2014 MITSUBISHI OUTLANDER SPORT open bonnet

Inside tailgate release4-24 Locking and unlocking
4
E00303400298
The inside tailgate release is designed to pro-vide a way to open the tailgate in the case of adischarged battery.The tailgate release (see illustration) ismounted on the tailgate.Yo u a n d y o u r f a m i l y s h o u l d f a m i l i a r i s e y o u r -selves with the location and operation of thetailgate release.
1. Open the lid (A) inside of the tailgate.2. Move the lever (B) to open the tailgate.3. Push out on the tailgate to open it.
E00301501973
The security alarm system is for alerting thesurrounding area of suspicious behaviour toprevent unlawful entry into the vehicle byoperating an alarm if a door, the tailgate orthe bonnet is opened when the vehicle has notbeen unlocked using the keyless entry systemor the keyless operation function.
Inside tailgate release
To o p e n Ta i l g a t e
Electric tailgate
CAUTIONzAlways keep the release lever lid on tailgateclosed when driving so that your luggagecannot accidentally bump the lever and openthe tailgate.
Security alarm system
*
CAUTIONzDo not modify or add parts to the securityalarm system.Doing so could cause the security alarm tomalfunction.NOTE
zThe alarm system will not be activated if thedoors and the tailgate have been locked usinga key, the central door
lock switch (instead of
the keyless entry system or the keyless oper-ation function).
BK0203201EN.book 24 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Security alarm system*4-26 Locking and unlocking
4
If an unlawful opening of any of the doors,tailgate or bonnet is detected during the sys-tem armed mode, the alarm will be activatedto warn people around the vehicle of anabnormal condition.Inside alarm (approx. 10 seconds):
The buzzer sounds, warning those insidethe vehicle of an abnormal condition.(except for vehicles equipped with theinterior alarm sensor)
Outside alarm (approx. 30 seconds):
The turn-signal lamps blink and the horn(the siren for vehicles equipped with theinterior alarm sensor) sounds, warningpeople around the vehicle of an abnormalcondition.
Refer to “Alarm activation” on page 4-28.
It is possible to cancel the system activationduring the system preparation mode or thesystem armed mode.In addition, it is possible to cancel the alarmonce it has been activated.Refer to “Cancelling the system” on page4-28, “Cancelling the alarm” on page 4-29.
E00301701988
Follow the procedure be
low to set the system
to the system armed mode.1. Put the operation mode in OFF.2. Exit the vehicle and close all of the doors,tailgate and bonnet.
3. Press the LOCK switch (A) on the remotecontrol switch of the keyless operationkey, the driver’s or front passenger’s doorlock/unlock switch (B), or the tailgateLOCK switch (C) in order to lock all thedoors and the tailgate.
Alarm activation

NOTE
zThe alarm will resume if unlawful actionsare taken again, even if the alarm hasstopped.
System cancellation

NOTE
zWhen lending the vehicle to another personor allowing the vehicle to be driven by some-one who is unfamiliar with the security alarmsystem, be sure to give the person a properexplanation of the se
curity alarm system.
If a person who is unfamiliar with the secu-rity alarm system accidentally unlocked thevehicle, causing the alarm to sound, thealarm would be a nuisance to people nearby.
Setting the system

Driver’s and front passenger’s door lock/unlock switches
*
BK0203201EN.book 26 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Security alarm system*
Locking and unlocking 4-27
4
By locking the vehicle using the keylessentry system or the keyless operationfunction, the system preparation mode isactivated.The buzzer makes an intermittent beepingsound and the security indicator (D) in thecentre panel flashes for confirmation.
4. After approximately 20 seconds, thebuzzer stops, and when the blinking of thesecurity indicator starts to slow down, thesystem armed mode goes into effect.The security indicator continues to blinkduring the system armed mode.
E00312101416
The vehicle inclination detection function andthe interior intrusion detection function canbe deactivated when parking in automated carparks or leaving pets in the vehicle or leavingthe vehicle with the windows slightly open.1. Put the operation mode in OFF.2. Raise and hold the wiper and washerswitch to the “MIST” position for about 3seconds. The buzzer will sound once andthe function will be deactivated.
To a c t i v a t e t h e f u n c t i o n a g a i n , r a i s e a n d h o l dthe wiper and washer switch to the “MIST”position for about 3 seconds.The buzzer will sound twice and the functionwill be activated.
Ta i l g a t e L O C K s w i t c h
*
NOTE
zThe system preparation mode is not activatedwhen the doors and the tailgate have beenlocked using a method ot
her than the keyless
entry system or the keyless operation func-tion (namely a key, the inside lock knob orthe central door lock switch).zIf the bonnet is open, the security indicatorilluminates, and the system does not enterthe system preparation mode.When the bonnet is closed, the system entersthe system preparation mode, and after about20 seconds the system enters the systemarmed mode.NOTE
zThe security alarm system can be activatedwhen people are riding inside the vehicle orwhen the windows are open. To prevent acci-dental activation of the alarm, do not set thesystem to the system armed mode while peo-ple are riding in the vehicle.zAv o i d l e a v i n g v a l u a b l e i t e m s i n s i d e t h e v e h i -cle even when the secu
rity alarm system has
been set to the “active” mode.
To d e a c t i v a t e t h e v e h i c l e i n c l i n a -tion detection function and the interior intrusion detection func-tion

