2014 MITSUBISHI OUTLANDER SPORT change time

Reversing sensor system*7-66 Starting and driving
7
Back sensor (vehicles without a towbar)Back sensor (vehicles with a towbar)
E00615801257
The detection areas can be changed as fol-lows:While the operation of the system is stoppedat the “SONAR” switch, push the “SONAR”switch approximately 3 seconds or more, andrelease it. The buzzer sounds twice to indicatethat the detection area has been changed.While the operation of the system is stoppedat the “SONAR” switch, push the “SONAR”switch approximately 3 seconds or more, andrelease it. The buzzer sounds once to indicatethat the detection area has been changed.
E00615900323
In case there is a malfunction in the reversingsensor system, the display for the malfunc-tioning sensor will blink and the warningbuzzer will sound for approximately 5 sec-
Ve h i c l e t o o b s t a c l e
distance
Wa r n i n g d i s -play/sound cycle
Approx. 150 to 80
cm
Intermittent
Approx. 80 to 40 cm Fast intermittentWi t hi n a ppr o x. 40
cm
Continuous
Ve h i c l e t o o b s t a c l e
distance
Wa r n i n g d i s -play/sound cycle
Approx. 150 to 100
cm
Intermittent
Approx. 100 to 60
cm
Fast intermittent
Wi t hi n a ppr o x. 60
cm
Continuous
CAUTIONzThe distances given are to be used for refer-ence only, as errors may be caused by vari-ous factors, such as temperature, humidity,or the shape of the obstacles.
NOTE
zWhen the sensors are detecting differentobstacles at the same time, the informationscreen in the multi information display indi-cates the directions of the obstacles each sen-sors are detecting. However, closer obstaclesare given priority over other detected obsta-cles and the warning buzzer sounds to informyou of closer obstacles.
Changing the detection areas

Ve h i c l e s w i t h a t o w b a rVe h i c l e s w i t h o u t a t o w b a r
NOTE
zThe detection area will not change if youkeep the “SONAR” switch pushed for 10seconds or more.zAfter pushing the “SONAR” switch, revers-ing sensor system operation differs accord-ing to the detection area setting.•Setting when towbar is not equippedWhen the selector lever is moved to the “R”position, the reversi
ng sensor system will
operate even if corner sensor operation wasstopped by pushing the “SONAR” switch.•Setting when towbar is equippedWhen reversing sensor system operationwas stopped by pushing the “SONAR”switch, the reversing sensor system will notoperate until the Plug-
in Hybrid EV System
has been stopped even if the selector leveris moved to the “R” position.To r e s u m e r e v e r s i n g s e n s o r s y s t e m o p e r a -tion, push the “SONAR” switch or stop andrestart the Plug-in Hybrid EV System, andthen move the selector lever to the “R”position.
Reversing sensor system warn-ing display

