2014 MITSUBISHI OUTLANDER SPORT change time

Multi information display6-4 Instruments and controls
6
[When the operation mode of the power switch is ON]
E00520001764
Each time the multi information displayswitch is operated, the buzzer sounds and themulti information display changes betweeninformation such as warnings, tripmeter,
1- NORMAL indicator display screen
Displayed when the ECO mode switchand 4WD lock switch are OFF.
2- ECO mode indicator display screen
Displayed when the ECO mode switch isON and the 4WD lock switch is OFF.
3- ECO LOCK indicator display screen
Displayed when the ECO mode switchand 4WD lock switch are ON.
4- 4WD LOCK indicator display screen
Displayed when the ECO mode switch isOFF and the 4WD lock switch is ON.m ECO mode switch P. 6-46m 4WD lock switch P. 7-19
5- Battery charge mode display screen
m P. 7-23
6- Battery save mode display screen
m P. 7-22
7-
mark display screen
m P. 6-9
8- Forward Collision Mitigation System
(FCM) OFF display screen
* m P. 7-55
9- Lane Departure Warning (LDW) display
screen
* m P. 7-60
10- Cruise control display screen
* m P. 7-35
11- Adaptive Cruise Control System (ACC)
display screen
* m P. 7-43
12- Speed limiter display screen
* m P. 7-39
13- Drive battery level display screen
m P. 6-9
14- Odometer
m P. 6-10
15- Information screen
m P. 6-7
16- Select position indicator
m P. 7-15
17- Fuel remaining display screen
m P. 6-9
18- Outside temperature display screen
m P. 6-10
Multi information display switch
BK0203201EN.book 4 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display
Instruments and controls 6-5
6
average fuel consumption, EV cruising range,total cruising range,
EVHV driving rate,
energy flow, etc.It is also possible to change elements such asthe language and units used on the multiinformation display by operating the multiinformation display switch.
E00520201812
Each time you lightly press the multi info
rmation display switch, the display screen switches in the following order.
Information screen (when the operation mode is OFF) *1:When there is no warning display*2:When there is a warning display
*1*2
BK0203201EN.book 5 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display6-6 Instruments and controls
6
E00520701918
When the operation mode is put in ON, the display screen switches in the following order.1-
Tripmeter
m P. 6-10
2-
Tripmeter
m P. 6-10
3- ECO score display
m P. 6-14
4- Prediction charging time
m P. 3-8
5- Service reminder
m P. 6-11
6- Redisplay of a warning display screen
m P. 6-8
Information screen (when the operatio
n mode is changed from OFF to ON)
*:When the inspection time has arrived1- Screen when the operation mode is OFF2- System check screen
m P.6-12
3- Screen when the operation mode is ON4- Service reminder
m P.6-11
*
BK0203201EN.book 6 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display
Instruments and controls 6-11
6
To r e t u r n t h e d i s p l a y t o 0 , h o l d d o w n t h emulti information display switch for about 2seconds or more. Only the currently dis-played value will be reset.ExampleIf tripmeter is displayed, only tripmeter
will be reset.
E00522502021
Displays the approximate time until the nextperiodic inspection recommended by
MITSUBISHI MOTORS. “---” is displayedwhen the inspection time has arrived.
1. Displays the time until the next periodicinspection.2. This informs you that a periodic inspec-tion is due. We recommend you to consulta MITSUBISHI MOTORS AuthorisedService Point.At that time, when the operation mode ischanged from OFF to ON, the warningdisplay is displayed for a few seconds onthe information screen.3. After your vehicle is inspected at aMITSUBISHI MOTORS Authorised Ser-vice Point, it displays the time until thenext periodic inspection.
The “---” display can be reset while the oper-ation mode of the power switch is in OFF.
Example usage of tripmeter and tripmeter
It is possible to measure two currentlytravelled distances, from home using trip-meter and from a particular point onthe way using tripmeter .
To r e s e t t h e t r i p m e t e r
NOTE
zWhen disconnecting the auxiliary battery ter-minal, the memory of tripmeter and are cleared, and the display returns to “0”.
