electric unit (control unit) connector E54.
2. Turn ignition switch ON.
3. Check voltage between suspect wheel sensor harness connector terminals.
Is the inspection result normal?
YES >> Replace wheel sensor. Refer to BRC-124, "Removal and Installation - Front Wheel Sensor" or
BRC-125, "Removal and Installation - Rear Wheel Sensor"
. Then, GO TO 12.
NO >> Replace ABS actuator and electric unit (control unit). Refer to BRC-128, "Removal and Installa-
tion".
12.CONFIRM REPAIR
With CONSULT
1. Clear all DTCs.
2. Perform DTC confirmation procedure. Refer to BRC-64, "DTC Logic"
.
Does DTC C1101, C1102, C1103 or C1104 reset?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-128, "Removal and Installa-
tion".
NO >> Inspection End.
ABS actuator and electric unit
(control unit) Ground Condition Vo l ta g e
(Approx.)
Connector Terminal
E54 28 — Ignition switch ON Battery voltage
Ignition switch OFF 0V
ABS actuator and electric unit (control unit) —Continuity
Connector Terminal
E54 13
Ground Yes
38
Wheel Sensor (+) (-) Voltage
(Approx.)
Wheel Connector Terminal Terminal
Front LH E19
1 2 Battery voltage
Front RH E41
Rear LH C2
Rear RH C3
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BRC-68
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1105, C1106, C1107,
C1108 WHEEL SENSOR
C1105, C1106, C1107, C1108 WHEEL SENSOR
DTC LogicINFOID:0000000009463772
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF DIAGNOSTIC RESULT
With CONSULT.
1. Start engine and drive vehicle at approximately 21 km/h (13 MPH) or more for approximately 5 minutes.
2. Perform self diagnostic result.
Is DTC C1105, C1106, C1107 or C1108 detected?
YES >> Proceed to diagnosis procedure. Refer to BRC-68, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis ProcedureINFOID:0000000009463773
Regarding Wiring Diagram information, refer to BRC-47, "Wiring Diagram".
CAUTION:
Do not check between wheel sensor terminals.
1.CONFIRM DTC
With CONSULT
1. Perform self-diagnostic result of ABS and record all active DTCs.
2. Clear all DTCs.
3. Perform DTC confirmation procedure. Refer to BRC-68, "DTC Logic"
.
Does DTC C1105, C1106, C1107 or C1108 reset?
YES >> GO TO 2.
NO >> Refer to GI-43, "Intermittent Incident"
.
2.CHECK TIRE PRESSURE AND TIRE WEAR
Check tires for excessive wear and proper inflation. Refer to WT-53, "Inspection"
.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace as necessary.
3.CHECK WHEEL SENSOR
DTC Display Item Malfunction detected condition Possible causes
C1105 RR RH SENSOR-2 • When distance between rear wheel sensor RH and
rear wheel sensor RH rotor is large.
• When installation of rear wheel sensor RH or rear wheel sensor RH rotor is not normal.
• Wheel sensor
• ABS actuator and electric unit
(control unit)
• Sensor rotor
C1106 RR LH SENSOR-2
• When distance between rear wheel sensor LH and
rear wheel sensor LH rotor is large.
• When installation of rear wheel sensor LH or rear wheel sensor LH rotor is not normal.
C1107 FR RH SENSOR-2 • When distance between front wheel sensor RH
and front wheel sensor RH rotor is large.
• When installation of front wheel sensor RH or front wheel sensor RH rotor is not normal.
C1108 FR LH SENSOR-2 • When distance between front wheel sensor LH and
front wheel sensor LH rotor is large.
• When installation of front wheel sensor LH or front wheel sensor LH rotor is not normal.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM