Page 17 of 316

Instrument s and warnin g/indic ator ligh ts 15
reduced speed to a qualified workshop. Steer
ing can be more difficult or sensitive than usu
a l. The steering wheel may also be at an ang le
when dr iving stra ight.
_&. WARNING
Have the dynamic steering system mal
function repaired as soon as poss ible by an
authorized Audi dealer or any qualified
workshop -risk of accident!
@ Tips
- If the ,'2:"J indicator light flashes, dynam ic
steering is being re-initialized. The driver
i nformat ion system display shows the
words "Dynamic steering: initialization"
¢ page 34.
- The dynamic steering stability systems
are not available in the event of a system
malfunction.
EPC Electronic power control
This warning/indicator light monitors the
electronic power control.
The ~ warn ing/indicator light (Electronic
Powe r Control) illuminates when you turn o n
the ignition as a function check.
(D Tips
If th is warning/indicator light illuminates
while you are dr iving, then the re is a mal
function in the engine elect ron ics. Have
the malfunction corrected as soon as pos
sible by you r autho rized Aud i dea le r o r
qua lified workshop .
J;. ID Electronic stabilization program
(ESP)
If the Jjj indicator lamp blinks while dr iv ing,
the ESP or ASR (Ant i- Slip Regulation) is active
ly regulating .
If the
D] i ndicator lamp ill uminates, the sys
tem has switched the ESP off. I n this case, you
can switch the ignition off and then on to
switch the ESP on again . The system is func- tion
ing comp lete ly when the indicator lamp
switches off.
If t he I ind icator lamp illum inates, the ESP
was switched off w ith the
I~ O FF I button.
Stabili sation program and ABS fault ! See
owner' s manual
If the Ii] indicator lamp a nd the ti] ABS indi
cator lamp illum inate and the driver message
appears, the ABS or electro nic different ia l lock
is malfunct io ni ng . This a lso inte rrupts the
E S P. The brakes s till function with their nor
mal power, but ABS is not active.
D rive to your author ized A udi dealer immedi
ate ly to have the ma lfunction corrected .
Fo r more information about the ESP
¢ page 204.
tli I !.Jr Safety systems
T he I (USA mode ls)/ . (Canada mode ls) i n
di ca tor light mon itors the safety systems e .g.
airbags, pretens ione rs and illuminates fo r a
f ew seconds each time you switch the ignit ion
on .
If the I (USA models) /. (Canada models)
indica to r ligh t does not go o ut, or if it ill umi
na tes while you are driving, o r if i t starts to
blink, then there is a malfunction somewhe re
in the system. If the light does not i lluminate
when you switch the ign ition on, th is also
means there is a malfunct ion.
_&. WARNING
If you have a ma lfunction in the safety sys
tems, contact your authorized Audi dea ler
immediately . Othe rwise the safety sys
tems may not work properly in an ac ci
d ent.
Page 18 of 316

16 Instruments and warning/indicator lights
(l) Tire pressure monitoring system -
telltale indicator lamp
A ppl ies to vehicles: with tire pressure monit oring sys te m
The warning/indicator light appears in the
event of a significant loss of air pressure.
The ti) warning/ind icator light illuminates for
a few seconds after the ignit ion is turned on
as function check, and then goes out.
If the
(g symbol appears, pressure is too low
in at least one tire.
When the system detects a ma lfunction, the
warning/indicator light will flash for approx i
mately one minute and then remain continu
ously illum inated. Th is sequence will continue
upon subsequent vehicle starts up as long as
the ma lfunction ex ists. Contact your author
ized Audi dealer and have the malfunction
corrected .
For more informat ion
c::> page 2 71 .
¢i 9 Turn signals
The indicator light blinks when you use either
turn signal .
Whenever you use the left B or the right II
turn signal, the indicator light blinks. When
you use the emergency flashers , both indica
tor lights flash .
If one of the turn signal light bulbs burn out,
the turn signal will blink tw ice as fast as nor
mal.
~ Safety belts
This warning/indicator light reminds you to
put on your safety belt.