Service reminder
NOTE
zDepending on the vehicle specifications, thedisplayed time may differ from the next peri-odic inspection time recommended byMITSUBISHI MOTORS.In addition, the display settings for the nextperiodic inspection time can be modified.To modify the display settings, have itadjusted at a MITSUBISHI MOTORSAuthorised Service Point.For more details, consult a MITSUBISHIMOTORS Authorised Service Point.
NOTE
zThe distance is show
n in units of 100 km
(100 miles). The time is
shown in units of
months.
To r e s e t
BK0203201EN.book 11 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display6-12 Instruments and controls
6
When the display is reset, the time until thenext periodic inspection is displayed and thewarning display is no longer displayed whenthe operation mode is changed from OFF toON.1. When you lightly press the multi informa-tion display switch a few times, the infor-mation screen switches to the servicereminder display screen.2. Press and hold the multi information dis-play switch for about 2 seconds or more todisplay “ ” and make it flash. (If there isno operation for about 10 seconds withflashing, the display returns to the previ-ous screen.)
3. Lightly press the multi information dis-play switch while the icon is flashing tochange the display from “---” to“CLEAR”. After this, the time until thenext periodic inspection will be displayed.
E00531001038
When the operation mode is put in ON, thesystem check screen is displayed for about 4seconds. If there is no fault, informationscreen (when the operation mode is ON) isdisplayed.If there is a fault, the screen changes to warn-ing display.Refer to “Warning display list” on page 6-22.
CAUTIONzThe customer is responsible for making surethat periodic inspection and maintenance areperformed.Inspections and maintenance must be per-formed to prevent accidents and malfunc-tions.NOTE
z“---” display cannot be reset when the opera-tion mode is in ON.zWhen “---” is displayed, after a certain dis-tance and a certain period of time, the dis-play is reset and the time until the nextperiodic inspection is displayed.
zIf you accidentally reset the display, we rec-ommend you to consult a MITSUBISHIMOTORS Authorised Service Point.
System check screen
NOTE
zThe system check screen display variesdepending on the customer’s equipment.NOTE
BK0203201EN.book 12 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display
Instruments and controls 6-13
6
E00537600026
This displays the approximate driving range(how many more kilometres or miles you candrive).EV cruising range display (A)This displays the distance that can be traveledwith the remaining power in the drive battery.To t a l c r u i s i n g r a n g e d i s p l a y ( B )This displays the distance that can be traveledwith the remaining power in the drive batteryand the remaining amount of fuel.
E00531201072
This displays the average fuel consumptionfrom the last reset to the present time.There are the following 2 mode settings.Refer to “Changing the reset mode for aver-age fuel consumption” on page 6-16.For information on how to change the aver-age fuel consumption display setting, refer to“Changing the function settings” on page6-15.
EV cruising range display/Total cruising range display
NOTE
zThe driving range may vary depending onthe driving conditions
and habits. Treat the
distance displayed as just a rough guideline. zWhen the drive battery is charged or thevehicle is refueled, th
e cruising range display
is updated. However, if the charge level islow or the refueling amount is small, it can-not be updated correctly. Fully charge thebattery or refill to full tank whenever possi-ble.
zOn rare occasions, the value displayed forthe driving range may change if you areparked on an extremely steep incline. This isdue to the movement of fuel in the tank anddoes not indicate any malfunction.zThe display setting can be changed to thepreferred units (km or miles).Refer to “Changing the function settings” onpage 6-15.zWhen the EV cruising range falls belowapproximately 1 km (1 mile), the EV cruis-ing range display shows “---”.zWhen the total cruising range falls belowapproximately 50 km (30 miles), the totalcruising range disp
lay shows “---”.
Av e r a g e f u e l c o n s u m p t i o n d i s -play
NOTE
NOTE
zThe average fuel consumption display can bereset separately for the auto reset mode andfor the manual reset mode.z“---” is displayed when the average fuel con-sumption cannot be measured or when it is99.9 L/100 km (99.9 miles) or more.zThe initial (default) setting is “Auto resetmode”.zThe average fuel consumption will dependon the driving conditions (road conditions,how you drive, etc.). The displayed fuel con-sumption may vary from the actual fuel con-sumption. Treat the fuel consumptiondisplayed as just
a rough guideline.
zThe memory of the auto reset mode or man-ual reset mode for the average fuel consump-tion display is erased if the auxiliary batteryis disconnected.zThe display setting can be changed to thepreferred units {km/L, mpg (US), mpg (UK)or L/100 km}.Refer to “Changing the function settings” onpage 6-15.
