2013 AUDI A5 CABRIOLET Owners Manual

Loading the vehicle onto a flat bed truck
Fig. 206 Ve hicle on fla t bed tr uck
Front hook up
.. Align the ve hicle wi th the centerline of the
car car rier ramp.
.. Attach the winch hook to the front towline
eye previously installed .
Rear hook up
.. Align the vehicle with the centerline of the
car carri er ramp.
.. Attach the winch hook to the rear towline
eye prev iously ins talled .
(D} Tips
Check carefully to make sure the hook- up
is secure before moving the car up the flat­
bed truck ramp .
Lifting vehicle
Lifting with workshop hoist and with
floor jack
The vehicle may only be li~ed at the lifting
points illustrated .
Fig. 2 07 Fro nt l ift ing po int
Emergenc y situ ation s 263
Fig. 208 Rea r liftin g po int
.,. Read and heed WARNING c::> .&, .
.,. Locate lifting points c::> fig . 207 and
c:>fig. 208 .
.,. Adjust lifting arms of workshop hoist o r
floor jack to ma tch veh icle lifting points.
.. Insert a rubbe r pad between the floo r jack/
workshop hoist and the lift ing points.
If y ou mu st lift your veh icle with a fl oor jack
to w ork und erneath , be sure the vehicle is
safel y supported on stand s intended for thi s
purpo se .
Front lifting point
T he lifti ng po int i s loca ted o n the floo r pan re­
i nforcemen t abo ut a t the same level a s the
jack mounting point
c:> fig. 207. Do not lift
the vehicle at the vertic al sill reinforcement.
Rear lifting point
T he lifting point is located o n the vert ica l rein­
f o rcement of the lower s ill for the on board
jack
c::> fig. 208 .
Lifting with vehicle jack
Refer to ¢page 252 .
A WARNING
-To reduce the risk of ser ious injury and
veh icle damage.
- Always lift the vehicle only at the spe­
cia l workshop hoist and floor jack lift
points illustrated
c:> fig. 207 and
c:> fig. 208.
- Fail ure to lift the veh icle at these
-
po ints could cause the vehicle to tilt or ..,.

264 Emergency situations
fall from a lift if there is a change in ve­
hicle weight distribution and balance.
This might happen, for example, when
heavy components such as the engine
block or transmission are removed .
- When removing heavy components like
these, anchor vehicle to hoist or add cor­
responding weights to maintain the cen­
ter of gravity. Otherwise, the vehicle
might tilt or slip off the hoist, causing
serious personal injury.
(D Note
- Be aware of the following points before
lifting the vehicle:
-The vehicle should never be lifted or
jacked up from underneath the engine
oil pan, the transmission housing, the
front or rear axle or the body side
members. This could lead to serious
damage.
- To avoid damage to the underbody or
chassis frame, a rubber pad must be
inserted between the floor jack and
the lift points.
- Before driving over a workshop hoist,
check that the vehicle weight does not
exceed the permissible lifting capacity
of the hoist.
- Before driving over a workshop hoist,
ensure that there is sufficient clear­
ance between the hoist and low parts
of the vehicle.

