2014 MITSUBISHI OUTLANDER SPORT change time

Acoustic Vehicle Alerting System (AVAS)7-24 Starting and driving
7
When the battery save switch is turned onwhile driving in the battery charge mode, themode changes to the battery save mode.If the battery charge switch is pressed, themode is returned to the battery charge mode.
E00631601051
The Acoustic Vehicle Alerting System(AVAS) is device that uses sound to alertpedestrians of the presence of the vehicle.The system operates when the vehicle speedis about 35 km/h or less and the engine is notrunning.The sound starts when the AVAS is operatedwith the following conditions.zWhen the vehicle speed is about 3 km/h orless with engine not running and the brakepedal is not depressed.
zSince the engine will start also in the vehi-cle stops if the batt
ery charge switch is
pressed, do not use it for the around of thegarage or the vehicle
in the situation such
as snow lay etc. while stopping and park-ing.Doing so, the exhaust gas enters into thevehicle and there is a possibility of becom-ing carbon monoxide poisoning.Be sure to use at the well-ventilated place.zDo not use the battery charge switch nearflammable which a drie
d grass or a paper
etc..There is a possibility of becoming a firebecause the exhaust pipe is high tempera-ture.CAUTIONzI left something so as to close the front of thevehicle, do not operate the battery chargerswitch.NOTE
zUse the battery charge switch before theuphill climb.zEven if the battery charge switch is pressed,the battery charge mode may not be activateddepending on the remaining drive batterycapacity or the remaining fuel quantity andthe control.WA R N I N G
zIt is recommended to use the battery charg-ing switch before at least 20 minutes, if youclimb to continue the speed of more than100km/h or the long slope (gradient of morethan 4 %) is expected. (According to a tow-ing weight, it may not be able to continue thespeed.)zWhen using the battery charge switch a longtime with vehicle
stopping under high tem-
perature, it may not be charged.zThe charging time close to full charge of thedrive battery becomes longer depending onthe condition of the drive battery, a drivingcondition or a environment.zThe engine may stop near full charge.zIf you press the battery charge switch, inorder to generate elec
tricity using gasoline,
the fuel consumption will suffer.We r e c o m m e n d y o u u s e c o n s i d e r e d e n v i r o n -ment.zWhen the engine is started while parking,there is a risk of penalties related to idlingstop ordinance.Yo u s h o u l d u s e t h e b a t t e r y c h a r g e s w i t c hwith confirming to the relevant municipality.Also, if the engine is started, in order to con-sume gasoline, be careful not to cause nofuel.NOTE
When the Battery save switch is ON Acoustic Vehicle Alerting System (AVAS)
BK0203201EN.book 24 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Adaptive Cruise Control System (ACC)*7-50 Starting and driving
7
There are two ways to increase the set speed.The set speed increases by 1 km/h every timeyou push up the “RES +” switch while theACC control is working. If you hold theswitch pushed up, the set speed increases in 5km/h increments.
When the accelerator pedal is depressedwhile driving with the ACC control working,you can accelerate the vehicle temporarilybeyond the presently set speed.At the point where the vehicle speed is raisedto your desired speed, push down and releasethe “SET -” switch; the new speed is then setin the system.
There are two ways to decrease the set speed.The set speed decreases by 1 km/h every timeyou push down the “SET -” switch while theACC control is working. If you hold theswitch pushed down, the set speed decreasesin increments of 5 km/h.
To i n c r e a s e t h e s e t s p e e d

