2012 Lancia Flavia Owner handbook (in English)

CavityCartridge Fuse Mini Fuse Description
31 —10 Amp RedHeadlamp Washer (for versions/markets,
where provided)
32 30 Amp Pink —Auto Shutdown (ASD) Relay 1
33 —10 Amp RedSwitch Bank/Diagnostic Link Connector/
Powertrain Control Module (PCM)
34 30 Amp Pink —Anti-Lock Brakes (ABS) Module (for
versions/markets, where provided)/
Electronic Stability Control (ESC) Module
(for versions/markets, where provided)
35 40 Amp Green —Anti-Lock Brakes (ABS) Module (for
versions/markets, where provided)/
Electronic Stability Control (ESC) Module
(for versions/markets, where provided)
36 30 Amp Pink —Passenger Door Module (PDM)/Driver Door
Module (DDM)
37 —25 Amp Natural Power Top Module (for versions/markets,
where provided)
CAUTION!
 When installing the Integrated
Power Module cover, it is impor-
tant to ensure the cover is properly
positioned and fully latched. Fail-
ure to do so may allow water to get
into the Integrated Power Module,
and possibly result in an electrical
system failure.
(Continued)
CAUTION!(Continued)
 When replacing a blown fuse, it is
important to use only a fuse hav-
ing the correct amperage rating.
The use of a fuse with a rating
other than indicated may result in
a dangerous electrical system
overload. If a properly rated fuse
continues to blow, it indicates a
problem in the circuit that must
be corrected.
202

VEHICLE STORAGE
If you will not be using your vehicle
for more than 21 days, you may want
to take steps to preserve your battery.
 Disengage the mini-fuse in thePower Distribution Center labeled
IOD (Ignition Off-Draw).
 Or disconnect the negative cable from the battery. Refer to “Prepa-
ration for Jump Start” in “Jump-
Starting” to identify the location of
the negative post.
 Anytime you store your vehicle, or keep it out of service (i.e., vacation)
for two weeks or more, run the air
conditioning system at idle for
about five minutes in the fresh air
and high blower setting. This will
ensure adequate system lubrication
to minimize the possibility of com-
pressor damage when the system is
started again.
REPLACEMENT BULBS
All the inside bulbs are brass or glass
wedge base. Aluminum base bulbs are
not approved and should not be used
for replacement. LIGHT BULBS – Interior Bulb No.
Front Courtesy/Reading
Lamp . . . . . . . . . . . . . . 578/W5W
Center Courtesy/Reading
Lamp . . . . . . . . . . . . . . 578/W5W
Glove Box Lamp . . . . . . . . . . . 194
Shift Indicator Lamp . . IKLE14140
Rear Compartment (Trunk)
Lamp . . . . . . . . . . . . . . . . . . . 579
NOTE:
For lighted switches, see your au-
thorized dealer for replacement.
LIGHT BULBS – Exterior Bulb No.
Bi-Halogen Headlamp . . . . . . HIR2
Front Turn Signal Lamp . . 3157NAKFront Park Lamp . . . . . . . . . . LED
(Serviced at Authorized Dealer)
Side Repeater Lamp . . . . . . WY5W
Front Fog Lamp . . . . . . . . . . . H11
Center High Mounted Stop
(CHMSL) Lamp . . . . . . . . . . LED
(Serviced at Authorized Dealer)
Rear Tail/Stop Lamp . . . . . . . LED
(Serviced at Authorized Dealer)
Rear Turn Signal Lamp . . . . W16W
Rear Fog Lamp . . . . . . . . . . . LED
(Serviced at Authorized Dealer)
Backup Lamp . . . . . . . . . . . W16W
License Lamp. . . . . . . . . . . . W5W BULB REPLACEMENT
HEADLAMP
CAUTION!
Where possible, it is advisable to
have bulbs changed at a LANCIA
Dealership. Proper operation and
orientation of the external lights are
essential for driving safety and com-
plying with the law.
1. Raise and prop open the hood. Lo-
cate the connector behind the head-
lamp.
NOTE:
It may be necessary to remove the
air cleaner filter housing and po-
sition the totally integrated power
module aside prior to replacing
the low beam headlamp on the
driver's side of the vehicle.
203

2. Reach into engine compartment
and from behind the lamp assembly
and grasp the connector.
3. Rotate bulb and connector one-
quarter turn and pull outward from
assembly.CAUTION!
Do not touch the new bulb with your
fingers. Oil contamination will se-
verely shorten bulb life.
4. Pull the bulb out of the socket and
replace the bulb. 5. If the bulb comes in contact with
any oily surface, clean the bulb with
rubbing alcohol.
6. Reinsert the bulb and socket as-
sembly and rotate clockwise one-
quarter turn to secure.
FRONT TURN SIGNAL
1. Raise and prop open the hood.
2. Rotate the
bulb's electrical con-
nector one-quarter turn counter-
clockwise and remove it from the
headlamp housing.
3. Remove the bulb from the connec-
tor socket and install the replacement
bulb.
4. Install the bulb and connector as-
sembly into the headlamp housing
and rotate the connector one-quarter
turn clockwise to lock it in place. FRONT FOG LAMP
NOTE:
Access to the lamps through the
lower fascia cutout is limited. We
recommend you access the lamps
by turning the steering wheel to
allow access and remove the inner
fender shield.
1. Rotate the
bulb's electrical con-
nector one-quarter turn counter-
clockwise and remove it from the fog
lamp housing.
2. Remove the bulb from the connec-
tor socket and install the replacement
bulb.
CAUTION!
Do not touch the new bulb with your
fingers. Oil contamination will se-
verely shorten bulb life. If the bulb
comes in contact with an oily sur-
face, clean the bulb with rubbing
alcohol.
3. Install the bulb and connector as-
sembly into the fog lamp housing and
rotate the connector one-quarter turn
clockwise to lock it in place.
204