General information Explanation of
technical data
Som e of t he technical data listed in this man­
ual requires further explanation.
The technical data for your vehicle is listed in
the charts starting on
c:> page 267. This sec­
tion provides general information, notes and
r estr ictions wh ich app ly to this data.
Vehicle identification
The key data is given on the vehicle identifi ca­
tion number ( VIN) plate and the vehicle data
sti cker .
Fig. 20 9 Vehicle Identificat ion Num ber (VlN) p la te: lo ­
cation o n drive r"s side dash pa nel
Fi g. 2 10 The ve hicle identificat ion label -in side the
l u ggage compartme nt
The Vehicle Identification Number (VlN)
is located on the d river's side so tha t it is v is i­
b le from the outside throug h the windshield
c:> fig . 209. You can also d isplay the Vehicle
Identification N umber of your vehicle in the
radio or in the MM!*. Select: ICAR!function
button
> Vehicle ID number (VIN) or select :
I CA R
I function butto n > Car systems* control
button
> Servicing & checks > VIN number .
General inform ation 265
The vehicle identification label
is lo cated in the l uggage comp artment near
the battery.
T he label
~fig. 210 shows th e fo llow ing vehi­
cl e d ata:
(D Product ion cont ro l No.
@ Vehicle identific ation No.
@ Type code number
© Type designat ion/e ngine o utput in K ilo-
wat ts
® Engine and transm ission code letter
® Pa int No./lnterior
0 Option al eq uipmen t No.'s
Vehicle data 2 to 7 are a lso fo und in your War­
ranty
& Mai nte nance bookle t.
The safety compliance sticker
is your assurance that your new vehicle com­
plies wi th a ll applicable Fede ral Motor Vehicle
Safety S tandards which were in effect at the
tim e the ve hicle was manufactur ed. You ca n
find this sticke r o n the left doo r jamb.
It
sh ows the m onth and ye ar of pro duction and
t h e ve hicl e ident ifi cat io n number of yo ur vehi ­
cle (perfora tion) as well as the G ross Vehicle
Weight Rating (GVW R) and the Gross Axle
Weight Rating (GAWR) .
The high voltage warning label
is lo cated on the l ock ca rrie r.
The spark ignition system complies with
the Canadian standard ICES-002.
Weights
Gross Vehicle Weight Rating
T he Gro ss Vehicle Weigh t Rat ing (GVWR), and
the Gross Axle We igh t Ra tin g (GAWR) for
fron t and rear are listed on a sticker on the
l eft door jamb .
T he Gro ss Vehicle Weigh t Rat ing incl udes the
weig ht o f the bas ic vehicle plus f ull fuel t ank,
oi l and coo lant, p lus maximum load, which in­
cludes passen ger we ight (150 lbs./68 kg per ..,.

26 6 G enera l inform ation
designated seating position) and luggage
w eight ¢.&, .
Gross Axle W eight Rating
The Gross Axle Weight Rating is the maximum
l oad that can be applied at each axle of the
vehicle ¢Lr!, .
Vehicle capacit y weight
The vehicle capac ity we ight (max . load) is list­
ed on the driver's side 8-p illar.
A WARNING
- T he actual Gross Axle Weight Rat ing at
the front and rear axles sho uld not ex­
ceed the permissible weights, and their
combination must not exceed the Gross
Vehicle Weight Rating.
- Exceeding permissib le weight ratings can
result in vehicle damage, accidents and
persona l injury .
(D Note
-The vehicle capacity weight figures apply
when the load is distributed evenly in the
vehicle (passengers and luggage) . When
transporting a heavy load in the luggage
compartment, carry the load as near to
the rear axle as possible so that the vehi­
cle's handling is not impa ired.
- Do not exceed the maximum permissible
axle loads or the maximum gross vehicle
weight . Always remember that the vehi ­
cle's handling will be affected by the ex­
tra load . Therefore, adjust your speed ac­
cord ingly.
- Always observe loca l regu lations .
Dimensions
.
The specifications refer to the basic model.
Differences may occur depending on the mod­
e l type and options ordered, for example, tire
si zes.
Note
When driving up steep ramps, on rough
roads , ove r curbs, etc. it is important to re -member that some pa
rts of your vehicle,
such as spoi lers or exhaust system compo­
nents, may be close to the ground. Be
careful not to damage them .

