2014 MITSUBISHI OUTLANDER PHEV Owner's Manual (in English)

Mass groupSize classFixture
Vehicle ISOFIX positionsRecommended
Child Restraint
Systems *2UN-R44 Appro-
val No.
Front passengerRear out-boardActivated air- bagDeactivated
Airbag *1CISO/R3XXILfor ALL area):
MZ314417I - 9 to 18 kgDISO/R2XXILG 0/1 S (Child re-straint system for East area):
MZ314390E
G 0/1 S (Child re- straint system for
Central-South area): MZ314390CS
G 0/1 S (Child re- straint system for North area):
MZ314390N
RWF ISOFIX
BASE (Rearward
facing ISOFIX base for ALL area):MZ314417
E4-04443718CISO/R3XXIL
BISO/F2XIUFIUF——B1ISO/F2XXIUF, ILIUF, ILDUO plus:
MZ313045E1-04301133AISO/F3XIUFIUF——II - 15 to 25 kg XILILKIDFIX:
MZ314804E1-04301198III - 22 to 36 kg XILIL
Child restraint
5-19OGGE14E5Seats and seat belts5

*1:With front passenger’s airbag deactivated by means of front passenger’s airbag ON-OFF switch.*2:MITSUBISHI MOTORS Europe B.V. reserves the right to changes without any prior announcement.
For detailed information, consult your MITSUBISHI MOTORS Authorized Service Point.CAUTIONl When installing a child restraint system, remove the head restraint from the seat.
l When installing a child restraint system on the rear outboard seat, adjust the seatback angle to 4 steps forward from the most reclined position.
l A rearward facing child restraint system of R2/R3 is not recommended for front passenger seat because driver’s visibility is obstructed.Definition of characters the above table:
l
IUF- Suitable for ISOFIX forward child restraint systems of universal category approved for use in the mass group.
l IL- Suitable for particular ISOFIX child restraint systems of the categories for “specific vehicles”, “restricted”, or “semi-universal”, ap-
proved for this type of vehicle.
l X- ISOFIX position not suitable for ISOFIX child restraint systems in this mass group.

Suitability for various seating positions
E00406802575Mass group
Seating position
Recommended Child Restraint Systems *2UN-R44 Approval
No.
Front passenger
Rear outboardRear centreActivated airbagDeactivated Air-
bag*10 - Up to 10 kgXUUX——0+ - Up to 13 kgXU, LU, LXBABY-SAFE plus:
MZ314393E1-04301146I - 9 to 18 kgXU, LU, LXKING plus:MZ314451E1-04301203
Child restraint
5-20OGGE14E5Seats and seat belts5

Mass group
Seating position
Recommended ChildRestraint Systems *2UN-R44 Approval
No.
Front passenger
Rear outboardRear centreActivated airbagDeactivated Air-
bag*1DUO plus:
MZ313045E1-04301133G 0/1 S (Child re-
straint system for East area): MZ314390EG 0/1 S (Child re-straint system for
Central-South area): MZ314390CS
G 0/1 S (Child re- straint system for North area):
MZ314390N
E4-03443416
II - 15 to 25 kgXU, LU, LXKID plus: MZ314250 KIDFIX: MZ314804E1-04301169
E1-04301198III - 22 to 36 kgXU, LU, LX*1 :With front passenger’s airbag deactivated by means of front passenger’s airbag ON-OFF switch*2:MITSUBISHI MOTORS Europe B.V. reserves the right to changes without any prior announcement.
For detailed information, consult your MITSUBISHI MOTORS Authorized Service Point.
Child restraint
5-21OGGE14E5Seats and seat belts5

CAUTIONlWhen installing a child restraint system, remove the head restraint from the seat.
l When installing a child restraint system on the front passenger seat, adjust the front seatback angle to 2 steps rearward from the first locking position.
l When installing “KING plus” of recommended child restraint on the front passenger seat, adjust the front seatback angle to 4 steps rearward from the first
locking position.Definition of characters the above table:
l U- Suitable for “universal” category restraints approved for use in this mass group.
l L- Suitable for particular child restraint systems. See the above table of “Recommended Child Restraint Systems”.
l X- Seat position not suitable for children in this mass group.

Child restraint
5-22OGGE14E5Seats and seat belts5

Installing a child restraint sys-tem to the lower anchorage (ISOFIX child restraint mount-ings) and tether anchorage
E00406901944
Lower anchorage location
Your vehicle’s front passenger seat and rear seat is fitted with lower anchorages for at-
taching a child restraint system with ISOFIX mountings.
Tether anchorage location
Your vehicle has 3 child restraint anchoragepoints on the backside of the front passenger seat and rear seats. These are for securing a
child restraint system tether strap to each of the 3 seating positions in your vehicle.
WARNINGl Child restraint anchorages are designed
to withstand only those loads imposed by
correctly fitted child restraints. Under no circumstances are they to be used for adult seat belts, harnesses, or for attach-
ing other items or equipment to the vehi- cle.
Child restraint system with
ISOFIX mountings
The child restraint system is designed only
for seats that incorporate lower anchorages.
Retain the child restraint system using the lower anchorages.
It is not necessary to retain the child restraint
system using the vehicle’s seat belts.
A- Child restraint system connectors
Child restraint
5-23OGGE14E5Seats and seat belts5Front passenger seat
Rear seat Front passenger seat Rear seat

