2013 AUDI TT Owner´s Manual

remain continuous ly illuminated . This se ­
quence will continue upon subsequent vehicle
start-ups as long as the ma lfunction ex ists.
When the malfunct ion indicator is ill uminat­
ed, the system may not be able to detect or
signa l low tire pressure as intended. TPMS
malfunct ions may occur for a variety of rea­
sons, including the installat ion of replace­
ment or alternate tires or wheels on the veh i­
cle that prevent the TPMS from funct io ni ng
properly. Always check the TPMS malfunct ion
tellta le afte r replacing one or more t ires or
wheels on your veh icle to ensure that the re­
p lacement or a lternate tires and wheels allow
the TPMS to continue to function properly.
Tire pressure indicator appears
Applies to vehicles: with tire pressure monitoring system
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too
low or if there is a system malfunction.
F ig. 1 47 Disp lay : under infla tion warn ing
Using the ABS sensors, the tire pressure moni ­
toring system compares the t ire tread circum­
fe rence and vibration characteristics of the in­
d iv idual tires . If the pressure decreases in one
or mo re tires, th is is indicated in the instru­
ment clus ter with a warning symbol
RE and a
message
'* fig. 147. The dr iver message in the
d isp lay goes out after 5 seconds. The driver
message can be d isplayed again by pressing
the
! CHECK I button @¢ page 10, fig . 3 . If on ­
ly one tire is affected, the display will indicate
its pos ition.
The ti re pressure monito ring m ust be reset in
the menu display each time the pressures are
ad justed (e.g. when switching between parti-
Tire s an d wheel s 215
al and fu ll load pressure) or after changing o r
replacing a tire on your vehicle '*
page 216.
The TPMS indicator on ly mon itors the t ire
pressure that you have previously stored . You
can f ind the recommended tire pressures for
your vehicle on the label on the driver's door
pillar ¢
page 200.
Tire tread circumference and vibration charac­
teristics can change and cause a tire pressure
warning if:
- the t ire press ure in one or more tires is too
low,
- the tire has structural damage,
- the t ire press ure was changed, wheels rotat -
ed or rep laced but the TPMS was not reset
¢ page 216.
Warning symbo ls
RE L oss of pressure in a t least one tire ¢ ,&..
Check the tire or tires and rep lace or repa ir if
necessary . The indicator light
RE in the inst ru­
ment cluster a lso i lluminates
¢ page 13 .
Check/correct the press ures of all four tires
and reset TPMS in the menu display .
Iii;~, (T ire Pressure Monitoring System) Ti re
pre ssure! System malfun ction .
Ifllilff' ap­
pears after switching the ignition on or whi le
driv ing and the indicator light
RE in the in­
strument cluster blinks for approx imately one
minute and then stays on, there is a system
malfunction .
Attempt to store the correct tire pressure '*
page 216. If the indicator light does not
turn off or if it turns on shortly thereafter, im ­
med iate ly dr ive your vehicle to a n author ized
Audi dealer or author ized repair fac ility to
have the malfunct io n cor rected.
.8, WARNING
-
- If the tire pressure ind ic a tor ap pears in
the ins trumen t cluster display, one or
more of your tires is significant ly under­
inflated . Reduce yo ur speed immediately
and avoid any hard steer ing or braking
maneuvers. Stop as soon as possible and
check the tires and their pressures.
~
•
•

216 Tires and wheels
Inflate the tire pressure to the proper
pressure as indicated on the vehicle's tire
pressure label¢
page 200. Driving on a
significantly under-inflated tire causes
the tire to overheat and can lead to tire
failure. Under-inflation also is likely to
impair the vehicle's handling and stop­
ping ability .
- The driver is responsible for maintaining
the correct tire pressures. You must
check the tire pressures regularly.
- Under certain conditions (such as a spor­
ty driving style, winter conditions or un­
paved roads), the pressure monitor ind i­
cator may be delayed.
- Ask your authorized Audi dealer if run­
flat tires may be used on your vehicle .
Your vehicle registration becomes invalid
if you use these tires when not permit­
ted. Damage to your veh icle or accidents
could also result.