The . warning/ indicator light illum inates
when the ignition is switched on to remind
the dr iver and (on USA models only) any front
passenger to put on the safety belt. Add ition
a lly, an audible warning tone will a lso sound.
For more Information
c::> page 154, Safety
belt warning light.
o Malfunction Indicator Lamp (MIL)
The Ma lfunction Indicator Lamp (MIL) is part
of the On-Board Diagnostic (OBD II) system.
The
fcj symbol lights up when the ign ition is
turned on and will turn off after the engine
has started and has settled at a constant idle
speed. This indicates that the MIL is work ing
proper ly.
The warning light illuminates when there is a
malfunction in the engine electronic system.
Contact your authorized Audi dea ler and have
the malfunction corrected.
For more information
c::> page 26.
~D High beam
The II warning/indicator light illuminates
when the high beams are on or when you use
the headlight flasher. For more information
about using the high beams, see
c::> poge 52.
CRUISE/ (,)" Cruise control
Them! (USA models)/ . (Canada models)
warning/indicator light illuminates when the
cruise control is activated .
ABS/ (9) Anti-lock brake system (ABS)
This warning/indicator light monitors the ABS
and the electronic differential lock (EDL).
The warn ing/indicator light r4iS (USA mod
els)!Ei] (Canada models) will come on for a
few seconds when the ignition is switched on.
T he light will go out after an automatic check
sequence is completed.
There is a malfunction in the ABS when:
-The warning/indicator light does not i llum i
nate when you switch on the ignition .
- The warning/indicator light does not go out
after a few seconds.
- The warning/indicator light illuminates
while driving.
The brake system will still respond even
without the assistance of the ABS system.
Page 19 of 316

Instruments and warning/indicator lights 17
See your authorized Audi dealer a s soon as
po ssible to restore full braking performance.
For mo re in format ion regarding the ABS
c:> page208.
The ABS warning light and the b rake warn
ing light come on together. The ABS will not
work and you will notice a change in braking response and performance.
Malfunction in the brake system
If the b rake warn ing lig ht <=:> page 18 and
the ABS wa rn ing illumina te
together there
may be a ma lf u nction in the ABS, an d there
may a lso be a malf unct ion in the brake system
itself
c:> ,&. .
In t he event o f a malfunction in the brake
system
the warn ing/indicato r light _
(USA
models) ,11 (Canada models) in the in
strument cluster flashes. By pressing the
! SE T!
b utton, you can bri ng up a dr iver message
which expla ins the ma lfu ncti on in more de
tail. Please note
c:> page 30 .
Malfunction in the electronic differential
lock (EDL)
The EDL works toget her with the ABS . The
A BS warning ligh t will come on if the re is a
malfunc tion in the EDL system
c:> page 205 .
See your au tho riz ed A ud i deale r as so on as
po ssib le.
.&_ WARNING
- If the m (U SA mode ls)/ 11] (Canada
mode ls) warn ing light does not go o ut,
o r if it comes o n while driving, the ABS
system is not working prope rly. The veh i
cle can then be stopped only with the
standard brakes (without ABS). You will
not have the protection ABS provides .
Contact you r autho riz ed Aud i d ea le r as
soo n as poss ible.
- USA models: If the - warning ligh t
and
t h e m warning ligh t come on to
ge ther, the rear w heels could loc k up
firs t un der har d b ra king. Rear wheel l ock
up c an c ause loss o f vehicle con trol an d
an acc iden t. H ave your ve hicle re paired
-
immed iate ly by yo ur autho rize d Au di
dea le r o r a qua lified w ork shop. Drive
slowly and avo id sudden, hard brake a p
plications.
- Canada models: If the brake warning
light . and the ABS war ning light
li]
come on togethe r, th e rear whe els could
loc k up firs t und er hard braking. Rear
wheel lock -up can caus e loss o f vehicle
con trol and an a ccide nt. Have yo ur vehi
cle re pa ire d imme diately by your author
i z ed A udi d ealer o r a qu alifie d wor ksh op.
D rive s low ly and avoid s udden, hard
brake applications .
:ru I<®> Electromechanical parking brake
The warning/indicator light monitors the
elec tromechanical parking brake.
