2011 INFINITI QX56 fuse

TAIL LAMP CIRCUITEXL-109
< DTC/CIRCUIT DIAGNOSIS > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
TAIL LAMP CIRCUIT
BODY SIDE
BODY SIDE : Component Function CheckINFOID:0000000006213976
1.CHECK TAIL LAMP OPERATION
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, chec k that the tail lamp is turned ON.
Is the inspection result normal?
YES >> Tail lamp circuit is normal.
NO >> Refer to EXL-109, "
BODY SIDE : Diagnosis Procedure".
BODY SIDE : Diagnosis ProcedureINFOID:0000000006213977
1.CHECK TAIL LAMP FUSE
1. Turn ignition switch OFF.
2. Check that the following fuses are not fusing.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair the malfunctioning part before replacing the fuse.
2.CHECK TAIL LAMP OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Disconnect rear combination lamp connector.
2. Turn ignition switch ON.
3. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4. With operating the test items, check vo ltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 4.
3.CHECK TAIL LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect the following connectors.
- IPDM E/R
- Front combination lamp
- Rear combination lamp TAIL : Tail Lamp ON
Off : Tail lamp OFF
Unit Location Fuse No. Capacity
Tail lamp IPDM E/R #46
10 A
#47
(+)
(− )Test item Vo l ta g e
(Approx.)
IPDM E/R
Connector Terminal
E14 38
GroundEXTERNAL
LAMPS TAIL Battery voltage
Off 0 V
44 TAIL Battery voltage
Off 0 V
Revision: 2010 May2011 QX56

EXTERIOR LIGHTING SYSTEM SYMPTOMSEXL-113
< SYMPTOM DIAGNOSIS > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
SYMPTOM DIAGNOSIS
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom TableINFOID:0000000006213980
CAUTION:
Perform the self-diagnosis with CONS ULT-III before the symptom diagnosis. Perform the trouble diag-
nosis if any DTC is detected.
Symptom Possible cause Inspection item
Headlamp does not
switch to the high beam. One sideFuse
 Harness between IPDM E/R
and the front combination lamp
 Front combination lamp
(High beam solenoid)
 IPDM E/R
 Harness between the front com- bination lamp and ground Headlamp (HI) circuit
Refer to
EXL-86, "
Component
Function Check".
Both sides Symptom diagnosis
“BOTH SIDE HEADLAMPS DO NOT SWITCH TO HIGH BEAM”
Refer to
EXL-117, "
Diagnosis Procedure".
High beam indicator lamp is not turned ON.
[Headlamp (HI) is turned ON.] Combination meter Combination meter
Data monitor “HI-BEAM IND”
 BCM (HEAD LAMP) Active test “HEADLAMP”
Headlamp does not
switch to the low beam. One side
Front combination lamp (High
beam solenoid) —
Both sides  Combination switch
 Harness between the combina-
tion switch and BCM
BCM Combination switch
Refer to
BCS-80, "
Symptom Table".
High beam request signal
BCM
 IPDM E/R IPDM E/R
Data monitor “HL HI REQ”
IPDM E/R —
Headlamp is not turned
ON. One sideFuse
 Xenon bulb
 Harness between IPDM E/R
and the front combination lamp
 Front combination lamp (xenon
headlamp)
 IPDM E/R
 Harness between the front com- bination lamp and ground Headlamp (L
O) circuit
Refer to EXL-88, "
Component
Function Check".
Both sides Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to EXL-118, "
Diagnosis Procedure".
Headlamp is not turned
OFF. When the ignition
switch is turned ON
The ignition switch is
turned OFF (After acti-
vating the battery sav-
er).
IPDM E/R —
Revision: 2010 May2011 QX56

