2014 MITSUBISHI OUTLANDER SPORT radio

Installation of accessories2-14 General information
2
2. The fuel tank filler is located on the rearleft side of your vehicle.Open the fuel tank filler door with therelease lever located the side of thedriver’s seat.3. Open the fuel tank filler tube by slowlyturning the cap anticlockwise.
4. Insert the gun in the tank port as far as itgoes.
5. When the gun stops automatically, do notfill with fuel any more.6. To close, turn the fuel cap slowly clock-wise until you hear clicking sounds, thengently push the fuel tank filler doorclosed.
E00200300963
We r e c o m m e n d y o u t o c o n s u l t y o u rMITSUBISHI MOTORSAuthorised Service Point.zThe installation of accessories, optionalcomponents, etc., should only be carriedout within the limits prescribed by law inyour country, and in accordance with theguidelines and warnings contained withinthe documents accompanying this vehicle.zInstalling electric components incorrectlycould lead to a fire. See the “Modifica-tion/alterations to the electrical or fuelsystems” section within this owner’s man-ual.zUsing a cellular phone or radio set insidethe vehicle without an external antennamay cause electrical system interference,which could lead to unsafe vehicle opera-tion.
1- Remove2- Close
CAUTIONzSince the fuel system
may be under pressure,
remove the fuel tank filler tube cap slowly.This relieves any pressure or vacuum thatmight have built up in the fuel tank. If youhear a hissing sound, wait until it stopsbefore removing the cap. Otherwise, fuelmay spray out, injuring you or others.NOTE
zWhile filling with fuel, hang the fuel cap onthe hook (A) located on the inside of the fueltank filler door.CAUTIONzDo not tilt the gun.
Installation of accessories
BK0203201EN.book 14 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

MITSUBISHI Remote Control*3-18 Charging
3
zCustomize (function setting change)The function setting of the keyless opera-tion system, security alarm, outside rear-view mirror, operation mode of the powerswitch, air conditioning, lamps and wind-screen wipers can be changed by MIT-SUBISHI Remote Control.
Devices that support wireless LAN arerequired to communicate with the vehicleusing the MITSUBISHI Remote Control.Also, an SSID* (A) and password (B) arerequired to connect a wireless LAN device tothe vehicle. The SSID and password comewith the key at the time of your purchase ofthe vehicle.
NOTE
zThe electric heater is required to activate thereservation functions of
heater, defroster and
demister.zDue to the communication distance differsdepending on the wireless LAN device, thecommunication may down.
*: An SSID is the identifier of an access
point for IEEE 802.11 series wirelessLAN. It is displayed on wireless LANdevices.
For the operation method of the MITSUBI-SHI Remote Control, please visit Mitsubishi Motors’ Web site:http://www.mitsubishi-motors.com/en/prod-ucts/outlander_phev/app/remote/index.htmlzIf you need further information, please contact a MITSUBISHI MOTORS Authorized Service Point.
WA R N I N GzDo not use the MITSUBISHI RemoteControl if children, persons in need ofcare, pets, etc. are in the vehicle. Even ifthe remote climate control is used, thecabin may become hot or cold due to somereasons such as automatic stop of the sys-tem. The cabin temperature may quicklyrise in sunshine, which poses a risk of heatstroke and dehydration. In cold weather,on the other hand, the cabin temperaturemay quickly drop. Either of which couldlead to death in the worst case.zThe cooling fan in
the engine compart-
ment may operate automatically whencharging or when operating air condi-tioner. Do not bring you
r hand close to the
cooling fan during charging.CAUTIONzDo not use the timer charging or the remoteclimate control with a car cover.NOTE
zKeep the following points in mind whenusing a wireless LAN device:•Communication speed and range varydepending on the wirele
ss LAN devices and
the surrounding conditi
ons (radio environ-
ment, obstacles, parking area environment,etc.).
