2014 MITSUBISHI OUTLANDER SPORT Lock control

Electric window control
Locking and unlocking 4-29
4
1. The inside alarm will be activated forapproximately 10 seconds. (except forvehicles equipped with the interior alarmsensor)2. The alarm will be activated for approxi-mately 30 seconds.The turn-signal lamps will flash, and thehorn (the siren for vehicles equipped withthe interior alarm sensor) will sound inter-mittently.3. The alarm will resume if unlawful actionsare taken again, even if the alarm hasstopped.
E00302001698
It is possible to halt the activation of an alarmusing the following methods:zPressing the LOCK or UNLOCK switchon the remote control switch.(After pressing of the LOCK switch, thevehicle will lock if all the doors and thetailgate are closed, after which the systempreparation mode will once again go intoeffect.)zPutting the operation mode in ON.zHolding the keyless operation key andlocking or unlocking the doors and thetailgate using the keyless operation func-tion.
E00302201632
The electric windows can only be operatedwith the operation mode in ON.
E00302301822
Each door window opens or closes while thecorresponding switch is operated.
NOTE
zIf the bonnet is opened during the systemarmed mode, the vehicl
e outside alarm oper-
ates immediately.
Cancelling the alarm

NOTE
zWhen the ignition switch is turned to the“ON” position or the operation mode is putin ON, the buzzer sounds 4 times. This oper-ation indicates that the alarm was activatedwhile the vehicle was parked.Please check the inside of the vehicle to con-firm that nothi
ng was stolen.
zEven if the battery is disconnected, the alarmactivation memory will not be erased.
Electric window control Electric window control switch 1- Driver’s door window2- Front passenger’s door window3- Rear left door window4- Rear right door window5- Lock switchDriver’s switchLHD
Driver’s switchRHD
BK0203201EN.book 29 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Electric window control4-30 Locking and unlocking
4
The driver’s switches can be used to operateall door windows. A window can be openedor closed by operating the correspondingswitch.Press the switch down to open the window,and pull up the switch to close it.If the switch for the driver’s window is fullypressed down/pulled up, the door windowautomatically opens/closes completely.If you want to stop the window movement,operate the switch lightly in the reverse direc-tion.
The passenger’s switches can be used to oper-ate the corresponding passenger’s door win-dows.Press the switch down for opening the win-dow, and pull up the switch for closing.
E00303101263
When this switch is operated, the passenger’sswitches cannot be used to open or close the
door windows and the driver’s switch cannotopen or close any door windows other thanthe driver’s door window.To u n l o c k , p r e s s i t o n c e a g a i n .
E00302401012
The door windows can be opened or closedfor 30 seconds after the engine is stopped.
WA R N I N GzBefore operating the electric window con-trol, make sure that nothing is capable ofbeing trapped (head, hand, finger, etc.).zNever leave the vehicle without removingthe key.zNever leave a child (or other person whomight not be capable of safe operation ofthe electric window control) in the vehiclealone.
Driver’s switches
Passenger’s switches
NOTE
zRepeated operation with the engine stoppedwill run down the battery. Operate the win-dow switches only while
the engine is run-
ning.zThe rear door windows only open halfway.
Lock switch
1- Lock2- UnlockWA R N I N GzA child may tamper with the switch at therisk of its hands or head being trapped inthe window. When driving with a child inthe vehicle, please press the window lockswitch to disable the passenger’s switches.
Timer function
BK0203201EN.book 30 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display6-4 Instruments and controls
6
[When the operation mode of the power switch is ON]
E00520001764
Each time the multi information displayswitch is operated, the buzzer sounds and themulti information display changes betweeninformation such as warnings, tripmeter,
1- NORMAL indicator display screen
Displayed when the ECO mode switchand 4WD lock switch are OFF.
2- ECO mode indicator display screen
Displayed when the ECO mode switch isON and the 4WD lock switch is OFF.
3- ECO LOCK indicator display screen
Displayed when the ECO mode switchand 4WD lock switch are ON.