By using the “RES +” switch:
NOTE
zThere is some time lag between the setting toa new speed and actually accelerating to thatspeed.zSpeed setting operation is possible even inpresence of a vehicle in front. In this case,however, the set speed alone increases with-out actual acceleration taking place.
zWhen the switch is held pushed, a buzzersounds every time the set speed changes.CAUTIONzThe setting speed should be set up the suita-ble speed according to a situation.
By using the accelerator pedal:
NOTE
CAUTIONzThe ACC braking control and proximityalarm functions will not work while theaccelerator pedal is depressed.NOTE
zThe set speed indication on the display turnsto “---” when the accelerator pedal isdepressed. This indication remains as long asthe pedal is in a depressed position.zThe ACC control at the original set speedresumes as soon as you release the accelera-tor pedal. Under certain conditions, however,the braking control and alarming functions ofthe ACC may not work for a short while afterreleasing the accelerator pedal.zSet speed adjustment is impossible while theaccelerator pedal is in a depressed position.
To d e c r e a s e t h e s e t s p e e d

By using the “SET -” switch:
BK0203201EN.book 50 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Adaptive Cruise Control System (ACC)*
Starting and driving 7-51
7
If you depress the brake pedal while the ACCcontrol is working, the control is cancelled,allowing you to decelerate the vehicle. At the point where the vehicle slows down toyour desired speed, push down the “SET -”switch; the new speed is then set in the sys-tem.
Simply depress the accelerator pedal to tem-porarily accelerate the vehicle. Releasing thepedal automatically slows down the vehicleto the set speed and the ACC restarts its con-trol.
NOTE
zThere is some time lag between the setting toa new speed and actually decelerating to thatspeed.zIf there is a vehicle in front and your vehicleis following that vehicle at a speed lowerthan the set speed, the set speed alonedecreases with no actual deceleration takingplace.zWhen the switch is held pushed, a buzzersounds every time the set speed changes.CAUTIONzThe setting speed should be set up the suita-ble speed according to a situation.
By using the brake pedal:
NOTE
zThe ACC control is ca
ncelled if you depress
the brake pedal and the ACC control doesnot resume even when you release the pedal.
To t e m p o r a r i l y a c c e l e r a t e t h e v e h i -cle
CAUTIONzThe ACC braking control and proximityalarm functions will not work while theaccelerator pedal is depressed.zThe setting speed should be set up the suita-ble speed according to a situation.
BK0203201EN.book 51 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Adaptive Cruise Control System (ACC)*7-54 Starting and driving
7
After cancelling the ACC control (i.e. placingthe system in the ‘standby state’) by pressingthe “CANCEL” switch or depressing thebrake pedal, you can resume the ACC controlat the originally set speed if you push up the“RES -” switch.
Every time you press the following distancesetting switch, the setting changes sequen-tially through three options “Long”, “Middle”and “Short”, cycling back to “Long” after“Short”. The distance setting is reset whenthe operation mode is set to “OFF” or whenthe ACC is set to “OFF,” and is automaticallyset to “long” when you set the ACC to “ON”next time.
Following distance setting: “Long”Following distance setting: “Middle”Following distance setting: “Short”If you hold the “ACC ON/OFF” switchpressed with the operation mode set to “ON”and the ACC in the ‘OFF state’, the cruisecontrol is activated. The information screenof the multi-information display then changesto the cruise control screen and a buzzersounds at the same time.Cruise control is turned off if you set theoperation mode to “OFF”.
NOTE
zPressing the switch turns off the ACC even ifit is engaged.zThe set speed is cancelled when the ACC isturned off or the operation mode is set to“OFF”.zIf the ACC is in the ‘ON state’ when theoperation mode is set to “OFF”, the system isset to the ‘OFF state’ when the operationmode is set to
“ON” ne
xt time.
To r e s u m e t h e c o n t r o l

NOTE
zThe conditions to be met before the ACCcontrol can be resumed are the same as thosefor starting the ACC control.
To c h a n g e t h e f o l l o w i n g d i s t a n c e setting

NOTE
zThe following distance varies as a functionof the speed; the fast
er the set speed, the
longer the following distance.
To a c t i v a t e c r u i s e c o n t r o l ( a u t o -matic speed control)