BK0203201EN.book 18 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

MITSUBISHI Remote Control*
Charging 3-19
3
•Due to the characteristics of radio waves,communication speed tends to decrease asthe communication distance increases. Useyour wireless LAN devi
ce at a short dis-
tance from the vehicle for better response.•When a microwave oven or ISM (indus-trial, scientific and medical) equipment isbeing used, the communication speed andrange of wireless
LAN devices may
decrease. Use your wireless LAN deviceaway from these appliances and equipment.•If a wireless LAN de
vice and Bluetooth
(registered trademark of Bluetooth SIG,Inc.) are used simultaneously, the commu-nication speed and range of each devicemay decrease. Use your wireless LANdevice away from Bluetooth devices.
zWireless LAN de
vices may not communicate
with the vehicle, or may not operate nor-mally or stably in the following environmentor situations. Check th
at the device can com-
municate with your vehicle before use.•There is an obstructi
on such as a concrete
or metal wall between the vehicle and wire-less LAN device.•The vehicle is surrounded by tall vehiclesin a parking lot.•There are facilities nearby that emit strongradio waves, such as a TV tower, trans-former substation, br
oadcasting station or
airport.NOTE
•There is a communication device such as amobile phone or radio, or an electric devicesuch as a personal computer near the wire-less LAN device.•The wireless
LAN device is in contact with
or covered by a metal object.•The battery of the wireless LAN device hasrun down.
zThe MITSUBISHI Remote Control cannotbe used under the following conditions:•The wireless LAN device is turned off.•The MITSUBISHI Re
mote Control appli-
cation software is not installed.•The MITSUBISHI Re
mote Control appli-
cation software is not running.•The wireless LAN devi
ce is not registered
on the vehicle or it is not connected to thevehicle.•The wireless LAN devi
ce is out of the com-
munication range.•The wireless
LAN device is
connected to
other wirele
ss LAN device.
•The wireless LAN devi
ce has failed, or its
battery has run out.
zSome charging facilities have a timer func-tion that turns the power on or off at a spe-cific time of the day. When charging at afacility with a timer function, make sure thatthe charging timer is set within the timeperiod when the power in the charging facil-ity is on.NOTE
zThe auxiliary battery is automatically andperiodically charged using electrical powerstored in the drive battery.zWhile the remote climate control is operatingor the charging, the cooling fan or air condi-tioner compressor may start operating and itssound may be heard.
This is normal.
zThe remote climate control operates in itsown mode based on the mode selected on thewireless LAN device,
regardless of the
switch setting of the vehicle’s air condi-tioner.zAir conditioning perform
ance may deterio-
rate or the remaining quantity of the drivebattery may decrease under the followingconditions:•In extremely hot weather.•In hot sunshine.•In extremely cold weather.zIf the remote climate control is started duringcharging, the time until full charge mayextend or the charging rate may decrease.zWhen the remaining quantity of the drivebattery is decreased, the remote climate con-trol does not operate
or it may stop on the
way.NOTE
BK0203201EN.book 19 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Keyless entry system
Locking and unlocking 4-5
4
E00310301296
The door and tailgate unlock function can beset to the following two conditions.Each time the door and tailgate unlock func-tion is set, a chime will sound to tell you thecondition of the door and tailgate unlockfunction.1. Put the operation mode in OFF.2. Place the combination headlamps and dip-per switch in the “OFF” position, andleave the driver’s door open.3. Press the LOCK switch (1) for 4 to 10seconds and press the UNLOCK switch(2) during this time.
4. Release in sequence the LOCK andUNLOCK switches within 10 seconds ofpressing the LOCK switch in step 3.
E00309501243
Before replacing the battery, remove staticelectricity from your body by touching ametal grounded object.
zThe keyless entry system does not operatewhen the door or tailgate is open.zThe remote control switch will operatewithin about 4 m from the vehicle. However,the operating range of the remote controlswitch may change if the vehicle is locatednear a power station,
or radio/TV broadcast-
ing station.zIf either of the following problems occurs,the battery may be exhausted.•The remote control switch is operated at thecorrect distance from the vehicle, but thedoors and tailgate are
not locked/unlocked
in response.•The indicator lamp (4) is dim or does notcome on.For further information, please consult yourMITSUBISHI MOTORS Authorised Ser-vice Point.If you replace the battery yourself, refer to“Procedure for replacing the remote controlswitch battery” on page 4-5.