BK0203201EN.book 66 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Automatic climate control air conditioner
For pleasant driving 8-5
8
E00702801371
Press of the blower speed selectionswitch to increase the blower speed.Press of the blower speed selectionswitch to decrease the blower speed.The selected blower speed will be shown inthe display (A).
E00703001673
Press or of the temperature controlswitch to the desired temperature.The selected temperature will be shown in thedisplay (A).
7- Demister switch8- AUTO switch9- Rear window demister switch
m P.6-53
10- OFF switch11 - P assen ge r ’s side tem pera tu re disp la y
m P.8-5
12- DUAL indicator13- Mode selection display14- Driver’s side temperature display
m P.8-5
15- Air conditioning indicator16- Blower speed display
NOTE
zThere is an interior air temperature sensor(A) in the illustrated position.Never place anything on
top of the sensor,
since doing so will prevent it from function-ing properly.zSince the air conditioning operation is con-trolled while the ECO mode is operating,you may feel that effectiveness of the airconditioner is weak.m ECO mode switch P.6-46
zEven if the ECO mode is operating, you canselect normal operation of the air condi-tioner.On vehicles equipped
with Mitsubishi Multi-
Communication System (MMCS), screenoperations can be used to change the setting.Refer to the separate
owner’s manual for
details.zIn extreme cold, the air conditioning controlpanel screen may operate sluggishly. Thisdoes not indicate a problem.It will disappear when the vehicle interiortemperature rises to
a normal temperature.
zA sound will be made every time you pushall the switches.
Blower speed selection switch
NOTE
1- Increase2- DecreaseTe m p e r a t u r e c o n t r o l s w i t c h
BK0203201EN.book 5 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Automatic climate control air conditioner8-6 For pleasant driving
8
The settings described above are the factorysettings.The air selection and air conditioningswitches can be customised (function settingchanged), and the automatic switching of out-side air and the air conditioner according tooperating conditions can be changed asdesired.For further information, we recommend youto consult a MITSUBISHI MOTORS Author-ised Service Point.Refer to “Customising the air conditioningswitch” on page 8-8.Refer to “Customising the air selection” onpage 8-7.The driver’s side and the passenger’s sidetemperature can be controlled independently.At this time, the “DUAL” indicator will beshown in the display (A).
zSynchronized modeIf the driver’s side temperature controlswitch is pressed, the passenger’s sidetemperature will also be controlled to thesame setting temperature as the driver’sside.zDual modeIf the passenger’s side temperature con-trol switch is pressed under synchronizedmode, the system will switch to dualmode. In dual mode, the driver’s side andthe passenger’s side temperature can beset separately by using each temperaturecontrol switch.Press the AUTO switch to return to syn-chronized mode.
E00703401808
To change the air selection, simply press theair selection switch.
NOTE
zThe temperature value of air conditioner isswitched in conjunction
with outside temper-
ature display unit of the multi informationdisplay.Refer to “Changing the temperature unit” onpage 6-17.zWhile the engine coolant temperature is low,the temperature of th
e air from the heater
will not change instantly, even if you haveselected warm air with the switch.To p r e v e n t t h e w i n d s c r e e n a n d w i n d o w sfrom fogging up, the ventilator mode will bechanged to “ ” and the blower speed willbe reduced while the system is operating inthe AUTO mode.zWhen you feel that it is hot or cold to the set-ting temperature, it is possible to adjust sothat you can feel more comfortable.For further information, we recommend youto consult a MITSUBISHI MOTORSAuthorised Service Point.zWhen the temperature is set to the highest orthe lowest, the air selection and the air condi-tioner will be automatically changed as fol-lows.Also, if the air selec
tion is operated manually
after an automatic changeover, manual oper-ation will be selected.•Quick Heating (When the temperature is setto the highest setting)Outside air will be introduced and the airconditioner will stop.
•Quick Cooling (When the temperature is setto the lowest setting)Inside air will be r
ecirculated and the air
conditioner will operate.
zWhen the air conditioner is set to quick heat-ing, the engine starts
running (except vehi-
cles with electric heater).

Automatic climate control air conditioner
For pleasant driving 8-7
8
zOutside air: Indicator lamp (A) is OFFOutside air is introduced into the passen-ger compartment.zRecirculated air: Indicator lamp (A) is ONAir is recirculated inside the passengercompartment.
E00739600022
Functions can be changed as desired, asstated below.
zEnable automatic air controlWhen the AUTO switch is pressed, the airselection switch is also controlled auto-matically.zDisable automatic air controlEven when the AUTO switch is pressed,the air selection switch is not controlledautomatically.zSetting change methodHold down the air selection switch forabout 10 seconds or more.•When the setting is changed from enableto disable3 sounds are emitted and the indicatorlamp flashes 3 times.•When the setting is changed from disa-ble to enable2 sounds are emitted and the indicatorlamp flashes 3 times.On vehicles equipped with MitsubishiMulti-Communication System (MMCS),screen operations can also be used tochange the setting. Refer to the separateowner’s manual for details.
CAUTIONzUse of the recirculation position for anextended time may cause the windows to fogup.
NOTE
zNormally, use the outside position to keepthe windscreen and side windows clear andquickly remove fog or frost from the wind-screen.If high cooling performance is desired, or ifthe outside air is dusty
or otherwise contami-
nated use the recirculation position. Switchto the outside position periodically toincrease ventilation so that the windows donot become fogged up.zWhen the engine coolant temperature rises toa certain level, the air selection is automati-cally switched to the recirculation positionand the indicator lamp (A) comes on. At thistime, the system will not switch to the out-side position even if the air selection switchis pushed.zWhen the outside air temperature is high, thesystem will not switch to the outside positioneven the air selection switch is pressed if theair conditioner is operating. This is to protectthe air conditioner compressor and is not afailure.