BK0203201EN.book 54 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Forward Collision Mitigation System (FCM)*
Starting and driving 7-57
7
zIn the following situations, the system pro-vides neither cont
rol nor alarming.
•The vehicle in front of your vehicle is mov-ing at a speed much lower than your vehi-cle’s speed.•When a vehicle suddenl
y cuts in front of
your vehicle.•When the distance from a vehicle in front isextremely short.•To an oncoming vehicle.•When your vehicle’s speed is much lower.•When the selector leve
r is other in the “D”
(DRIVE) position.•When the system is faulty (if the systemself-detects any fault, the “FCM SERVICEREQUIRED” message is indicated and the“FCM OFF” indicator lights up on theinformation screen of the multi-informationdisplay).If the message remains after the operationmode has been turned to the “OFF” positionand then turned back to the “ON” position,contact a MITSUBISHI MOTORS Author-ised Service Point.CAUTION
zBraking function will not work in the follow-ing situations.•Your vehicle is driving at approximately 30km/h or faster while the vehicle in front isstationary or moving extremely slowly.•The ASC is OFF.zThe forward collision warning functionand/or the FCM braking function may notactivate in the following situations.•When a motorcycle, bicycle, pedestrian,animal, fallen objects, or anything otherthan a vehicle is present in front of yourvehicle.•When a vehicle suddenly appear just infront of your vehicle.•When a vehicle cuts in front of your vehiclevery closely.•When the vehicle in front is offset to theleft or right.•When the vehicle in front is towing atrailer.•A freight trailer that is not carrying a con-tainer.•The vehicle has a pr
otruding load from the
carrier.•The vehicle has a low vehicle height.•The vehicle has an extremely high groundclearance.•When there is a different object near thevehicle.CAUTION
•When driving on a road with many and suc-cessive curves, including when passingtheir entrances and outlets.•When accelerating and deceleratingquickly.•When the system recognizes driver’s steer-ing, accelerating, braking or gear shiftingactions as evasive actions to avoid colli-sion.•When driving on a road with steep andalternating up
and down slopes.
•When a road surface is surging, and there isunevenness.•When being driven in a tunnel.•When the your vehicle
changed lanes, and
your vehicle approached immediatelybehind the vehicle in front.•During a certain time after your vehicleturns left or right.•When you are carrying extremely heavyloads in the rear seats or luggage area.•After the Plug-in Hybrid EV System hasbeen running for an extended period oftime.•Under adverse weather conditions (rain,snow, sand storms, etc.)
*
•When the cover part in
front of the sensor
and the sensor become dirty or adheringsnow and ice
*.
•When water, snow or sand on the road areextorted by the vehicle in front or anoncoming vehicle
*.
CAUTION
BK0203201EN.book 57 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Forward Collision Mitigation System (FCM)*
Starting and driving 7-59
7
E00635601062
This switch is used to turn on and off theFCM and also to select your desired collisionalarm timing.When the switch is held pressed, the ON/OFFstate of the FCM changes from ON to OFFand vice versa. If you give the switch a shortpress with the FCM in the ON state, you canchange the collision alarm timing.
Yo u c a n s w i t c h t h e s y s t e m f r o m O F F t o O Nor ON to OFF if you hold the FCM ON/OFFswitch pressed when the operation mode isset to “ON”.Once the system is turned on, a buzzersounds, the information screen of the multi-information display shows the collision alarmtiming currently selected, and the “FCMOFF” indicator on the screen goes out.When you turn off the system, a buzzer soundand, at the same time, the “FCM OFF” mes-sage appears on the screen and the “FCMOFF” indicator comes on.Cycling the operation mode to ON will setthe FCM back ON.
•When installing the spare tyre for emer-gency.•When tyre chains are attached.zImproperly handling the system componentsmay result in such problems as degraded sen-sor performance and ultimately in an acci-dent. Be sure to take the followingprecautions to keep the system in good oper-ating conditions.•Avoid application of
strong shock loads to
the sensor and never tamper with or removethe sensor mounting screws.• The cover in front of the sensor and the sen-sor should be kept clean.•Do not cover the sensor mounted area ofthe vehicle or the sensor cover with asticker or anything such as a grill guardetc..•The sensor front cove
r should not be modi-
fied or painted.•Avoid using different
size tyres from those
specified and maintain even tyre wear.•Do not modify the suspension of your vehi-cle.
zIf the sensor mounted area of the vehicle isdeformed due to an acci
dent or some other
causes, turn off the system and please con-tact a MITSUBISHI MOTORS AuthorisedService Point.CAUTION
NOTE
zA sound will be heard during the activationof automatic braking, this is a function of thebrake control and is not abnormal.
FCM ON/OFF switch