4- 4WD LOCK indicator display screen
Displayed when the ECO mode switch isOFF and the 4WD lock switch is ON.m ECO mode switch P. 6-46m 4WD lock switch P. 7-19
5- Battery charge mode display screen
m P. 7-23
6- Battery save mode display screen
m P. 7-22
7-
mark display screen
m P. 6-9
8- Forward Collision Mitigation System
(FCM) OFF display screen
* m P. 7-55
9- Lane Departure Warning (LDW) display
screen
* m P. 7-60
10- Cruise control display screen
* m P. 7-35
11- Adaptive Cruise Control System (ACC)
display screen
* m P. 7-43
12- Speed limiter display screen
* m P. 7-39
13- Drive battery level display screen
m P. 6-9
14- Odometer
m P. 6-10
15- Information screen
m P. 6-7
16- Select position indicator
m P. 7-15
17- Fuel remaining display screen
m P. 6-9
18- Outside temperature display screen
m P. 6-10
Multi information display switch
BK0203201EN.book 4 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamp, warning lamp, and information screen display list
Instruments and controls 6-21
6
E00523701182E00523802034
Indicator lamp, warning lamp, and information screen display list Indicator and warning lamp list 1- Position lamp indicator lamp
m P. 6-37
2- Front fog lamp indicator lamp
m P. 6-37
3- Turn-signal indicator lamps/Hazard
warning indicator lamps
m P. 6-36
4- Rear fog lamp indicator lamp
*
m P. 6-37
5- High-beam indicator lamp
m P. 6-37
6- Plug-in Hybrid EV System warning
lamp
m P. 6-39
7- Auxiliary battery charge warning lamp
m P. 6-39
8- Charging indicator
m P. 6-37
9- Regenerative brake warning lamp
m P. 6-39
10- Ready indicator
m P. 6-37
11- Acoustic Vehicle Alerting System
(AVAS) OFF indicator lamp
m P. 7-24
12- Active Stability Control (ASC) indica-
tor lamp
m P. 7-34
13- Active Stability Control (ASC) OFF
indicator lamp
m P. 7-34
14- Anti-lock brake system (ABS) warning
lamp
m P. 7-30
15- Supplemental restraint system (SRS)
warning lampm P. 5-30
16- Check engine warning lamp
m P. 6-38
17- Seat belt warning lamp
m P. 5-11
18- Brake warning lamp
m P. 6-37
BK0203201EN.book 21 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamp, warning lamp, and information screen display list
Instruments and controls 6-23
6
zOne or more failure is occurring in the Plug-in Hybrid EV System.
zImmediately park the vehicle in a safe place and contact a MITSUBISHI MOTORS Authorised Service Point.
zThe parking lock unit is in failure. The Plug-in Hybrid EV system cannot be kept in standstill condition without applying the parking brake.
zPark the vehicle at a safe, flat place and apply the parking brake. Contact a MIT-SUBISHI MOTORS Authorised Service Point.Refer to “Electrical parking switch” on page 7-16.
zYo u a r e a t t e m p t i n g t o s e t t h e o p e r a t i o n mode to “ON” when the charge connector is connected to the charge port.
zDisconnect the charge connector from the charge port before operating the power switch.
zCharging was interrupted due to system failure (electric leak detected).
zThere is an electric leak or the normal charge cable is faulty. Immediately stop using the cable and contact a MITSUBI-SHI MOTORS Authorised Service Point.
zCharging was interrupted due to poor con-nection of the charge cable or power fail-ure.
zConnect the charge cable correctly.Refer to “Normal charging” on page 3-8.zIf charging is interrupted due to a power failure, charging will be automatically resumed when the power is restored.