zIf your remote control switch is lost or dam-aged, please contact
your MITSUBISHI
MOTORS Authorised Service Point for areplacement remote control switch.zIf you wish to add a remote control switch,we recommend you to contact yourMITSUBISHI MOTORS Authorised ServicePoint.The below remote control switches are avail-able for your vehicle.NOTE
•Keyless operation key: up to 4 remote con-trol switches
Setting of door and tailgate unlock function Number of chimes
Condition
One chime
All doors and the tailgate unlock
Tw o chimes
Driver’s door unlock only
NOTE
NOTE
zOn vehicles equipped
with Mitsubishi Multi-
Communication System (MMCS), screenoperations can be used to make the adjust-ment. Refer to the se
parate owner’s manual
for details.
Procedure for replacing the remote control switch battery
BK0203201EN.book 5 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Keyless operation system4-6 Locking and unlocking
4
1. With the MITSUBISHI mark facing you,insert the cloth-covered tip of a straightblade (or minus) screwdriver into thenotch in the case and use it to open thecase.2. Remove the old battery.
3. Install a new battery with the + side (A)up.4. Close the case firmly.5. Check the keyless operation function tosee that it works.
E00305601608
The keyless operation system allows you tolock and unlock the doors and tailgate andstart the engine simply by carrying the key-less operation key with you.The keyless operation key can also be used asthe keyless entry system remote controlswitch.Refer to “Keyless entry system” on page 4-3.The driver should always carry the keylessoperation key. This key is necessary for lock-ing and unlocking the doors and tailgate,starting the engine and otherwise operatingthe vehicle, so before locking and leaving thevehicle, be sure to check that you have thekeyless operation key.
NOTE
zBe sure to perform the procedure with theMITSUBISHI mark facing you. If theMITSUBISHI mark is not facing you whenyou open the case, the transmitter may comeout.
NOTE
zYo u m a y p u r c h a s e a r e p l a c e m e n t b a t t e r y a tan electric appliance store.zA MITSUBISHI MOTORS Authorised Ser-vice Point can replace the battery for you ifyou prefer.CAUTIONzWhen the remote control switch case isopened, be careful to keep water, dust, etc.out. Also, do not touch
the internal compo-
nents.
+ side- side
Coin type battery CR2032
Keyless operation system
WA R N I N GzPeople with implantable cardiac pacemak-ers or implantable
cardiovascular-defi-
brillators should no
t go near the exterior
transmitters (A) or the interior transmit-ters (B). The radio waves used by the key-less operation system could adverselyaffect implantable cardiac pacemakers orimplantable cardiovascu
lar-defibrillators.
BK0203201EN.book 6 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Keyless operation system
Locking and unlocking 4-7
4
Yo u c a n l i m i t t h e p o s s i b l e o p e r a t i o n s o fthe keyless operation system in the fol-lowing ways. (The keyless operation sys-tem can be used as a keyless entrysystem.) Please consult a MITSUBISHIMOTORS Authorised Service Point.
•You can limit operations to locking andunlocking the doors and tailgate.•You can limit operations to starting theengine.• The keyless operation system can be dis-abled.When keyless operation system opera-tions are modified, the transmitters oper-ate as follows.•Only locking and unlocking doors ortailgate: exterior transmitter and interiortransmitter•Only starting the engine: interior trans-mitter
E00305700556
If you are carrying the keyless operation key,enter the operating range of the keyless oper-
WA R N I N GzWhen using electromedical devices otherthan implantable cardiac pacemakers orimplantable cardiovascular-defibrilla-tors, contact the electromedical devicemanufacturer ahead of time to determinethe affects of radio waves on the devices.Electromedical device operations could beaffected by radio waves.
NOTE
zThe keyless operation ke
y uses an ultra-weak
electromagnetic wave. In the followingcases, the keyless ope
ration system may not
operate properly or
may be unstable.
•When there is equipment nearby that emitsstrong radio waves, such as: a power sta-tion, a radio/TV broa
dcasting station or an
airport.•The keyless operation system is carriedtogether with a communications devicesuch as a cellular phone
or radio set, or with
an electronic device such as a personalcomputer.•The keyless operati
on key is touching or
covered by a metal object.