- If you switch between standard and run­
flat tires, an authorized Audi dealer or
qualified workshop must reprogram the
control module .
@ Tips
-The tire pressure monitoring system
stops working when there is an ESC/ABS
malfunction.
- Using snow chains may result in a system
malfunction .
- The tire pressure monitoring system on
your Audi was developed using t ires with
the "AO" or "RO" identification on the
tire sidewall ¢
page 207. We recom­
mend using these tir es.
Reset tire pressure monitoring system
(Stepl)
Applies to veh icles: w ith tire pressure monitoring system
If the tire pressure is adjusted, wheels are ro­
tated or changed, the TPMS must be reset in
the menu display.
----- ®
Fig. 148 Wipe r lever: Contro ls fo r the menu d isplay
Fig. 149 Disp lay: S ta rt m enu
I Rese t I button @ and rocker switch @
¢
fig. 148 functions:
To open the menu
" Press the I Reset ! button @ unt il the menu
disp lay
~fig. 149 appears
Selections and settings
" Press the rocker switch @ to reach a menu
disp lay. The switch is operated the same as
the display (up/down) .
Entering and confirming
" Press the I Reset I button @.
Returning to the Start menu
" Press the I Rese t I button longer than 2 sec­
onds to return from any menu level to the
Start menu.

@ Tips
-Before resetting the TPMS, the current
pressures of
all four tires must corre­
spond t o the specified va lues. Adjust the
tire pressu re and reset the pressure in
the tire pressure mon itor ing system ac­
cord ing to the load yo u are carry ing
c::> page200.
- Do not store the tire pressure if there are
snow cha ins on the tire .
Reset tire pressure monitoring system
(Step2)
A pplies to vehicles: with t ire pressure monitoring syste m
Fig. 150 D isplay: Tire pressure
Fig. 151 D isp lay: Tir e pressure
I Reset ! button @ and rocker sw itch @
c::> page 216, fig. 148 functions:
Storing tire pressure s
.,. Turn on the ignition.
.,. Se lect the menu :
> Adjusting* > Tire pres-
sure
> Store .
Entering and confirming
.,. Se lect the menu: Store now
.,. Press the
!Reset I button @.
.,. Se lect the menu: Confim
.,. Press the
!Reset I button @. Tires and wheels 21
7
Returning to the Start menu
.,. Press t he I Reset l butto n longer tha n 2 sec­
onds to re turn from any menu level to the
Start men u.
(D Tips
-Before rese tt ing the TPMS, the c urrent
pressures o f
all four tires must corre­
spond to t he spec ified values . Adj ust t he
t ir e pr essure and reset the pressure in
the tire pressu re monitoring system ac­
co rding to the load you are ca rrying
c::> page 200.
- Do not store the tire pressure if there are
snow chains on the tire.
Run-flat tires
Introduction
Applies to vehicles: wit h Run-fla t tires
Run-flat tires help keep you moving if a tire
goes flat.
Re inforced sidewalls give the t ires r un-flat ca­
pabili ty if tire pressure is lost .
We recommend that run-flat tires o nly be
mounted on vehicles that were orig inally
equipped with these special t ires at the facto­
ry an d have a Tire Pressu re Monitoring Sys­
tem .
Run-flat tir es can be identifi ed by th e letters
"RSC" on the tire sidewall.
If you do change the tires on your veh icle from
no rma l to run-flat tires, you must buy the
special rims required fo r run-flat tires, and the
T ire Pressu re M on itor ing System must be re­
programmed by an authorized Aud i d ealer o r
othe r qualified wo rkshop .
What do run -flat tires do?
These special tir es have run-flat capab ilities
that help keep you moving if a tire loses pres­
s ur e and goes flat. Under favorab le condi tions
t ir es can be dr iven
at least 30 miles (SO km) ,
but you mus t not drive fa ster than SO mph
( 80 km/h)
c::> page 218, Driving with run-fla t
tires .
Ill-

218 Tires and wheels
When it is not possible to continue
driving , even with run-flat tires?