Screen
Cause
Solution (Reference)
BK0203201EN.book 23 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamp, warning lamp, and information screen display list
Instruments and controls 6-27
6
zAn attempt was made to open the driver’s door with the operation mode in any mode other than OFF.
zPut the operation mode in OFF.Refer to “Operation mode ON reminder system” on page 7-12.
zAn attempt was made to lock all the doors and the tailgate with the operation mode is put in a mode other than OFF.
zPut the operation mode in OFF.Refer to “Operation mode OFF reminder system” on page 7-11.
zThere is a fault in the electrical system.
zImmediately stop the vehicle in a safe place.We r e c o m m e n d y o u t o c o n s u l t a MITSUBISHI MOTORS Authorised Ser-vice Point.
zThe engine is overheated.
zStop the vehicle in a safe place and take corrective measures.Refer to “Engine overheating” on page 9-4.
zYo u p u t t h e o p e r a t i o n m o d e i n O N w i t h o u t fastening your seat belt.
zFasten your seat belt properly. Refer to “Seat belt reminder” on page 5-11.
zThere is a fault in the fuel system.
zWe r e c o m m e n d y o u t o c o n s u l t a MITSUBISHI MOTORS Authorised Ser-vice point.
Screen
Cause
Solution (Reference)
BK0203201EN.book 27 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamp, warning lamp, and information screen display list6-34 Instruments and controls
6
Screen
System operation status
Reference
zWhen charging of the drive battery is com-pleted.
Refer to “Charging” on page 3-2.
zWhen the mode is changed by the opera-tion of the 4WD lock switch or ECO mode switch.
Refer to “ECO mode switch” on page 6-46.Refer to “4WD lock switch” on page 7-19.Refer to “When the ECO mode switch is ON” on page 7-20.
zWhen approaching the guidance location, etc.
Refer to “Navigation information display” on page 6-32.
BK0203201EN.book 34 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Combination headlamps and dipper switch
Instruments and controls 6-43
6
E00528901600
This function turns on the position and taillamps for about 30 seconds after theUNLOCK switch on the remote control trans-mitter is pressed when the combination head-lamps and dipper switch is in the “OFF” or“AUTO” position (for vehicles equipped withthe automatic lamp control). On vehiclesequipped with the automatic lamp control(except for vehicles equipped with LDW), thewelcome light function will operate onlywhen it is dark outside the vehicle.
E00529001549
This function turns on the headlamps in thelow beam setting for about 30 seconds afterthe operation mode is put in OFF.1. Turn the combination headlamps and dip-per switch to the “OFF” or “AUTO” posi-tion (for vehicles equipped with theautomatic lamp control).2. Put the operation mode of the powerswitch in OFF.
3. Within 60 seconds of putting the opera-tion mode in OFF, pull the turn signallever towards you.4. The headlamps will come on in the lowbeam setting for about 30 seconds. Afterthe headlamps go off, the headlamps canbe turned on again in the low beam settingfor about 30 seconds by pulling the turnsignal lever towards you within 60 sec-onds of putting the operation mode inOFF.To t u r n o n t h e h e a d l a m p s a g a i n a f t e r 6 0seconds of putting the operation mode inOFF, repeat the process from step 1.
NOTE
zThe high beams can also flash when the lampswitch is OFF.zIf you turn the lamps off with the headlampsset to highbeam, the headlamps are automati-cally returned to their low-beam settingwhen the lamp switch is next turned to the“” position.
We l c o m e l i g h t
NOTE
zWhile the welcome light function is operat-ing, perform one of the following operationsto cancel the function.•Push the LOCK switch on the remote con-trol transmitter.
•Turn the combination headlamps and dip-per switch to the “ ” or “ ” position.•Put the operation mode of the power switchin ON.
zIt is possible to modify
functions as follows:
•The headlamps can be set to come on in thelow beam setting.•The welcome light function can be deacti-vated.For further information, please contact yourMITSUBISHI MOTORS Authorised ServicePoint.On vehicles equipped
with Mitsubishi Multi-
Communication System (MMCS), screenoperations can be used to make the adjust-ment. Refer to the separate owner’s manualfor details.
Coming home light
NOTE
NOTE
zWhile the coming home light function isoperating, perform one of the followingoperations to cancel the function.•Pull the turn signal lever towards you.
BK0203201EN.book 43 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分