BK0203201EN.book 27 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Security alarm system*4-28 Locking and unlocking
4
E00301801859
The following methods can be used to cancelthe system when it is in the system prepara-tion mode or the system armed mode.zPressing the UNLOCK switch on theremote control switch.zPutting the operation mode in ON.zOpening any one of the doors or the tail-gate, when the system is in the systempreparation mode.
zHolding the keyless operation key andpressing the driver’s or front passenger’sdoor lock/unlock switch, or the tailgateopen switch to unlock the doors and thetailgate.
E00301902118
When the system is in the system armedmode, the alarm will be activated as followsif the vehicle is unlocked or if any of thedoors, tailgate or bonnet is opened using amethod other than the keyless entry system orthe keyless operation function.
NOTE
The function will be activated again if the fol-lowing operation is performed.zIf the doors and the tailgate are unlockedusing the keyless entry
system or the keyless
operation function.zIf the operation mode is put in on or ACC.
Cancelling the system

NOTE
zIf the bonnet is opened during the systempreparation mode, the system preparationmode is suspended.The system returns to the system preparationmode when the bonnet is closed.zIf the battery terminals are disconnectedwhile the system is in
the system preparation
mode, the memory will be erased.zIt is possible to regist
er up to 4 remote con-
trol switches.As long as they are registered, any of theremote control switches, other than the oneused to activate the system, can be used tocancel the system.If you want to register additional remotecontrol switches, please contact aMITSUBISHI MOTORS Authorised ServicePoint.zThe activation distance for keyless entry sys-tem is approximately 4 m.If it is not possible to lock or unlock thevehicle by pressing the switch at the correctdistance or the security alarm system cannotbe set or cancelled using the switch, the bat-tery may need to be replaced.Replace the battery at a MITSUBISHIMOTORS Authorised Service Point.
zIf the UNLOCK switch on the remote con-trol switch, or the driver’s or front passen-ger’s door lock/unlock switch is pressed andno door or the tailgate is opened within 30seconds, the doors and the tailgate will auto-matically relock. In this
case as well, the sys-
tem preparation mode will go into effect.zThe time between pressing of the UNLOCKswitch on the remote control switch, or thedriver’s or front passenger’s doorlock/unlock switch and automatic lockingcan be adjusted. Please consult aMITSUBISHI MOTORS Authorised ServicePoint.On vehicles equipped with Mitsubishi Multi-Communication System (MMCS), screenoperations can be used to make the adjust-ment. Refer to the separate owner’s manualfor details.
Alarm activation

NOTE
BK0203201EN.book 28 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Electric window control
Locking and unlocking 4-29
4
1. The inside alarm will be activated forapproximately 10 seconds. (except forvehicles equipped with the interior alarmsensor)2. The alarm will be activated for approxi-mately 30 seconds.The turn-signal lamps will flash, and thehorn (the siren for vehicles equipped withthe interior alarm sensor) will sound inter-mittently.3. The alarm will resume if unlawful actionsare taken again, even if the alarm hasstopped.
E00302001698
It is possible to halt the activation of an alarmusing the following methods:zPressing the LOCK or UNLOCK switchon the remote control switch.(After pressing of the LOCK switch, thevehicle will lock if all the doors and thetailgate are closed, after which the systempreparation mode will once again go intoeffect.)zPutting the operation mode in ON.zHolding the keyless operation key andlocking or unlocking the doors and thetailgate using the keyless operation func-tion.
E00302201632
The electric windows can only be operatedwith the operation mode in ON.
E00302301822
Each door window opens or closes while thecorresponding switch is operated.
NOTE
zIf the bonnet is opened during the systemarmed mode, the vehicl
e outside alarm oper-
ates immediately.
Cancelling the alarm