Automatic climate control air conditioner8-8 For pleasant driving
8
E00702600037
When the AUTO switch is pressed, the indi-cator lamp (A) comes on and the mode selec-tion (except for “ ”), blower speedadjustment, recirculated/outside air selection,temperature adjustment, and air conditionerON/OFF status are all controlled automati-cally.
E00703502327
Push the switch to turn the air conditioner on,the “ ” indicator will be shown in the dis-play (A).Push the switch again to switch it off.
E00739700023
Functions can be changed as desired, asstated below.zEnable automatic air conditioning controlWhen the AUTO switch is pressed, or thetemperature control switch is set to theminimum temperature, the air condition-ing switch is controlled automatically.zDisable automatic air conditioning controlThe air conditioning switch is not con-trolled automatically as long as the airconditioning switch is not operated.zSetting change methodHold down the air conditioning switch forabout 10 seconds or more.•When the setting is changed from enableto disable3 sounds are emitted and the “ ” indi-cator flashes 3 times.•When the setting is changed from disa-ble to enable2 sounds are emitted and the “ ” indi-cator flashes 3 times.
zWhen the demister switch is pressed, inorder to prevent misting of the windows theventilator automatically switches to outsideair even if “Disable automatic air control” isset.
AUTO switch
NOTE
Air conditioning switch
NOTE
zIf a problem is detected in the air condition-ing system, the “ ” indicator blinks. Pressthe air conditioning switch once to turn it off,then once more to turn it back on. If the “ ”indicator does not blink for a while, there isnothing wrong. If it starts to blink again, werecommend you to have it checked.