REAR TURN SIGNAL
LAMPS
1. Open the trunk and gently pull
back the trunk liner behind the tail
lamp (requires removal of a push pin
holding the trunk trim in place near
the tail lamp).
2. Remove the two plastic wing nuts
from the tail lamp housing.
NOTE:
Placing a small flat head screw-
driver or similar tool between the
lamp outboard ball stud and plas-
tic grommet from inside the trunk
can help to disengage the outboard
edge of the tail lamp.
3. Grasp the tail lamp by both the
outboard and inboard sides, and pull
firmly to disengage the tail lamp from
the vehicle.NOTE:
It is normal to hear a loud sound
when the lower tail lamp area un-
snaps from the vehicle mounting
bracket during tail lamp removal.
4. Twist and remove socket from
lamp.
5. Remove bulb from socket and re-
place.
6. Reinstall the tail lamp, fasteners,
and trunk liner.
BACKUP LAMP
1. Remove four push pins from the
bottom of the lower valance (from left
to right: 1st, 3rd, 6th & 8th) and two
push pins from the rear of the bracket.
2. Remove bracket by pulling for-
ward of vehicle.
3. Remove socket from housing with
a counter-clockwise
14turn.
4. Remove bulb from socket by pull-
ing directly out (do not turn/twist)
and install replacement bulb.
5. Insert socket back into the housing
with a clockwise
14turn.
6. Return bracket into position.
7. Snap the six (6) push pins back
into place.
LICENSE PLATE LAMP
1. Using a small screwdriver, press
inward the locking tab on the side of
the lamp assembly and pull down on
the lamp assembly for removal.
2. Remove bulb socket by twisting
out of lamp assembly.
3. Pull bulb from socket, replace, and
reinstall the bulb socket into lamp
assembly.
4. Install lamp assembly to lightbar
ensuring the locking tab is secure.
205

FLUID CAPACITIES
Metric
Fuel (Approximate)
All 64 Liters
Engine Oil with Filter
2.4L Engine 4.4 Liters
Cooling System*
2.4L Engine 7.3 Liters
* Includes heater and coolant recovery bottle filled to MAX level.
FLUIDS, LUBRICANTS, AND GENUINE PARTS
ENGINE
Component Fluids and Lubricants Specs (Genuine Parts)
Engine Coolant* Contact a LANCIA Dealership.
Engine Oil** SAE 5W-20 grade totally synthetic lubricant that meets FIAT Classification
9.55535-CR1, API SN, ILSAC GF-5 (SELENIA K POWER, Contractual Tech-
nical Reference N° F102.F11)
Spark Plugs ZFR5F-11 (Gap 1.1 mm)
Fuel Selection 91 Octane or higher
* Do not top up or mix with fluids
with different specifications.
** In the event of an emergency in
which the original products are not
available, lubricants with at least IL-
SAC GF-5 performance are accept- able. In this case optimum engine per-
formance is not guaranteed and the
lubricants should be replaced with
recommended products as soon as
possible at a LANCIA Dealership.
The use of products with features
lower than ILSAC GF-5 could cause
engine damage not covered by the
warranty.
206

CHASSISComponentFluids and Lubricants Specs (Genuine Parts)
Automatic Transmission Totally synthetic lubricant that meets FIAT Classification 9.55550-AV4 (TU-
TELA TRANSMISSION FORCE4, Contractual Technical Reference N°
F108.F11)
Brake Master Cylinder Synthetic fluid that meets FIAT Classification 9.55597, FMVSS n° 116, DOT 4,
ISO 4925, SAE J-1704 (TUTELA TOP 4, Contractual Technical Reference N°
F001.A93)
Power Steering Reservoir Totally synthetic lubricant that meets FIAT Classification 9.55550-AV4 (TU-
TELA TRANSMISSION FORCE4, Contractual Technical Reference N°
F108.F11)
Windshield/Rear Window Washer
Fluid Mixture of alcohol, water and surfactants that meets FIAT Classification
9.55522, CUNA NC 956-11 (TUTELA PROFESSIONAL SC35, Contractual
Technical Reference N° F201.D02)
207

ARRANGEMENTS FOR DEALING
WITH THE VEHICLE AT THE
END OF ITS LIFE
LANCIA has been committed for
many years to safeguarding the envi-
ronment through the constant im-
provement of its production processes
and manufacturing products that are
increasingly “eco-compatible”.
To give customers the best possible
service in terms of respecting environ-
mental laws and in response to Euro-
pean Directive 2000/53/EC govern-
ing vehicles at the end of their life,
LANCIA is offering its customers the
opportunity of handing over their ve-
hicle* at the end of its life without
incurring any additional costs.The European Directive sets out that
when the vehicle is handed over the
last keeper or owner should not incur
any expenses as a result of it having a
zero or negative market value.
In all European Union countries, until
1st January 2007, only vehicles regis-
tered after 1st July 2002 were col-
lected free of charge, while since 2007
collection has been free of charge irre-
spective of the year of registration as
long as the vehicle contains its basic
components (in particular, the engine
and bodywork) and has no additional
waste.
To hand your vehicle over at the end
of its life without extra cost, go to one
of our Dealerships or LANCIA-
authorized collection and scrapping
centres.These centres have been carefully
chosen to offer high quality service for
the collection, treatment and recy-
cling of unused vehicles with respect
to the environment.
You can find further information on
these collection and scrapping centres
either from a LANCIA or LANCIA
Commercial Vehicle Dealership or by
calling the freephone number 00800
526242 00 or by going on the
LANCIA website.
(*) Vehicle for transporting passen-
gers with a maximum of nine seats
and a total permitted weight of 3.5 t
208

209