-If the E lectronic Stabilization Control (ESC)
is not working or keeps coming on.
- If the
Tire Pr essure Monitoring System does
not work .
- If the tire has been severely damaged, in a
crash , for example. The tread can separate
from a damaged tire as the wheel turns, and
hit parts of the vehicle, such as the fuel tank
filler neck , fuel lines or brake lines.
- Do not continue driving if severe vibration occurs or if the tire starts to smoke because
the tire is running hot.
- Do not continue driving if damage to the
tire, such as cracks in the sidewall, appears.
A WARNING
Improper use of run-flat tires can cause
vehicle damage that can lead to loss of ve­
hicle control, a crash and serious personal
lnJUry.
- Run-flat tires can only be used with spe­
cial rims.
- Run-flat tires must always be mon itored
with a properly programmed Tire Pre­
ssu re Monit oring Sys tem.
- Always inspect a tire that has lost air to
make sure it is safe to drive with the tir e
in the run-flat mode.
- Never drive with run-flat tires that have
been damaged in a collision.
- Never drive with run-flat tires if heat
build-up causes the tire to give off
smoke.
- Never drive with run-flat tires if the vehi­
cle shakes or vibrates severely.
- Never drive with a run-flat tire that de­
velops sidewall cracks or other damage
wh ile in use .
-If you switch between standard and run­
flat tires, an authorized Audi dealer or
qualified workshop must reprogram the
control module.
(D Note
Run-flat tires have specia l characteristics
and requirements, that are very different
from conventional tires. Run-flat tires re­
quire special rims for run-flat use and can­
not be used on conventional wheel rims.
(D Tips
- If you are not able to cont inue driv ing
w ith run-flat tires, please seek professio­
nal assistance.
- Please contact your authorized Audi
dealer or Audi of America, Inc. if you
have questions about tires and rims .
Driving with run-flat tires
Applies to vehicles: wit h Run -flat tires
Handling characteristics change when tire
pressure is low .
Driving on tires with low tire pressure changes
the way a veh icle handles, particularly when
cornering and braking. The handling charac­
teristics of run-flat tires do not seem to
change a lot even when driving on low pres­
sure or in the run-flat mode . Nevertheless you
must still take spec ia l precautions when oper­
at ing a vehicle on run-flat tires when tire pres­
sure is low o r the tire(s) is flat:
.,. Th e Electronic Stabilization Control (ESC)
must be switched on.
.,. Never drive faster than SO mph (80 km/h)
q &_ .
.,. Plan ahead when driving and anticipate
what you will have to do considering traffic
and road conditions up ahead .
.,. Accelerate carefully.
.,. Avo id unnecessary and sudden steering and
brak ing maneuvers .
.,. Reduce your speed in plenty of time before
intersections, curves and other places where
you may have to react qu ickly.
Please see:
qpage 218, When it is not possi­
ble to continue driving, even with run-flat
tires?

Handling characteristics change when
driving with low air pressure or with flat
tires even with special run-flat tires
A low pressure or flat front tire affects vehicle
handling characteristics by pu lling the vehicle
slightly to the side where the tire is mounted
and reduces braking performance .
A low pressure or flat
rear tire also affects
driving character istics by pulling to the side
where the tire is mounted and also reduces
brak ing performance. The effect on vehicle
handling is most not iceable when driving
around curves.
A WARNING
Changed vehicle handling character istics
when driving in the run -f lat mode can
cause loss of vehicle contro l, a crash and
serious personal injury.
- Driving on special run-flat tires in the
run-f lat mode wi ll change vehicle han­
dling characteristics during braking,
when cornering and under heavy acceler­
ation.
- Never drive faster than the maximum
rated speed of 50 mph (80 km/h) when
dr iv ing in the run -flat mode.
- Always adjust vehicle speed to traffic,
road and weather cond itions and drive
slower than the max imum rated speed if
necessary weather and road conditions
are taken into account.
- Always obey speed limits and other traf­
fic laws.
Q) Note
We always recommend driving w ith even
more care when using these special t ires in
the run-flat mode . Always avo id sudden
maneuvers.