Wi th t he pa rking brake applied and the igni
tio n tu rn e d on, the. (US A
models) ,11 (C an
ad a models) warn ing/indi cator lig ht ill umi
nates . After the ignition has been t urne d off,
the wa rn ing/ indicato r light cont inues to ill u
minate for about 30 seconds . If the parking
brake is applied w ith the ign ition t urned off,
the war ning/ indicato r light illum inates for
abo ut 30 seconds .
The wa rning/indicator light wi ll go out when
the pa rking bra ke is re leased .
If the warning/indicator light flas hes continu
o us ly
after applying the parking bra ke, brak
ing fo rce is not s uff icient to prevent the vehi
cle from rolling unintentionally . Please note
the followi ng:
- If the slo pe of the ground is too steep to
park the vehicle, the addit ional drive mes
sage appea rs
Caution : Vehicle parked too
steep .
- In the eve nt of a pa rking bra ke malfunction,
the yellow
IIJ symbol appears in the instr u
ment cluste r display a nd the driver message
Parking brake malfunction! is display ed .
Have t he ma lf u nct ion r epair ed as soon as
po ssible by a n authoriz ed Audi dea le r or a ny
o th er q ualifi ed w orksh op.
Page 20 of 316

18 Instrum ent s and w arn ing /indic ato r light s
BRAKE/ CQ)) Brake system
The warning/indicator light flashes if brake
fluid level is low, if there is an ABS system
malfunction or a parking brake malfunction.
The 1111 (USA models)/ . (Canada models)
light illuminates when the ign ition is turned
on .
It goes out after the engine has been
started. This indicates t hat the brake war ning
light is funct ion ing properly.
If th e br ake w ar ning light d oes not light up
w hen the engin e is c ranking , th ere ma y be a
ma lfun cti on in th e ele ctric al sys tem. In thi s
case, c ontact an auth oriz ed Audi d eale r.
If the brake system warning/ind icator light
flashes, there is a brake system malfunction .
By pressing the
ISE TI button, you can br ing up
a driver message which exp la ins the ma lfunc
tion in more detail
Q page 30.
If the ABS fails, the ABS warning/ind icator
light
B (USA mode ls)/ 11] (Canada mode ls)
flashes together w it h the brake system warn
ing/i ndicator light
Q & .
(USA models): If the 1111 warn ing light and
the
El warning light illuminate togethe r, im
mediately contact your author ized Audi dealer
or qualified workshop to have all bra ke pads
inspected
q page 34 .
When the light comes on, an audib le warni ng
signal is also give n.
A WARNING
- USA models: If the 1111 warning l ight
and
the m warning light come on to
gether, the rear wheels could lock up
first under hard braking . Rear wheel lock
up can cause loss of vehicle control and
an acc ident. Have your vehicle repaired
immediately by your authorized Audi
dealer or a qualified workshop . Dr ive
slowly and avoid sudden, hard brake ap·
plicat ions.
- Canada models: If the brake warn ing
light . and the ABS warning light
II]
come on together, the rear wheels could
.
lock up first under hard braking . Rear
wheel lock-up can cause loss of vehicle
control and an accident . Have your vehi
cle repaired immed iately by your author·
ized Audi dealer or a qualified workshop .
Drive s low ly and avoid sudden, hard
brake applications.
- If the brake warning/ind icator light does
not go ou t after a few seconds and the
pa rking brake released, or lights up wh ile
you are driv ing, the fluid level in the
brake fluid reservoir is too low. If yo u be
lieve that it is safe to do so, proceed im
mediately at low speed to the nearest
author ized Audi dealer or qualif ied repair
facility and have the brake system in·
spected.
- Always keep in mind that after severa l
brake applications, you will need greater
pressure on the brake pedal to stop your
veh icle. Do not rely on strained brakes to
respond with max imum stopping power
in critical s ituations. You must allow fo r
increased braking dis tances. The extra
distance used up by fading brakes could
lead to an accident.
Page 21 of 316

Driver information
display
Introduction
General notes
The driver informa tion display inside the in
strument cluster provides you, the driver,
with much useful information.
Fig. 9 Instr ument cluster: center d isplay
Information from the driver information sys
tem is shown in the display in the center of
the instrument cluster.