Data
211 hp, 2.0 liter 4-cyl. engine
Engine data
211 @4300-6000
Maximum output SAE net
Maximum torque SAE net
No. of cylinders
Displacement hp@rpm
lb-ft@ rpm
-·--
Stroke
Bore
Compression ratio CID (cm
3
)
in (mm)
in (mm)
__ .. ,
258@ 1500-4200
4
121 (1984)
3 .65 (92.8)
3.25 (82 .5)
9 .6: 1
Data
Fuel Premium unleaded (91 AKI) Recommended for maxi­
mum engine performance. Further details¢ page 207,
Gasoline
Bio-Ethanol (E85) Vehicles with flexible fuel engines may
be operated with bio-ethanol fuels (E85) or with premium
unleaded gasoline (91
AKI) . Further details¢ page 208,
E thanol fuel (Bio-ethanol).
Dimensions (approx .)
Length (with licence plate bracket) in (mm)
Width (with outside mirrors folded) in (mm) He ight (unloaded) in (mm)
T urning circle diameter (curb to curb) ft (m)
Capacities (approx.)
Fuel tank
- Total capacity
- Reserve (of total capacity)
--.. ,
--.. ,
Windshield and headlight* washer fluid container Engine oil
with filter change 182
.1 (4626)
73.0 ( 1854)
54.4 (1383)
37 . 4 (1 1.4)
gal (liters)
gal (liters)
quarts (liters)
quarts (liters) 1.8-2.4
(7-9)
4 .9 (4 .6)
267
•
•

268 Data
333 hp, 3.0 liter 6-cyl. engine
Engine data
Maximum output SAE net
Maximum torque SAE net
N o. of cylinders
Displacement
Strok e
Bore
C ompressio n ratio
Fuel
Dimensions (approx .)
Leng th (wit h licence pl ate bra ck et)
Width (with outside mirrors folded) He igh t (unloaded) in (mm)
in (mm)
in (mm)
T urning circle diamet er (curb to curb) ft (m)
Capacities (appro x.)
Fuel tank
- Total capacity
- Reserve (o f to tal capacity) h
p@rpm
L b-ft@ rpm
C ID (cm
3
)
in (mm)
i n (mm)
333 @ 5500-6500
325
@ 2900-5300
6
182.8 (2995)
3.50 (89)
3 .33 (84 .5)
1 0.3 : 1
Premium unleaded (91 AKI) Recomme nded for
m aximum engine performance . Further details
¢ pag e 207, Gasoline
18 2 . 7 ( 464 0)
73.0 (1854)
5 4. 3 ( 138 0)
37 .4 (11.4)
gal (liters) 1 6 .1 (61.0)
g al (li ters) 1.8-2 .4
(7 -9)
Windshield and headlight* washer fluid container quarts (li ters) 4.8 (4 .5)
Engine oil with filter change qu
arts ( lite rs) 7. 2 (6 .8)

Consumer Information
Warranty coverages
Your Audi is covered by the following war­
ranties :
- New Vehicle Limited Warranty
- Limited Warranty Against Corrosion Perfo-
ration
- Emissions Control System Warranty
- Emissions Performance Warranty
- California Emissions Con trol Warranty (USA
vehicles only)
- California Emissions Performance Warranty
(USA vehicles only)
Detailed information regarding your warran ­
ties can be found in your
Warranty & Mainte­
nance booklet .
Operating your vehicle
outside the U.S.A. or
Canada
Government regulations in the United States
and Canada require that automobiles meet
specific emission regulations and safety
standards. Therefore, veh icles built for the
U.S.A. and Canada differ from vehicles sold in
other countries .
If you p lan to take your vehicle outside the
continental limits of the United States or Can­
ada, there is the possibility that:
- unleaded fuels for vehicles with cata lytic
converter may not be available;
- fuel may have a considerably lower octane
rating . Improper fuel may cause engine
damage ;
- service may be inadequate due to lack of
proper service facilities, tools or testing
equipment ;
- replacement parts may not be readily availa­
ble.
- Navigation systems for vehicles built for the
U.S.A. and Canada will not necessari ly work
in Europe, and may not work in other coun­
tries outside of North America.
Consumer Information 269
@ Note
Audi cannot be responsible for mechanical
damage that could result from inadequate
fuel, service or parts availability.
Audi Service Repair Manuals and Literature
Audi Offic ial Factory Service Manuals and Lit ­
erature are published as soon as possible after
model introduction. Service manuals and lit­
erature are available to order from the Audi
T echnical Literature Ordering Center at:
www.audi.techliterature.com
Maintenance
' General
Your vehicle has been designed to help keep
maintenance requirements to a minimum.
However, a certain amount of regular mainte­
nance is still necessary to assure your vehicle's
safety, economy and reliability . For detailed
vehicle maintenance consult your Warranty
&
Maintenance booklet.
Under difficult operating conditions , for ex­
ample at extremely low outside temperatures ,
in very dusty regions, when towing a tra iler
very frequently, etc., some serv ice work
shou ld be performed between the intervals
specified. This applies particularly to:
- oil changes, and
- cleaning or replacing the air filter .
® For the sake of the environment
By regularly maintaining your vehicle, you
help make sure that emission standards
are maintained, thus min imizi ng adverse
effects on the environment .
Important considerations for you and
your vehicle
The increasing use of electronics , sophisticat­
ed fuel injection and emission control sys-
tems, and the genera lly increasing technica l ..,_
•
•