NOTE
zWhen the ignition switch is turned to the“ON” position or the operation mode is putin ON, the buzzer sounds 4 times. This oper-ation indicates that the alarm was activatedwhile the vehicle was parked.Please check the inside of the vehicle to con-firm that nothi
ng was stolen.
zEven if the battery is disconnected, the alarmactivation memory will not be erased.
Electric window control Electric window control switch 1- Driver’s door window2- Front passenger’s door window3- Rear left door window4- Rear right door window5- Lock switchDriver’s switchLHD
Driver’s switchRHD
BK0203201EN.book 29 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamp, warning lamp, and information screen display list6-26 Instruments and controls
6
zThe RBS (regenerative brake system) can-not be used.
zWe recommend you to consult a MITSUB-ISHI MOTORS Authorised Service Point.
zThere is a fault in the ABS.
zAv o i d s u d d e n b r a k i n g a n d h i g h - s p e e d d r i v -ing, stop the vehicle in a safe place, and take corrective measures. Refer to “ABS warning” on page 7-30.
zOne of the doors or the tailgate is not com-pletely closed.The open door is displayed.
zClose the door or tailgate.Refer to “Door ajar warning display screen” on page 6-9.
zThe bonnet is open.
zClose the bonnet.Refer to “Bonnet” on page 11-3.
zThere is a fault in the electronic immobi-lizer (Anti-theft starting system).
zPut the operation mode in OFF, and then start the Plug-in Hybrid EV System again.If the warning is not cancelled, please con-tact a MITSUBISHI MOTORS Authorised Service Point.
Screen
Cause
Solution (Reference)
BK0203201EN.book 26 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Emergency starting
For emergencies 9-3
9
2. Turn off all lamps, heater and other elec-trical loads.3. Set the parking brake firmly on each vehi-cle. Set the gear of another vehicle in “P”(PARK) position (with A/T) or in “N”(Neutral) position (with M/T) and stop theengine.4. Open the bonnet, remove the fuse coverof the main fuse block.Refer to “Bonnet” on page 11-3 and“Fuses: Engine compartment” on page11-16.
5. Open the cover of the jumper cable termi-nal in the main fuse block.
6. Connect one end of one jumper cable to the jumper cable terminal (A) of yourvehicle, and the other end to the posi-tive (+) terminal of the booster battery(B).Connect one end of the other jumper cable to the negative (-) terminal of thebooster battery, and the other end tothe designated ground location of yourvehicle.
WA R N I N GzWhen connecting the jumper cable, stopthe engine in another vehicle. Otherwise,the cables or your cl
othes may be caught
by the fan or drive belt and personalinjury could result.zThe cooling fan turns on and off depend-ing on the coolant temperature. Do notbring your hands close to the fan while theengine is running or Plug-in Hybrid EVSystem is operating.
NOTE
zYo u c a n n o t r e s c u e o t h e
r vehicle’s discharged
battery by connecting jumper cables usingthis jumper cable terminal.
BK0203201EN.book 3 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Engine overheating9-4 For emergencies
9
7. Start the engine in the vehicle which hasthe booster battery, let the engine idle afew minutes, then start the Plug-in HybridEV system in your vehicle.8. Check that the ready indicator illuminates.If the ready indicator does not illuminate,contact a MITSUBISHI MOTORSAuthorised Service Point.9. When the ready indicator illuminates, dis-connect the jumper cables in the reverseorder of connection.
10. Check that the select position can be
shifted to all positions other than the “P”(PARK) position.
11. Have the auxiliary battery inspected by
your nearest MITSUBISHI MOTORSAuthorised Service Point.
E00800603745
When the engine is overheating, the informa-tion screen in the multi information displaywill be interrupted and the engine coolanttemperature warning display will appear.If this occurs, take the following correctivemeasures:1. Stop the vehicle in a safe place.
2. Check whether steam is coming from theengine compartment.[If steam does not come from the enginecompartment]Wi t h t h e Pl ug - i n H yb r i d E V s ys t em s t i l lstarting, raise the bonnet to ventilate theengine compartment.[If steam is coming from the engine com-partment]Stop the Plug-in Hybrid EV system, andwhen the steam stops, raise the bonnet toventilate the engine compartment. Restartthe Plug-in Hybrid EV system.
WA R N I N GzWhen connecting the jumper cables, donot connect the positive (+) cable to thenegative (-) terminal. Otherwise sparksmight cause explosion of the battery.CAUTIONzUse care not to get the jumper cable caughtin the cooling fan or other rotating part in theengine compartment.NOTE
zIf the jumper cable is
connected to the any
position other than a
ppointed position, it
may could cause damage to the vehicle.
CAUTIONzYo u r v e h i c l e i s e q u i p p e d w i t h a n e x c l u s i v eauxiliary battery. Even if the battery type isthe same, the battery may not be correctlyinstalled in your vehicle. When replacing theauxiliary battery, request a MITSUBISHIMOTORS Authorised Service Point to do so.
Engine overheating
WA R N I N GzDo not open the bonnet while steam iscoming from the engine compartment. Itcould cause steam or hot water to spurtout, causing burns. Hot water could spurtout even when there is no steam comingout, and some parts will be very hot. Bevery careful when opening the bonnet.zBe careful of hot steam, which could beblowing off the reserve tank cap.zDo not attempt to remove the radiator capwhile the engine is hot.
BK0203201EN.book 4 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分