EXL-114
< SYMPTOM DIAGNOSIS >[XENON TYPE]
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Each lamp is not turned ON/OFF with lighting switch
AUTO. Combination switch
 Harness between combination
switch and BCM
BCM Combination switch
Refer to
BCS-80, "
Symptom Table".
 Optical sensor
 Harness between optical sen- sor and BCM
BCM Optical sensor
Refer to
EXL-102, "
Component
Function Check".
Front fog lamp is not
turned ON. One side
 Front fog lamp bulb
 Harness between IPDM E/R
and front fog lamp
 Front fog lamp
 IPDM E/R Front fog lamp circuit
Refer to
EXL-94, "
Component
Function Check".
Both sides Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to
EXL-120, "
Diagnosis Procedure".
Parking lamp is not turned ON.  Parking lamp bulb
 Harness between IPDM E/R
and front combination lamp
 Front combination lamp
 IPDM E/R Parking lamp
circuit
Refer to EXL-96, "
Component
Function Check".
Front side marker lamp is not turned ON.  Front side marker lamp bulb
 Harness between IPDM E/R
and front combination lamp
 Front combination lamp
 IPDM E/R Front side marker lamp circuit
Refer to
EXL-98, "
Component
Function Check".
Tail lamp or rear side
marker lamp is not turned
ON. Body side
 Harness between IPDM E/R
and rear combination lamp
 Rear combination lamp Tail lamp circuit (body side)
Refer to
EXL-109, "
BODY SIDE :
Component Function Check".
Back door side  Harness between IPDM E/R
and tail lamp (back door side)
 Tail lamp (back door side) Tail lamp circuit (back door side)
Refer to
EXL-110, "
BACK DOOR
SIDE : Component Function
Check".
License plate lamp is not turned ON.  License plate lamp bulb
 Harness between IPDM E/R
and license plate lamp
 License plate lamp License plate lamp circuit
Refer to
EXL-112, "
Component
Function Check".
Tail lamp, rear side marker lamp and license plate
lamp are not turned ON. Fuse
 Harness between IPDM E/R
and rear combination lamp (LH)
 IPDM E/R Tail lamp circuit (body side)
Refer to
EXL-109, "
BODY SIDE :
Component Function Check".
 Parking lamp, side marker lamp, tail lamp and li- cense plate lamp are not turned ON.
 Parking lamp, side marker lamp, tail lamp and li- cense plate lamp are not turned OFF.
(Each illumination is turned ON/OFF.) Symptom diagnosis
“PARKING, LICENSE PLATE, SIDE MARKER LAMP AND TAIL LAMPS
ARE NOT TURNED ON”
Refer to
EXL-119, "
Diagnosis Procedure".
Tail lamp indicator is not turned ON.
(Parking, side marker lamp and tail lamps are turned
ON.) Combination meter Combination meter
Data monitor “LIGHT IND”
 BCM (HEAD LAMP) Active test “TAIL LAMP”
Turn signal lamp does not
blink. Indicator lamp is nor-
mal.
(Applicable side per-
forms the high flasher
activation.)
 Harness between BCM and
each turn signal lamp
 Turn signal lamp bulb Turn signal lamp circuit
Refer to
EXL-99, "
Component
Function Check".
Indicator lamp is includ-
ed.  Combination switch
 Harness between combination
switch and BCM
BCM Combination switch
Refer to
BCS-80, "
Symptom Table".
Symptom Possible cause Inspection item
Revision: 2010 May2011 QX56

PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT TURNED ON
EXL-119
< SYMPTOM DIAGNOSIS > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT
TURNED ON
DescriptionINFOID:0000000006213986
The parking, license plate, tail lamps and side marker are not turned ON in any condition.
Diagnosis ProcedureINFOID:0000000006213987
1.CHECK FUSE
Check that the following fuse is fusing.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair the applicable circuit. And then replace the fuse.
2.COMBINATION SWITCH INSPECTION
Check combination switch. Refer to BCS-80, "
Symptom Table".
Is the combination switch normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning part.
3.CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1. Select “TAIL & CLR REQ” of IPDM E/R data monitor item.
2. With operating the lighting switch, check the monitor status.
Is the inspection result normal?
YES >> Replace IPDM E/R.
NO >> Replace BCM. Refer to BCS-81, "
Removal and Installation".
Location Fuse No. Capacity
IPDM E/R #46 10 A
#47 10 A
Monitor item Condition Monitor status
TAIL & CLR REQ Lighting switch 1ST On
OFF Off
Revision: 2010 May2011 QX56

EXL-120
< SYMPTOM DIAGNOSIS >[XENON TYPE]
BOTH SIDE FRONT FOG
LAMPS ARE NOT TURNED ON
BOTH SIDE FRONT FOG LA MPS ARE NOT TURNED ON
DescriptionINFOID:0000000006213988
The front fog lamps are not turned ON in any condition.
Diagnosis ProcedureINFOID:0000000006213989
1.CHECK FUSE
Check that the following fuse is fusing.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair the applicable circuit. And then replace the fuse.
2.COMBINATION SWITCH INSPECTION
Check combination switch. Refer to BCS-80, "
Symptom Table".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning part.
3.CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1. Select “FR FOG REQ” of IPDM E/R data monitor item.
2. With operating the front fog lamp switch, check the monitor status.
Is the item status normal?
YES >> GO TO 4.
NO >> Replace BCM. Refer to BCS-81, "
Removal and Installation".
4.FRONT FOG LAMP CIRCUIT INSPECTION
Check the front fog lamp circuit. Refer to EXL-94, "
Component Function Check".
Is the inspection result normal?
YES >> Replace IPDM E/R.
NO >> Repair or replace the malfunctioning part.
Unit Location Fuse No. Capacity
Front fog lamp IPDM E/R #50 15 A
Monitor item Condition Monitor status
FR FOG REQ Front fog lamp switch
(With lighting switch 1ST)ON On
OFF Off
Revision: 2010 May2011 QX56

