2011 INFINITI QX56 fuse

EXTERIOR LAMP FUSEEXL-85
< DTC/CIRCUIT DIAGNOSIS > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
EXTERIOR LAMP FUSE
Diagnosis ProcedureINFOID:0000000006213954
1.CHECK FUSE
Check that the following fuses are not fusing.
Is the inspection result normal?
YES >> The fuse is normal.
NO >> Repair the applicable circuit. And then replace the fuse.
Unit Location Fuse No. Capacity
Headlamp HI (LH) IPDM E/R #52 10 A
Headlamp HI (RH) IPDM E/R #51 10 A
Headlamp LO (LH) IPDM E/R #53 15 A
Headlamp LO (RH) IPDM E/R #54 15 A
Front fog lamp IPDM E/R #50 15 A
Parking lamp (LH)
 Front side marker lamp (LH) IPDM E/R #46 10 A
 Parking lamp (RH)
 Front side marker lamp (RH) IPDM E/R #47 10 A
 Tail lamp (Back door side LH/RH)
 Tail lamp (Body side LH)
 License plate lamp
 Rear side mark er lamp (LH) IPDM E/R #46 10 A
 Tail lamp (Body side RH)
 Rear side mark er lamp (RH) IPDM E/R #47 10 A
Stop lamp FUSE BLOCK (J/B) #7 10 A
Back-up lamp IPDM E/R #55 10 A
Revision: 2010 May2011 QX56

EXL-86
< DTC/CIRCUIT DIAGNOSIS >[XENON TYPE]
HEADLAMP (HI) CIRCUIT
HEADLAMP (HI) CIRCUIT
Component Function CheckINFOID:0000000006213955
1.CHECK HEADLAMP (HI) OPERATION
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, che ck that the headlamp (HI) is turned ON.
NOTE:
ON/OFF is repeated 1 second each.
Is the inspection result normal?
YES >> Headlamp (HI) circuit is normal.
NO >> Refer to EXL-86, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006213956
1.CHECK HEADLAMP (HI) OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Turn ignition switch OFF.
2. Disconnect front combination lamp connector.
3. Turn ignition switch ON.
4. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
5. With operating the test items, check vo ltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK HEADLAMP (HI) OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connec tor and front combination lamp harness connector.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness.
3.CHECK HEADLAMP (HI) FUSE
1. Turn ignition switch OFF. Hi : Headlamp (HI) ON
Off : Headlamp (HI) OFF
(+)
(− ) Test item Vo l ta g e
(Approx.)
IPDM E/R
Connector Terminal
RH E1549
GroundEXTERNAL
LAMPS Hi Battery voltage
Off 0 V
LH 50 Hi Battery voltage
Off 0 V
IPDM E/R Front combination lamp Continuity
Connector Terminal Connector Terminal
RH E1549 E119
6 Existed
LH 50 E118
Revision: 2010 May2011 QX56

HEADLAMP (HI) CIRCUITEXL-87
< DTC/CIRCUIT DIAGNOSIS > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
2. Check that the following fuses are not fusing.
Is the inspection result normal?
YES >> Replace IPDM E/R.
NO >> GO TO 4.
4.CHECK HEADLAMP HIGH (HI) SHORT CIRCUIT
1. Disconnect IPDM E/R connector.
2. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES >> Replace fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO >> Repair or replace harness. And then replace the fuse.
5.CHECK HEADLAMP (HI) GROUND OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front combination lamp connector.
3. Check continuity between front combination lamp harness connector and ground.
Is the inspection result normal?
YES >> Replace front combination lamp.
NO >> Repair or replace harness.
Unit Location Fuse No. Capacity
Headlamp HI (RH) IPDM E/R #51
10 A
Headlamp HI (LH) #52
IPDM E/R
GroundContinuity
Connector Terminal
RH E1549
Not existed
LH 50
Front combination lamp
GroundContinuity
Connector Terminal
RH E119 2Existed
LH E118
Revision: 2010 May2011 QX56

EXL-88
< DTC/CIRCUIT DIAGNOSIS >[XENON TYPE]
HEADLAMP (LO) CIRCUIT
HEADLAMP (LO) CIRCUIT
Component Function CheckINFOID:0000000006213957
1.CHECK HEADLAMP (LO) OPERATION
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, che ck that the headlamp (LO) is turned ON.
Is the inspection result normal?
YES >> Headlamp (LO) is normal.
NO >> Refer to EXL-88, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006213958
1.CHECK HEADLAMP (LO) OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Turn ignition switch OFF.
2. Disconnect front combination lamp connector.
3. Turn ignition switch ON.
4. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
5. With operating the test items, check vo ltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK HEADLAMP (LO) OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connec tor and front combination lamp harness connector.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness.
3.CHECK HEADLAMP (LO) FUSE
1. Turn ignition switch OFF.
2. Check that the following fuses are not fusing. Lo : Headlamp (LO) ON
Off : Headlamp (LO) OFF
(+)
(− ) Test item Vo l ta g e
(Approx.)
IPDM E/R
Connector Terminal
RH E1552
GroundEXTERNAL
LAMPS Lo Battery voltage
Off 0 V
LH 51 Lo Battery voltage
Off 0 V
IPDM E/R Front combination lamp Continuity
Connector Terminal Connector Terminal
RH E1552 E119
5 Existed
LH 51 E118
Revision: 2010 May2011 QX56