Tires and wheels 219
Replacing run-flat tires and rims
App lies to veh icles : w it h Run -flat t ires
Your vehicle was especially designed to use
special run-flat tires.
You may use and combine only approved run­
flat tires and special matching rims that have
been designed for run-flat tires . Mounting
special run-flat tires on standard wheels will not work and w ill not prov ide the advantages
fo the ru n-falt feature . Never use spec ial run­
flat tires on standa rd wheel rims.
After dr iving with a tire i n the run-flat mode,
always have the vehicle and affected tire(s)
and rim(s) inspected by a n authorized Audi
dealer. Tires that have been driven in the run­
f lat mode must be rep laced .
A WARNING
-Use of damaged run-flat tires and rims can
cause vehicle damage that can lead to loss
of vehicle control, a crash and serious per­
sonal injury.
- Always have the vehicle and affected
tire(s) and r im(s) inspected by an author­
ized Audi dealer after driving a tire in the
run-flat mode .
- Tires that have been dr iven in the run­
flat mode must be replaced.
•
•

220 What do I do now?
What do I do now?
Vehicle tool kit
The tools ore stored underneath the floor
panel in the luggage comportment.
Fig. 152 Luggage compartment: vehicle tool kit
• Swing the luggage compartment floor up-
wards.
• Remove the veh icle tool kit .
The on board tool kit includes:
- Hook for removing wheel covers*
- Plastic clip to
remove wheel bolt covers*
-Wheel bolt wrench
- Alignment pin for changing wheels
- Screwdr iver w ith reversible blade
- Replacement bit (reversible Torx b it for
changing lamps)
- Open ended wrench 10 x 13
- Towing eye
- Jack *
Some of the on board items listed above are provided on certain models on ly or are opt ion­
al extras.
Before returning the jack* to its place, retract
the jack arm fully.
_& WARNING
Improper use of the vehicle jack can cause
serious personal injuries.
- Never use the screw driver hex head to
tighten wheel bolts, since the bolts can­ not attain the necessary tightening tor­
que if you use the hex head, potentially causing an accident. -
The factory-supplied jack is intended on­
ly for your vehicle model. Under no cir­
cumstances should it be used to
lift
heavy veh icles or other loads; you risk in­
juring yourself .
- Never start the engine when the vehicle
is raised, which could cause an accident.
- Support the vehicle securely with appro­
priate stands if work is to be performed
underneath the vehicle; otherwise, there is a potentia l risk for injury.
- Never use the jack supplied with your
Aud i on another vehicle, part icularly on a
heav ier one . T he jack is only s uitable for
use on the vehicle it came with.
Tire repair
General and safety pointers
Applies to vehicles: wit h Tire Mobility Sys tem
Tire repair is intended only for temporary,
short-term use .
Fig. 153 Tire damage for whic h the Tir e Mob ility Sys­
tem is not suited
Your vehicle is equipped with a tire repa ir kit,
the
Tire Mobility System (TMS).
In the event of a tire failure, the TMS is in the
luggage compartment under the floor.
It con­
s ists of the tire sealant and an electric air
pump .
Using
TMS , tir e damage caused by foreign
bodies up to about
0.16 inch (4 mm) in diam­
eter can be sealed reliably.
The foreign object can stay in the tire .

The tire sea lant mu st not be us ed :
- for c uts or punctures in the tire which are
l arger than 0.16 inch (4 mm)
q fig. 153 (D
- for damage to the rim@
- if you have been driving with very low ti re
pressures or tires with no air @
Using the
TM S is described in the section
q page 221, Preliminary steps .
TMS can be used at temperatures down to
-4 °F ( -20 °() .
A WARNING
Take the following precautions after re­
pairing the tire:
- Do not drive faster than
50 mph (80 km/
h)!
- Avoid full-throttle accelerat ion, heavy
braking and fast cornering .
- The veh icle's road behavior can be affect­
ed .
- Tires sealed with
TMS are intended only
for
temporar y, short -term use.
-After using the t ire sealant the tire pres­
sure monitoring system may no longer
work prope rly. Drive carefully to the next
professional repair fac il ity.