2 70 Con sum er Inf ormation
comp lexity of today's automobi les, have
steadi ly reduced the scope of maintenance
and repairs which can be carried out by vehicle
owners.
Also, s afety an d e nvir onm ent al con­
cerns place very strict limits on the nature of repairs and adjustments to engine and trans ­
miss ion pa rts which an owner can perform .
Maintenance, adjustments and repa irs usua lly
require special tools, testing devices and oth­
er equipment avai lab le to specially trained
workshop personnel in order to assure proper
performance, reliab ility and safety of the vehi­
cle and its many systems .
Improper ma intenance, adjustments and re ­
pa irs can impair the operation and reliab ility
of your vehicle and even void your vehicle war­ ranty. Therefo re , proof of servici ng in accord­
ance w it h the ma intenance sched ule may be a
condition for upholding a possible warranty
claim made within the warran ty period.
Above all, operational safety can be adve rsely
affected, c reating unnecessary risks for you
and your passengers.
If in doubt about any serv icing, have it done
by your author ized Audi dealer or any other
p roperly equipped and qualified workshop .
We strong ly urge you to give your authorized
Audi dealer the opportunity to perform all
schedu led maintenance and necessary repairs .
Your dea ler has the facilities, or iginal parts
and tra ined spec ialists to keep your vehicle
running properly .
Performing lim it e d m aint en anc e y ourself
The fo llowing pages describe a limited num­
ber of procedures which can be performed on
you r vehicle with ordinary too ls, shou ld the
need arise and trained personnel be unavaila­
ble. Before performing any of these proce­
dures, always thoroughly read all of the app li­
cable text and ca refully follow the instruc­
tions given. Always rigorously obse rve the
WARNINGS p rovided .
Before you ch eck anything in th e engin e
compartme nt, alway s read an d heed all WARNINGS
¢ & a
nd ¢ & in Working in the
engine comportment on page 212 .
A WARNING
--Serious personal in jury may occur as a re-
sult of improperly performed mainte­ nance, adjustments or repa irs.
- Always be extremely careful when work­
ing on the vehicle. Always follow com­
monly accepted safety pract ices and gen­
eral common sense. Never r isk personal
in jur y.
- Do not attempt any of the maintenance,
checks or repairs descr ibed o n the fol­
lowing pages if you are not fu lly fam iliar
with these or other procedures with re­ spect to the ve hicl e, or are uncerta in how
to proceed .
- Do not do any work withou t the proper
too ls and equipment . Have the necessary
work done by your authorized A udi deal ­
er or anothe r properly equipped and
qualified workshop.
- The engine compar tment o f any motor
vehicle is a potentially hazardous area. Never reach into the area around or
touch the rad iator fan. It is temperature
control led and can sw itch on suddenly -
even when the engine is off and the igni­
tion key has been removed. The rad iator
fan switches on automatically when the coo lant reaches a certai n tempera ture
and will cont inue to run until the coo lant
temperature drops .
- Always remove the ign ition key befo re
a nyone gets under the veh icle.
- Always suppor t your veh icle with safety
s tands if it is necessary to work under­
neath the vehicle. The jack s upplied with
the vehicle is not adequate for this pur ­
pose and co uld co llapse causing serio us
personal injury.
- If you must work unde rneath the vehicle
with the wheels on the ground, a lways
make sure the vehicle is on leve l ground,
that the wheels are always secure ly
blocked and that the engine cannot be
started.