HEADLAMP (LO) CIRCUITEXL-89
< DTC/CIRCUIT DIAGNOSIS > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
Is the inspection result normal?
YES >> Replace IPDM E/R.
NO >> GO TO 4.
4.CHECK HEADLAMP (LO) SHORT CIRCUIT
1. Disconnect IPDM E/R connector.
2. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES >> Replace fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO >> Repair or replace harness. And then replace the fuse.
5.CHECK HEADLAMP (LO) GROUND OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front combination lamp connector.
3. Check continuity between front combination lamp harness connector and ground.
Is the inspection result normal?
YES >> Perform the xenon headl amp diagnosis. Refer to EXL-90, "Diagnosis Procedure".
NO >> Repair or replace harness.
Unit Lotion Fuse No. Capacity
Headlamp LO (RH) IPDM E/R #54
15 A
Headlamp LO (LH) #53
IPDM E/R
GroundContinuity
Connector Terminal
RH E1552
Not existed
LH 51
Front combination lamp
GroundContinuity
Connector Terminal
RH E119 1Existed
LH E118
Revision: 2010 May2011 QX56

EXL-94
< DTC/CIRCUIT DIAGNOSIS >[XENON TYPE]
FRONT FOG LAMP CIRCUIT
FRONT FOG LAMP CIRCUIT
Component Function CheckINFOID:0000000006213962
1.CHECK FRONT FOG LAMP OPERATION
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the front fog lamp is turned ON.
Is the inspection result normal?
YES >> Front fog lamp circuit is normal.
NO >> Refer to EXL-94, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006213963
1.CHECK FRONT FOG LAMP FUSE
1. Turn ignition switch OFF.
2. Check that the following fuse is not fusing.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK FRONT FOG LAMP SHORT CIRCUIT
1. Disconnect front fog lamp connector.
2. Check continuity between IP DM E/R harness connector and ground.
Is the inspection result normal?
YES >> Replace fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO >> Repair or replace harness. And then replace the fuse.
3.CHECK FRONT FOG LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace bulb.
4.CHECK FRONT FOG LAMP OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Disconnect front fog lamp connector.
2. Turn ignition switch ON.
3. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4. With operating the test items, check vo ltage between IPDM E/R harness connector and ground.
Fog : Front fog lamp ON
Off : Front fog lamp OFF
Unit Location Fuse No. Capacity
Front fog lamp IPDM E/R #50 15 A
IPDM E/R
GroundContinuity
Connector Terminal
RH E1219
Not existed
LH 20
Revision: 2010 May2011 QX56

EXL-96
< DTC/CIRCUIT DIAGNOSIS >[XENON TYPE]
PARKING LAMP CIRCUIT
PARKING LAMP CIRCUIT
Component Function CheckINFOID:0000000006213964
1.CHECK PARKING LAMP OPERATION
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the parking lamp is turned ON.
Is the inspection result normal?
YES >> Parking lamp circuit is normal.
NO >> Refer to EXL-96, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006213965
1.CHECK PARKING LAMP FUSE
1. Turn ignition switch OFF.
2. Check that the following fuses are not fusing.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK PARKING LAMP SHORT CIRCUIT
1. Disconnect the following connectors.
- IPDM E/R
- Front combination lamp
- Rear combination lamp
- License plate lamp
2. Check continuity between IP DM E/R harness connector and ground.
Is the inspection result normal?
YES >> Replace fuse. (Replace IPDM E/R if fusing is found again.)
NO >> Repair or replace harness. And then replace the fuse.
3.CHECK PARKING LAMP BULB
Check applicable lamp bulb.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace bulb.
4.CHECK PARKING LAMP OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Disconnect front combination lamp connector.
2. Turn ignition switch ON. TAIL : Parking lamp ON
Off : Parking lamp OFF
Unit Location Fuse No. Capacity
Parking lamp IPDM E/R #46
10 A
#47
IPDM E/R
GroundContinuity
Connector Terminal
RH E1437
Not existed
LH 43
Revision: 2010 May2011 QX56

AFS SWITCHEXL-107
< DTC/CIRCUIT DIAGNOSIS > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
AFS SWITCH
Component Function CheckINFOID:0000000006213973
1.CHECK AFS SWITCH SIGNAL BY CONSULT-III
CONSULT-III DATA MONITOR
1. Turn ignition switch ON.
2. Select “AFS SW” of ADAPTIVE LIGHT data monitor item.
3. With operating the AFS switch , check the monitor status.
Is the inspection result normal?
YES >> AFS switch circuit is normal.
NO >> Refer to EXL-107, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006213974
1.CHECK AFS SWITCH FUSE
1. Turn ignition switch OFF.
2. Check that the following fuses is not fusing.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair the applicable. And then replace the fuse.
2.CHECK POWER SUPPLY CIRCUIT
1. Disconnect triple switch connector.
2. Check voltage between triple switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK AFS SWITCH CIRCUIT
1. Disconnect AFS control unit connector.
2. Check continuity between AFS control unit har ness connector and triple switch harness connector.
3. Check continuity between AFS control unit harness connector and ground.
Monitor item Condition Monitor status
AFS SW AFS switch ON On
OFF Off
Location Fuse No. Capacity
Fuse block (J/B) #3 10 A
(+) (–)Voltage (V)
(Approx.)
Triple switch
Connector Terminal M126 3 Ground Battery voltage
AFS control unit Triple switch Continuity
Connector Terminal Connector Terminal
M1353M1264Existed
AFS control unit GroundContinuity
Connector Terminal
M135 3 Not existed
Revision: 2010 May2011 QX56