When you turn on the ignition and while you
are driving, some functions and vehicle com
ponents are scanned for their operating sta
tus. Malfunctions or required service proce
dures are signaled audibly and shown by red
and yellow lighted symbols and rem inders to
the dr iver in the display.
The driver is also shown information about ra
d io and CD operation and directions for the
nav igation system*. You can find add itional
i n formation on these subjects in the M MI
manual.
The illustrations in the instrument panel dis
play differ in some of the vehicles .
The driver information system provides the
following functions:
Sou nd system disp lay
¢page 19
Outside air temperature ¢ page 20
Gearshift indica tor * ¢ page 20
Digital speedometer ¢ page 21
Open door -and luggage com-¢page 21
partment warning
Driver inform ation di spl ay 19
Service interval display
Auto Chec k sys tem
Driver information
Speed warn ing
Trip computer*
Gearshift selector positions (Automatic transmission *)
Adaptive c ruise control*
a) Tips
¢page 21
¢page28
¢page29
¢page27
¢page22
cf) page 12 8
c::.page 102
In the event of a malfunction either a red
or yellow icon app ears in the display. Red
symbols indicate
Danger ¢ page 29. Yel
l ow symbo ls indicate a
Warning
¢page 33.
Sound system display
Fig. 10 Display: sound system
If priority 1 or pr iority 2 faults are not shown
by the Auto Check Contro l, the name of the ra
dio station you are t uned to o r the frequency
and the recept ion ran ge are shown in the up
per area of the d isplay .
When the CD is in use, the tit le of the track
being played is shown. The CD changer* dis
plays the number o f the cur rent C D (CDl to
CD6) .
Page 22 of 316

20 Driver in formation d ispl ay
Outside temperature display
Fig. 11 Display : outside te mperature
At temperatures below 41 °F (+S °C), a snow
flake symbol appears in front of the tempera ture display . It is intended to remind the driv
er to pay spec ial attent ion to
ic e on the roa d.
If your vehicle is stat ionary or if you are driv
ing at very low speeds, the temperature dis
played may be slightly higher than the actual
temperature outside due to the heat radiating
from the eng ine .
The unit of measurement for the temperature
can be set in either °For in °Con the MM I* or
on the radio control un it . The outside temper
ature display automatically shows the unit of
measurement that has been set. For addition
a l information, see the MMI* or the radio in
struction manua l.
_& WARNING
- Never use the outside temperature d is
play to determine if a road surface is icy
or not. Keep in mind that road surfaces,
especially bridges and overpasses, could
be ice covered and slippery even at an
outside temperature above 41 °F (+S
0 ().
-Always remember, even if the "snow
flake" symbol ( ice warn ing) does not ap
pear i n the display, blac k ice could be on
the road.
- Always reduce you r speed and drive with
special care in cold weather conditions
when the chance of encountering icy
road s urfaces increases .
'
(D Tips
-If the vehicle is stationary, or if you are
dr iving at a very low speed, the tempera
t u re shown in the d isp lay m ight be
slightly h igher than the actual outside
temperat ure. Th is is caused by the heat
being radiated from the engine .
Gearshift Indicator
Applies to vehicles: wit h manual transmiss ion and gear
shift indicato r
This indicator can help conserve fuel.
Fig. 12 D isp lay: Gea rs hi ft indicator
The rad io or MMI* can be used to act ivate or
deact ivate the gearshift ind icator .
Driving info rmati on· fading in and out
.,. Select: Function button ICAR ! > Instrument
cluster>
Shifting sugg estion .
In order to become familiar with the gearshift
indicter, at first just drive the way you are
used to.
If the current gear -and the dr iv ing
s ituation - is not the best one for conserving
fuel, then the indicator will disp lay the recom
mended gear . The display shows the current
gear and the gear that is recommended
r:::> fig . 12.
- Up shifting The display will light up to the
right of the gear cu rrently selected if it is
recommend ing a higher gear .
-Downshift ing: The display will light up to
the
left of the gear currently se lected if it is
recommend ing a lowe r gear .
Somet imes the i ndicator will recommend
sk ipping a gear (3
> 5).
