2011 INFINITI QX56 fuse

WIPER AND WASHER FUSEWW-35
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K
M A
B
WW
N
O P
DTC/CIRCUIT DIAGNOSIS
WIPER AND WASHER FUSE
Diagnosis ProcedureINFOID:0000000006300467
1.CHECK FUSES
Check that the following fuses is not fusing.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace the fuse with a new one after repairing the applicable circuit.
Unit Location No. Capacity
Front wiper motor IPDM E/R 45 30 A
Headlamp washer relay - U 30 A
Washer pump Fuse block (J/B) 1 10 A
Revision: 2010 May2011 QX56

WW-40
< DTC/CIRCUIT DIAGNOSIS >
LIGHT & RAIN SENSOR
LIGHT & RAIN SENSOR
Component Function CheckINFOID:0000000006300475
1.CHECK FRONT WIPER AUTO OPERATION
1. Clean light & rain sensor detection area of windshield fully.
2. When the front wiper switch is turned to AUTO pos ition, front wiper operates once regardless of a rainy
condition.
Is front wiper (AUTO) operation normally?
YES >> Light & rain sensor circuit is normal.
NO >> Refer to WW-40, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006300476
1.CHECK LIGHT & RAIN SENSOR FUSE
1. Turn the ignition switch OFF.
2. Check that the light & rain sensor 10A fuse (#6) is not fusing.
Is the fuse fusing?
YES >> Replace the fuse after repairing the applicable circuit.
NO >> GO TO 2.
2.CHECK LIGHT & RAIN SENSOR POWER SUPPLY
1. Disconnect light & rain sensor connector.
2. Check voltage between light & rain sensor harness connector and ground.
Is the measurement value normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK LIGHT & RAIN SENSOR GROUND CIRCUIT
Check continuity between light & ra in sensor harness connector and ground.
Does continuity exist?
YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK LIGHT & RAIN SENSOR SIGNAL
1. Connect light & rain sensor connector.
2. Turn ignition switch ON.
3. Check signal between BCM harness connector and ground with oscilloscope.
(+)
(− ) Voltage (Approx.)
Light & rain sensor
Connector Terminal R9 1 Ground Battery voltage
Light & rain sensor GroundContinuity
Connector Terminal
R9 3 Existed
Revision: 2010 May2011 QX56

FRONT WIPER DOES NOT OPERATEWW-53
< SYMPTOM DIAGNOSIS >
C
DE
F
G H
I
J
K
M A
B
WW
N
O P
FRONT WIPER DO ES NOT OPERATE
DescriptionINFOID:0000000006300484
The front wiper does not operate under any operation conditions.
Diagnosis ProcedureINFOID:0000000006300485
1.CHECK WIPER RELAY OPERATION
CONSULT-III ACTIVE TEST
1. Select “FRONT WIPER” of IPDM E/R active test item.
2. With operating the test item, check front wiper operation.
Is front wiper operation normally?
YES >> GO TO 5.
NO >> GO TO 2.
2.CHECK FRONT WIPER MOTOR FUSE
Check front wiper motor fuse. Refer to WW-35, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace the fuse after repairing the applicable circuit.
3.CHECK FRONT WIPER MOTOR GROUND CIRCUIT
Check front wiper motor ground circuit. Refer to WW-39, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK FRONT WIPER MOTOR INPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Turn ignition switch OFF.
2. Disconnect front wiper motor connector.
3. Turn ignition switch ON.
4. Select “FRONT WIPER” of IPDM E/R active test item.
5. With operating the test item, check voltage between front wiper motor harness connector and ground.
Is the inspection result normal?
YES >> Replace front wiper motor.
NO >> Replace IPDM E/R.
5.CHECK FRONT WIPER REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1. Select “FR WIP REQ” of IPDM E/R data monitor item.
2. Switch the front wiper switch to HI and LO. Lo : Front wiper LO operation
Hi : Front wiper HI operation
Off : Stop the front wiper.
(+)
(− ) Condition Voltage (Approx.)
Front wiper motor
Connector Terminal
E42 1
Ground FRONT WIPER Lo Battery voltage
Off 0 V
4 Hi Battery voltage
Off 0 V
Revision: 2010 May2011 QX56