To install
1.Remove any foreign material in or
around the connectors and ensure the ve-
hicle seat belt is in its normal storage po-
sition.
2. Remove the head restraint from the loca-
tion in which you wish to install a child
restraint.
Refer to “Head restraints” on page 5-05.
3. When installing a child restraint system
in the front passenger seat, adjust seat
slide to its most rearward position.
4. Push the child restraint system’s connec-
tors (A) into the lower anchorages (B) in accordance with the instructions provi-
ded by the child restraint system’s man-
ufacturer.
For easier access to the rear seat lower
anchorage, the rear seatback may be re- cline rearward. After it is security fas-
tened, adjust the seatback to 4 steps for- ward from most reclined position.
A- Connector B- Lower anchorage
C- Vehicle seat cushion
D- Vehicle seatback
If your child restraint system has a sup- port leg, make sure that there is a sup-
port leg at the stable position on the floor. If your child restraint system re-
quires the use of a tether strap, fasten the
tether strap in accordance with step 5.
5. Latch the tether strap hook (E) of the
child restraint system to the tether an-
chorage bar (F) and tighten the top tether strap hook so it is securely fastened.NOTEl If it is difficult to latch the tether strap hook
in the rear seat, turn the hook sideways.
6. Push and pull the child restraint system
in all directions to be sure it is secure.
Child restraint
5-24OGGE14E5Seats and seat belts5 Front passenger seat
Rear seat

To remove
Remove the child restraint system in accord-
ance with the instructions provided by the
child restraint system’s manufacturer.
Installing a child restraint sys-
tem to a 3-point type seat belt (with emergency locking mech-anism)
E00408701816
Installation:
1. Put a child restraint system on the seat in
which you wish to install it, and remove
the head restraint from the seat.
Refer to “Head restraints” on page 5-05.
2. When installing a child restraint system
in the front passenger seat, adjust seat slide to its most rearward position and
adjust the front seatback angle to 2 steps
rearward from the first locking position.
3. Route the belt through the child restraint
according to the child restraint system
manufacturer’s instructions, then insert
the latch plate into the buckle.
4. Remove all slack of a lap belt by pulling
the webbing through the belt’s adjust-
ment feature.
3-point type seat belt requires no length adjustment, remove all slack by usingthe locking clip.
5. If your child restraint system has a sup-
port leg, make sure that there is a sup-
port leg at the stable position on the floor.
6. Before putting the child in the restraint,
push and pull the restraint in all direc- tions to be sure it is secure. Do this be-
fore each use.WARNINGl For some types of child restraint, the lock-
ing clip (A) should be used to help avoid
personal injury during a collision or sud- den manoeuvre.
It must be fitted and used in accordance with the child restraint manufacturer’s
instructions.
The locking clip must be removed when the child restraint is removed.Seat belt inspection
E00406300576
l Check the belts for cuts, worn or frayed
webbing and for cracked or deformed metallic parts. Replace the belt assembly
if it is defective.
l A dirty belt should be cleaned with neu-
tral detergent in warm water. After rins-
ing in water, let it dry in the shade. Do
not attempt to bleach or re-dye the belts
because this will affect their characteris-
tics.WARNINGl We recommend you to have all seat belt
assemblies including retractors and at- taching hardware inspected after any col- lision. We recommend that seat belt as-
semblies in use during a collision be re- placed unless the collision was minor and
the belts show no damage and continue to operate properly.
l Do not attempt to repair or replace any
part of the seat belt assemblies; we recom- mend you to have this work done by aMITSUBISHI MOTORS Authorized
Service Point. Incorrect repair or replace- ment could reduce the effectiveness of the
belts and could result in serious injury in
the event of a collision.
Seat belt inspection
5-25OGGE14E5Seats and seat belts5

WARNINGlOnce the pretensioner has been activated,
it cannot be re-used.
It must be replaced together with the re- tractor.Supplemental restraint
system (SRS) - airbag E00407203254
The information for SRS airbags includes im-
portant information concerning the driver’s and front passenger’s airbags, the driver’s knee airbag, the side airbags and the curtain
airbags.

The SRS driver and front passenger airbags are designed to supplement the primary pro-
tection of the driver and front passenger side
seat belt systems by providing those occu- pants with protection against head and chestinjuries in certain moderate-to-severe frontal
collisions.

The SRS driver’s knee airbag is designed to supplement the primary protection of the
driver’s seat belt system. It can reduce the forward movement of the driver’s lower legs and provide increased overall body protectionin certain moderate-to-severe frontal colli- sions.

The SRS side airbags are designed to supple-
ment properly worn seat belts and provide the
driver and front passenger with protection against chest injuries in certain moderate-to-
severe side impact collisions.

The SRS curtain airbags are designed to sup-
plement properly worn seat belts and provide the driver and passenger with protection
against head injuries in certain moderate-to-
severe side impact collisions.

The SRS is NOT a substitute for the seat
belts. To ensure the maximum protection dur- ing all types of collisions and accidents, all occupants, including the passengers as well
as the driver, must wear their seat belts.How the Supplemental Re-
straint System works
E00407302825
The SRS includes the following components:
1- Airbag module (Driver)
2- Front passenger’s airbag indicator
3- Airbag module (Passenger)
4- Driver’s knee airbag module
5- Front passenger’s airbag ON-OFF switch
6- Side airbag modules
7- Curtain airbag modules
Only when the operation mode of the power switch is in ON, the airbags will operate.
Supplemental restraint system (SRS) - airbag
5-26OGGE14E5Seats and seat belts5