BK0203201EN.book 13 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display6-16 Instruments and controls
6
4. Select the item to change on the menuscreen and change to the desired setting.Refer to the following items for furtherdetails on the operation methods.Refer to “Changing the reset mode foraverage fuel consumption” on page 6-16.Refer to “Changing the fuel consumptiondisplay unit” on page 6-17.Refer to “Changing the temperature unit”on page 6-17.Refer to “Changing the display language”on page 6-18.Refer to “Changing the language coopera-tive control” on page 6-18.Refer to “Operation sound setting” onpage 6-19.Refer to “Changing the time until “RESTREMINDER” is displayed” on page 6-19.Refer to “Changing the turn-signal sound”on page 6-20.Refer to “Returning to the factory set-tings” on page 6-20.
E00522902054
The mode conditions for the average fuelconsumption display can be switchedbetween “Auto reset” and “Manual reset”.1. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from the setting mode screen to themenu screen.Refer to “Changing the function settings”on page 6-15.2. Lightly press the multi information dis-play switch to select “AVG (average fuelconsumption)”.
3. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from A/1 (Auto reset mode) toM/2/P (Manual reset mode), or fromM/2/P to A/1.The setting is changed to the selectedmode condition.zWhen the average fuel consumption isbeing displayed, if you hold down themulti information display switch, theaverage fuel consumption displayed atthat time is reset.zWhen the operation mode is changedfrom ACC or OFF to ON, the mode set-ting is automatically switched from man-ual to auto.Switching to auto occurs automatically. Ifswitching to manual mode is done, how-ever, the data from the last reset is dis-played.zWhen the average fuel consumption isbeing displayed, if you hold down themulti information display switch, theaverage fuel consumption displayed atthat time is reset.
NOTE
zIf the auxiliary battery is disconnected, thesefunction settings are reset from memory andis automatically to the factory settings.
Changing the reset mode for aver-age fuel consumption
Manual reset modeAuto reset mode
BK0203201EN.book 16 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display
Instruments and controls 6-19
6
2. Lightly press the multi information dis-play switch to select “ ” (languagecooperative control).3. Press and hold the multi information dis-play switch to switch from A (languagecooperation enabled) to M (languagecooperation disabled), or from M to A.The setting is changed to the selected con-dition.
E00523400690
Yo u c a n t u r n o f f t h e o p e r a t i o n s o u n d s o f t h emulti information display switch and rheostatillumination button.
1. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from the setting mode screen to themenu screen.Refer to “Changing the function settings”on page 6-15.2. Lightly press the multi information dis-play switch to select “ ” (operationsound setting).3. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from ON (operation sound on) toOFF (operation sound off), or from OFFto ON.The setting is changed to the selected con-dition.
E00523501702
The time until the display appears can bechanged.
NOTE
zThe language display modified with the lan-guage setting can be switched in the follow-ing manner.
•When A (language
cooperation enabled)
has been selected with the language cooper-ative control, the language for theBluetooth
®2.0 interface (if so equipped) is
automatically changed to the languageselected for the multi information display.However, this changing function may notwork depending on the language selectedfor the multi information display.•When M (language c
ooperation disabled)
has been selected with the language cooper-ative control, the language for theBluetooth
®2.0 interface (if so equipped) is
not automatically changed to the languageselected for the multi information display.
zThe language on the disp
lay of the audio sys-
tem (if so equipped) is not automaticallychanged even if you
select A (language
cooperation enabled) of
the language cooper-
ation control.
Operation sound setting
NOTE
NOTE
zThe operation sound setting only deactivatesthe operation sound of the multi informationdisplay switch and rheostat illumination but-ton. The warning di
splay and other sounds
cannot be deactivated.
Changing the time until “REST REMINDER” is displayed
BK0203201EN.book 19 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分