EXL-126
< REMOVAL AND INSTALLATION >[XENON TYPE]
FRONT COMBINATION LAMP
Disconnect the battery negative terminal or remove the fuse.
1. Remove front grille. Refer to
EXT-19, "
Removal and Installation".
2. Remove front bumper molding. Refer to EXT-13, "
Removal and Installation".
3. Remove front bumper fascia. Refer to EXT-13, "
Removal and Installation".
4. Remove headlamp mounting bolts.
5. Pull out headlamp assembly forward vehicle.
6. Disconnect connectors before removing headlamp assembly.
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to EXL-121, "
description".
ReplacementINFOID:0000000006369465
CAUTION:
 Disconnect the battery negative terminal or remove the fuse.
 After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
 Never touch the glass of bu lb directly by hand. Keep grease an d other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
 Never leave bulb out of lamp reflector for a long ti me because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB (HI/LO)
1. Remove fender protector. Refer to EXT-23, "FENDER PROTECTOR : Removal and Installation".
2. Rotate resin cap counterclockwise and unlock it.
3. Rotate bulb socket counterclockwise and unlock it.
4. Remove retaining spring lock. And then remove bulb from headlamp housing assembly.
CAUTION:
Never break the xenon bulb ceramic tube when replacing
the bulb.
PARKING LAMP BULB
1. Remove hood switch*.
*:When replace a right.
2. Rotate bulb socket counterclockwise and unlock it.
3. Remove bulb from bulb socket.
FRONT TURN SIGNAL LAMP BULB
1. Remove hood switch*.
*:When replace a right.
2. Rotate bulb socket counterclockwise and unlock it.
3. Remove bulb from bulb socket.
SIDE MARKER LAMP BULB
1. Remove fender protector. Refer to EXT-23, "FENDER PROTECTOR : Removal and Installation"
2. Rotate bulb socket counterclockwise and unlock it.
3. Remove bulb from bulb socket.
JPLIA0919ZZ
Revision: 2010 May2011 QX56

EXL-128
< REMOVAL AND INSTALLATION >[XENON TYPE]
FRONT FOG LAMP
FRONT FOG LAMP
Exploded ViewINFOID:0000000006369467
Removal and InstallationINFOID:0000000006369468
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1. Remove front fender protector. Refer to
EXT-23, "FENDER PROTECTOR : Removal and Installation".
2. Remove front fog lamp finisher.
3. Disconnect front fog lamp harness connector.
4. Remove front fog lamp fixing screw.
5. Disengage pawl, and then remove front fog lamp.
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to EXL-123, "
Description".
ReplacementINFOID:0000000006369469
CAUTION:
 Disconnect the battery negative terminal or remove the fuse.
 Never touch the glass of bulb directly by hand. Keep grease an d other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
 Never leave bulb out of lamp reflector for a long ti me because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
FRONT FOG LAMP BULB
1. Remove front fender protector. Keep the service area. Refer to EXT-23, "FENDER PROTECTOR :
Removal and Installation".
1. Front bumper 2. Front fog lamp 3. Front fog lamp finisher
: Pawl
JMLIA1117ZZ
Revision: 2010 May2011 QX56

EXL-130
< REMOVAL AND INSTALLATION >[XENON TYPE]
SIDE TURN SIGNAL LAMP
SIDE TURN SIGNAL LAMP
Exploded ViewINFOID:0000000006369470
Removal and InstallationINFOID:0000000006369471
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
1. Remove the door mirror. Refer to
MIR-32, "DOOR MIRROR ASSEMBLY : Removal and Installation".
2. Remove the door mirror glass. Refer to MIR-35, "
GLASS MIRROR : Removal and Installation".
3. Remove the side camera finisher. Refer to MIR-33, "
DOOR MIRROR ASSEMBLY : Disassembly and
Assembly".
4. Remove side turn signal lamp fixing screws (E), and then remove side turn signal lamp (with side turn signal lamp models
only).
NOTE:
Pull slightly side camera finisher (1) covering side turn signal
lamp bottom screw.
INSTALLATION
Install in the reverse order of removal.
1. Door mirror assembly 2. Door mi rror cover 3. Side camera finisher
4. Side turn signal lamp housing 5. Side turn signal lamp bulb
JMLIA1110ZZ
JMLIA0914ZZ
Revision: 2010 May2011 QX56