Automatic climate control air conditioner
For pleasant driving 8-9
8
On vehicles equipped with MitsubishiMulti-Communication System (MMCS),screen operations can also be used tochange the setting. Refer to the separateowner’s manual for details.
E00702700038
Push the switch to turn off the air condition-ing system.
E00703300031
Each time the MODE switch is pressed, themode changes to the next one in the follow-ing sequence: “ ”
m “ ”
m “ ”
m
“”
m “ ”. The selected mode is shown
in the display (A). (Refer to “Mode selection”on page 8-2.)
E00703901063
When this switch is pressed, the modechanges to the “ ” mode. The indicatorlamp (A) will come on. The selected mode isshown in the display (B). (Refer to “Modeselection” on page 8-2.)
NOTE
zThe factory setting is “Enable automatic airconditioning control”.zWhen the demister switch is pressed, inorder to prevent misting of the windows theair conditioner operates automatically even if“Disable automatic air conditioning control”is set.
OFF switch
MODE switch Demister switch
NOTE
zWhen the demister switch is pressed, the airconditioning system automatically operatesand outside air (as oppos
ed to recirculated
air) is selected. This automatic switchingcontrol is carried out to prevent misting ofthe windows even if “D
isable automatic air
conditioning control” or
“Disable
automatic
air control” is set. (Refer to “Customising theair conditioning switch” on page 8-8, “Cus-tomising the air selec
tion” on page 8-7.)
zWhen the demister switch is pressed, theengine may start running (except vehicleswith electric heater).
BK0203201EN.book 9 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Important operation tips for the air conditioner
For pleasant driving 8-11
8
1. Push the demister switch to change to the“” position.2. Set the blower to the maximum speed.3. Set the temperature to the highest posi-tion.
E00704400127
When driving on a dirt road, adjust the venti-lation controls as follows:
1. Set the air selection switch to the outsideposition.2. Select the MODE switch to the desiredposition.3. Select the temperature control switch tothe desired position.4. Select the desired blower speed (thehigher the better).5. Ensure all windows are closed (to pressur-ise the cabin).
If you are driving behind another vehicle on adirt road and/or the outside air is dusty orcontaminated, set the air selection switch tothe recirculation position. During periods ofextended driving, ventilate the vehicle’s inte-rior by occasionally setting the switch fromthe recirculation to the outside position.
E00708302102
zPark the vehicle in the shade.Parking in the hot sun will make the vehi-cle inside extremely hot, and it willrequire more time to cool the interior.If it is necessary to park in the sun, openthe windows for the first few minutes ofair conditioning operation to expel the hotair.
zClose the windows when the air condi-tioner is in use. The entry of outside airthrough open windows will reduce thecooling efficiency.zTo o m u c h c o o l i n g i s n o t g o o d f o r t h ehealth. The inside air temperature shouldonly be 5 to 6 °C below the outside airtemperature.zWhen operating the system, make sure theair intake, which is located in front of thewindscreen, is free of obstructions such asleaves and snow. Leaves collected in theair-intake plenum may reduce air flowand plug the plenum water drains.zTo o m u c h c o o l i n g / h e a t i n g c a n a f f e c t t h eEV cruising range, so maintain an appro-priate temperature to extend the EV cruis-ing range.
If the air conditioner seems less effective thanusual, the cause might be a refrigerant leak.We r e c o m m e n d y o u t o h a v e t h e s y s t e minspected.The air conditioning system in your vehiclemust be charged with the refrigerant HFC-134a and the lubricant POE MA68EV.

Audio Quality and Volume Balance Adjustment
For pleasant driving 8-35
8
E00738501076
Yo u c a n c h a n g e t h e c o n t e n t o f t h e d i s p l a yindicator.Press the DISP key to switch the display con-tent.Each time the DISP key is pressed, the dis-play content changes.This switches in the order “Disc title”, “Tracktitle”, and “Operating status”.
This switches in the order “Folder title”, “Filetitle”, and “Operating status”.Hold down the DISP key.This switches the ID3tag display.[DISP] Each time the key is pressed, thisswitches in the order “Album name”, “Trackname”, “Artist name”, “Genre name”
*, and
“Operating status”.
E00738901038
This switches in the order “Albums”, “Trackname”, “Artist name”, “Genre name”
*, and
“Operating status”.
E00739001023
Operating details are the same as in “DuringiPod Playback” (P.8-35).
E00738200021
Change audio quality settings.
Change the Display Mode
CAUTIONzThe operation of changing display contentsmay impede safe driving, therefore checksafety before operation.NOTE
zUp to 11 characters may be displayed at onetime. To display 12 or
more characters, press
the PAGE key, and subsequent characterswill be displayed.
During CD-DA playback
NOTE
zIf there is no text information to display, then“NO TITLE” is displayed.
During MP3/WMA/AAC Play-back
NOTE
zIf there is no text information to display, then“NO TITLE” is displayed.
Display the ID3tag *:Displayed when playing back audio fileson a USB device.
NOTE
zDuring display of the ID3tag, hold down theDISP key to switch to the folder title display.zThe genre name displa
y may not be possible.
During iPod Playback
NOTE
zIf there is no text information to display, then“NO TITLE” is displayed.zDisplayed genre name in equipment by type.zThe genre name display may not be possible.
During Bluetooth
® 2.0 Audio Play-
back Audio Quality and Volume Balance Adjustment
BK0203201EN.book 35 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分