•A keyless entry system is being usednearby.•When the keyless operation key battery isworn out.•When the keyless operation key is set downin an area with strong radio waves or noise.In such cases, use the emergency key.Refer to “To operate
without using the key-
less operation functi
on” on page 4-13.
zBecause the keyless operation key receivessignals in order to communicate with thetransmitters in the vehicle, the battery con-tinually wears down regardless of keylessoperation key use. The battery life is 1 to 3years, depending on usage conditions. Whenthe battery wears out, replace the batteryaccording to the description in this manual orhave it replaced at your MITSUBISHIMOTORS Authorised Service Point.Refer to “Procedure for replacing the remotecontrol switch battery” on page 4-5.zBecause the keyless
operation key continu-
ally receives signals, strong radio wavereception could affect battery wear. Do notleave the key near a TV, personal computer,or other electronic device.
Operating range of the keyless operation system
NOTE
BK0203201EN.book 7 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamp, warning lamp, and information screen display list6-22 Instruments and controls
6
E00523901344
When there is information to be announced, such as lamp reminder, the buzzer sounds and the screen switches to the displays sho
wn below. Refer
to the appropriate page and take the necessary measures.When the cause of the warning display is eliminated, the warning display goes out automatically.Refer to “Warning display list” on page 6-22.Refer to “Navigation information display” on page 6-32.Refer to “Other interrupt displays” on page 6-33.
E00524001993
19- Information screen display list
m P. 6-22
Information screen display list
NOTE
zA warning may be displayed on the in
formation screen and the buzzer ma
y sound in the following rare cases.
This is caused by the system picking up inte
rference such as noise or strong electromagnetic waves, and is not a functional pro
blem.
•An extremely strong electromagnetic wave is received from a source such as an illegal radio set, a spark from a wire, or a rad
ar station.
•Abnormal voltage or a static electricity
discharge is generated by th
e operation of installed elect
rical equipment (including
after-market parts).
If the warning display appears many times,
we recommend you to consult a MITSUBISHI MOTORS Authorised Service Point.
Warning display li st
Screen
Cause
Solution (Reference)
zOne or more minor failure is occurring in the Plug-in Hybrid EV System.
zHave your vehicle inspected by a MIT-SUBISHI MOTORS Authorised Service Point.
BK0203201EN.book 22 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Reversing sensor system*7-64 Starting and driving
7
Depending on whether the vehicle isequipped with a towbar, you can change thereversing sensor system between the standardmode and the towbar mode. The towbar modechanges the system to exclude the area inwhich the towbar is mounted from the detec-tion areas.The detection areas are within approximately60 cm (A) from the corner sensors, 150 cm(B) from the back sensors, and 60 cm (C) orless from the ground surface, excluding thearea approximately 10 cm (D) from theground surface.
The detection areas are within approximately60 cm (A) from the corner sensors, 150 cm(B) from the back sensors, and 60 cm (C) orless from the ground surface, excluding thearea approximately 10 cm (D) from theground surface. The non-detection areas (E)are within approximately 20 cm (F) from thebumper.
For information on how to change the detec-tion areas, please refer to “Changing thedetection areas” on page 7-66.
Reversing sensor system detection areas

Ve h i c l e s w i t h o u t a t o w b a r
Ve h i c l e s w i t h a t o w b a r
NOTE
zIf the rear bumper has been exposed to animpact, the corner or back sensors may failand prevent the system from functioningproperly. Have the vehicle inspected at aMITSUBISHI MOTORS Authorised ServicePoint.zThe sensors do not detect objects located inthe area directly below or near the bumper. Ifthe height of an object is lower than themounted position of the corner or back sen-sors, the sensors may not continue detectingit even if they detected it initially.CAUTIONzThe reversing sensor
system may not operate
properly under the following conditions:•The sensors or surroundings are coveredwith ice, snow, or mud.•The sensors are frozen.•The system receives ultrasonic noise fromother sources (the horns
of other vehicles,
motorcycle engines, brakes, radios, pouringrain, splashing water,
snow traction device
(tyre chains), etc.).•The sensors are extremely hot or cold(while the vehicle is parked for a longperiod of time under a blazing sun or incold weather).
BK0203201EN.book 64 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分