- TMS must NOT be used,
- for cuts or punctures in the tire which are larger t han 0.16 inch (4 mm)
- for damage to the rim
- if you have been driv ing with very low
tire pressures or t ires with no air
- Seek profess ional assistance if it is not
poss ible to repair the tire with the tire
sealant.
A WARNING
T he tire sealant must not come into con­
tact w ith skin, eyes or cloth ing.
- If you get any tire sealant in your eyes or
come into contact with it, r inse the af­
fec ted area t ho roughly with cle an wate r.
Find a physician immediately!
- Change any clot hing contaminated with
t ire sea lant immed iate ly.
- Do not inhale the vapo r!
-
What do I d o now ? 221
-If you have swallowed tire sealant, rinse
your mouth thoro ughly right away and
drink plenty of water.
- Do not induce vom it ing! Find a physi­
c ian immediately!
- I f you have allergic react ions, find a
phys ician immediately.
- Keep the tire sealant away from children .
(D Note
Do not use commercially available tire
sealants . The e lectr ica l components of the
tire pressu re monitoring system will no
l onge r work properly .
@ For the sake of the env ironment
Used sealant bottles can be dropped off at
a recycling facility.
@ Tips
- If sea lant has run out, allow it to dry.
Then you can peel it off.
- Have the t ire sea lant replaced every 4
years at a dealership.
Preliminary steps
Applies to vehicles: with Tire Mobility System
Some preliminary steps are necessary for tire
repair.
Fig. 154 Lu ggage compartment: Tire Mob ility System
.,.. If you have a flat tire, park the vehicle as far
as poss ib le from moving t raff ic.
.,.. App ly the
parking brake firmly .
.,.. Shift into
1st gear on veh icles with man ual
transmission, or move the
s electo r le ver to
the P po sit io n
on vehicles with automatic
transmiss ion.

222 What do I do now?
• Check whether a repair using the Tire Mobi­
li ty System is possible ¢
page 2 20, General
and safety pointers.
• Have all passengers leave the vehicle and
stay away from the danger zone ¢
&,..
• Take the sealant bottle and the electric air
pump from the luggage compartment un­
der the floor ¢
fig. 154 .
• Remove the "max. SO mph" (80 km/h)
sticker from the sealant bottle and affix it to
the instr ument cluster in the driver's view.
~ WARNING
- Turn the hazard flashers on and set up
the warning triang le if you have a flat
t ire in moving traffic. In this way you pro­
tect you rs elf and other road users.
- Make sure that all passengers are in a
safe place, out of the danger zone (for
example, behind a guard rail).
(D Note
Particular care is necessary if you are mak­
ing a tire repair on a steep incline.
(D Tips
Obey all laws.
Making a tire repair
App lies to vehicles: with Tire Mobility System
Tire repair consists of the following sections.
Fig. 155 Parts of the Tire Mobility System
-
1) The ele ctr ic a ir pump s hould never ru n for lo nger than
6 min utes.
Fig. 156 Connector for the Tire Mob ility System
Assembling Tire Mobility System
• Open the lid@ of the electric air pump
¢fig. 155.
• Pull the plug@and the pressure hose ®
w ith the gauge out of the housing.
• Screw the pressure hose ® of the electric
air pump onto the flange @ of the sealant
bott le
(D .
• Push the sea lant bott le with the flange
down into th e recess @ on the lid of the
electric air pump.
• Remove the dust cap from the valve of the
defective tire .
• Screw the hose (@onto the valve
(J)
¢ fig. 156.
• Insert the plug @¢fig . 155 into the socket
for the cigarette lighter.
• Switch on the ignition .
Inflating tire
• Move the switch @¢ fig. 156 on the elec­
tric air pump
l) to position I. After 5 mi­
nutes, tire pressure must have reached at
least 1.8 bar.
• Switch the e lectric air pump off -sw itch in
position
0. If the required tire pressure of at
least 1.8 bar has not been reached, follow
the instructions in the section
Re-inflating
tire.
Re-inflating tire
• Remove the hose from the valve and pull
the plug out of the socket.