Page 23 of 316

If there is no gearshift recommendation, then
just drive in the appropriate gear for conserv
ing fuel.
@ Tips
-This indicator can help you conserve fuel.
This indicator is not meant to show you
which gear you should a lways be in in all
driving situations. Sometimes, in s itua
tions such as passing, driving through mountains or when towing a trailer,
there won't be any gearsh ift recommen
dat ion.
- The display does not light up when the
clutch pedal is be ing depressed .
Digital speedometer
Fig. 13 Display : Dig ital speedo mete r
Current speed appears in the display . Speed is
shown in 1 mph increments (USA models) or 1
km/h increments (Canada models) .
You can switch the display from miles to kilo meters and vice versa via the MMI*.
Open door or trunk lid warning
The pictogram alerts you when doors or the
trunk lid have been le~ open.
Fig. 14 Display: Open doo r- and trunk lid warning
Driver information display 21
The Open Door/Trunk Lid warning displays if
even
one door, the hood or the trunk lid is
open. Th is symbol also shows
which door or
lid has not been closed
q fig. 14 .
As soon as the door, the hood and the trunk
lid are closed properly, the door and trunk lid
warning turns off and the selected driver in
formation system functions are displayed
again.
Service interval display
The service interval display reminds you when
your next service is due .
Fig. 15 Disp lay : Se rv ice interval d isplay
The schedule for the next oil change or inspec
t ion is calculated automatically and d isp layed
accord ingly. The d isp lay works in two stages:
Service reminder
30 days before the next service is due, a serv
i ce reminder appears in the display when you
turn on the ignition
qfig . 15 .
After about 5 seconds the display switches
back to normal. The distance and time re
main ing are updated each time the ignit ion is
turned on until the date due for serv ice is
reached.
Service due
When the due date for service is reached, the
message
Service due! appears in the instru
ment cluster immed iately after you turn on
the ignition. Addit ionally, a warning tone
sounds. After about 5 seconds the disp lay
switches back to normal.
Page 24 of 316

22 Driver information display
Calling up the service schedules
If or when an oil change or inspection is due,
can be shown in the radio or MMI* display by
selecting the service interval display in the car menu. Select
ICARI > Service interval display.
Resetting the service interval display
Your authorized Audi dealer w ill reset the cor
responding service schedule after performing
the appropriate service on your vehicle. You
a lso have the possibility to reset the oil
change schedule after having performed an
oil change according to Audi specifications.
Select
I CAR I > Service interval dis play > Reset
oil change interval.
(D Note
If you disconnect the battery terminals, no
calculations can be made for the service
interval display during this t ime and no
service rem inder w ill appear . Remember
that observ ing the proper serv ice intervals
is vital ly important to extend ing the life of
your veh icle, part icular ly the engine, and
maintaining its va lue. Even if the mileage
driven is low, the maximum period of one
year from one service to the next must not be exceeded.
@ Tips
- Do not reset the display between oil
changes, otherw ise the display will be in
correct.
- The information in the Service Reminder
remains stored even when the vehicle
battery is disconnected.
Trip computer
Introduction
The trip computer gives you information on
current and average fuel mileage, average
speed, fuel range and driving time.
Fig. 16 Trip computer display: Average fue l mi leage
T he following information is con tinuously
evaluated by the trip computer and can be dis
played sequentially in the instrument cluster
display:
Fuel range
The estimated cruising range in miles (km)
appea rs in the display. This tells you how far
your vehicle will be ab le to travel on the cur
rent tank of fuel and with the same driving
style. The display changes in increments of 6
miles (10 km).
T he cruising range is calculated based on the
fuel consumption for the last 18 miles
(30 km). If you drive conservatively, the cruis
ing range will increase.
Average fuel mileage
T he average fuel economy in MPG (l/100 km)
since you last cleared the memory appears in
this display. You can use this display to adjust
your driving technique to achieve a desired
mileage.
Current fuel mileage
T he instantaneous fuel consumption in m iles
per gallon ( l/100 km) is shown in this display.
You can use this display to adjust your driving
technique to achieve a desired m ileage .
Ill-