To t u r n o n / o f f t h e s y s t e m

BK0203201EN.book 59 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Lane Departure Warning (LDW)*7-60 Starting and driving
7
Give a short press to the FCM ON/OFFswitch to change the timing at which the fron-tal collision alarm is triggered. Every timeyou press the switch, the alarm timingchanges alternately between “FAR” (earlieralarming) and “NEAR” (later alarming).As you make selection, the selected alarmtiming is displayed on the information screenof the multi-information display. Even afterturning off the FCM or setting the operationmode to “OFF”, the sy
stem retains your last
selected alarm timing in memory.When “NEAR” is selectedWhen “FAR” is selected
E00635701021
By recognizing through a camera (A) the lanein which your vehicle is running, LDW givesyou warning when your vehicle is likely todrift from its lane with an audible alarm and avisual alarm displayed on the informationscreen of the multi-information display.
E00635801022
The indication on the information screen ofthe multi-information display changes as fol-lows depending on the state of the system.When you set the operation mode to “ON”,the “LDW” indicator appears on the informa-tion screen of the multi-information display,showing that the system is placed in the ‘ONstate’.
To c h a n g e a l a r m t i m i n g

CAUTIONzFor the FCM brake prefill, the FCM brakeassist and the FCM braking functions, thefunction triggering timing cannot bechanged.
Lane Departure Warning (LDW)
*
How to operate LDW

Tu r n i n g o n t h e s y s t e m

BK0203201EN.book 60 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Reversing sensor system*7-64 Starting and driving
7
Depending on whether the vehicle isequipped with a towbar, you can change thereversing sensor system between the standardmode and the towbar mode. The towbar modechanges the system to exclude the area inwhich the towbar is mounted from the detec-tion areas.The detection areas are within approximately60 cm (A) from the corner sensors, 150 cm(B) from the back sensors, and 60 cm (C) orless from the ground surface, excluding thearea approximately 10 cm (D) from theground surface.
The detection areas are within approximately60 cm (A) from the corner sensors, 150 cm(B) from the back sensors, and 60 cm (C) orless from the ground surface, excluding thearea approximately 10 cm (D) from theground surface. The non-detection areas (E)are within approximately 20 cm (F) from thebumper.
For information on how to change the detec-tion areas, please refer to “Changing thedetection areas” on page 7-66.
Reversing sensor system detection areas

Ve h i c l e s w i t h o u t a t o w b a r
Ve h i c l e s w i t h a t o w b a r
NOTE
zIf the rear bumper has been exposed to animpact, the corner or back sensors may failand prevent the system from functioningproperly. Have the vehicle inspected at aMITSUBISHI MOTORS Authorised ServicePoint.zThe sensors do not detect objects located inthe area directly below or near the bumper. Ifthe height of an object is lower than themounted position of the corner or back sen-sors, the sensors may not continue detectingit even if they detected it initially.CAUTIONzThe reversing sensor
system may not operate
properly under the following conditions:•The sensors or surroundings are coveredwith ice, snow, or mud.•The sensors are frozen.•The system receives ultrasonic noise fromother sources (the horns
of other vehicles,
motorcycle engines, brakes, radios, pouringrain, splashing water,
snow traction device
(tyre chains), etc.).•The sensors are extremely hot or cold(while the vehicle is parked for a longperiod of time under a blazing sun or incold weather).
BK0203201EN.book 64 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分