2011 INFINITI QX56 fuse

POWER SUPPLY AND GROUND CIRCUITADP-67
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
POWER SUPPLY AND GROUND CIRCUIT
DRIVER SEAT CONTROL UNIT
DRIVER SEAT CONTROL UNIT : Diagnosis ProcedureINFOID:0000000006248353
1.CHECK FUSE
Check that the following fuse and fusible link are not fusing.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace the blown fuse after repairing the affected circuit.
2.CHECK DRIVER SEAT CONTROL UNIT POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit connector.
3. Check voltage between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK DRIVER SEAT CONTROL UNIT GROUND CIRCUIT
Check continuity between the driver s eat control unit harness connector and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair or replace harness.
DRIVER SEAT CONTROL UNIT : Special Repair RequirementINFOID:0000000006248354
1.PERFORM ADDITIONAL SERVICE
Perform additional service when removing battery negative terminal.
>> Refer to ADP-51, "
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMI-
NAL : Description".
AUTOMATIC DRIVE POSITIONER CONTROL UNIT
AUTOMATIC DRIVE POSITIONER CO NTROL UNIT : Diagnosis Procedure
INFOID:0000000006248355
NOTE:
Do not disconnect the battery negative terminal and the dr iver seat control unit connector until DTC is con-
firmed with CONSULT-III.
1.CHECK FUSE
Check that the following fuse and fusible link are not fusing.
Signal name Fuse No.
Battery power supply K (50 A)
(+) (-)Voltage (V)
(Approx.)
Driver seat control unit
Connector Terminals B451 33 Ground Battery voltage
Driver seat control unit GroundContinuity
Connector Terminal
B451 43 Existed
Revision: 2010 May2011 QX56

ADP-68
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace the blown fuse after repairing the affected circuit.
2.CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit connector.
3. Check voltage between automatic drive posit ioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK AUTOMATIC DRIVE POSITION ER CONTROL UNIT GROUND CIRCUIT
Check continuity between the automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair or replace harness.
AUTOMATIC DRIVE POSITIONER CONTROL UNIT : Special Repair Requirement
INFOID:0000000006248356
1.PERFORM ADDITIONAL SERVICE
Perform additional service when removing battery negative terminal.
>> Refer to ADP-51, "
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMI-
NAL : Description".
Signal name Fuse No.
Battery power supply K (50 A)
(+) (-)Voltage (V)
(Approx.)
Automatic drive positioner control unit
Connector Terminals M104 25 Ground Battery voltage
Automatic drive positioner control unit GroundContinuity
Connector Terminal
M104 30 Existed
Revision: 2010 May2011 QX56

ADP-120
< DTC/CIRCUIT DIAGNOSIS >
SEAT MEMORY INDICATOR
SEAT MEMORY INDICATOR
Component Function CheckINFOID:0000000006248417
1.CHECK FUNCTION
1. Select “MEMORY SW INDCTR” in “A ctive test” mode with CONSULT-III.
2. Check the memory indicator operation.
Is the operation of relevant parts normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-120, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000006248418
1.CHECK SEAT MEMORY SWITCH INDICATOR OPERATION
Check seat memory switch indicator operation.
Which is the malfunctioning indicator?
All indicators are NG>>GO TO 2.
An indicator is NG>>GO TO 4.
2.CHECK FUSE
1. Turn ignition switch OFF.
2. Check that the blown fuse after repairing the affected circuit if a fuse is blown.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
3.CHECK SEAT MEMORY SWITCH INDICATOR POWER SUPPLY
Check voltage between seat memory switch harness connector and ground.
Is the inspection result normal?
YES >> Replace seat memory switch.
NO >> Repair or replace harness or connector.
4.CHECK SEAT MEMORY SW ITCH INDICATOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver seat control uni t and seat memory switch connector.
3. Check continuity between driver seat control unit harness connector and seat memory switch harness
connector.
Te s t i t e m D e s c r i p t i o n
MEMORY SW INDCTR OFF
Memory switch indicatorOFF
ON-1 Indicator 1: ON
ON-2 Indicator 2: ON
Signal name Fuse No.
Battery power supply 10 (10 A)
(+) (-)Voltage (V)
(Approx.)
Seat memory switch
Connector Terminals D13 5 Ground Battery voltage
Revision: 2010 May2011 QX56

AV
POWER SUPPLY AND GROUND CIRCUITAV-161
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B A
O P
POWER SUPPLY AND GROUND CIRCUIT
AV CONTROL UNIT
AV CONTROL UNIT : Diagnosis ProcedureINFOID:0000000006216319
1.CHECK FUSE
Check for blown fuses.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT
Check voltage between AV control unit harness connectors and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check harness between AV control unit and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect AV control unit connectors.
3. Check continuity between AV control unit harness connectors and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
FRONT DISPLAY UNIT
FRONT DISPLAY UNIT : Diagnosis ProcedureINFOID:0000000006216320
1.CHECK FUSE
Check for blown fuses.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT
Check voltage between front display unit harness connector and ground.
Power source Fuse No.
Battery 35
Ignition switch ACC or ON 19
Signal name Connector Terminal Ignition switch position Value (Approx.)
Battery power supply M208 19 OFF Battery voltage ACC power supply M208 7 ACC Battery voltage
Signal name Connector Terminal Ignition switch position Continuity Ground M208 20 OFF Existed
Power source Fuse No. Battery 35
Ignition switch ACC or ON 19
Revision: 2010 May2011 QX56

AV-162
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check harness between front display unit and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front display unit connector.
3. Check continuity between front display unit harness connector and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
HEADREST DISPLAY UNIT
HEADREST DISPLAY UNIT : Diagnosis ProcedureINFOID:0000000006216321
1.CHECK FUSE
Check for blown fuses.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT
Check voltage between headrest display unit harness connector and ground.
 *1: Headrest display unit LH
 *2: Headrest display unit RH
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check harness between headrest display unit and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect headrest display unit connector.
3. Check continuity between headrest display unit harness connector and ground.
 *1: Headrest display unit LH
 *2: Headrest display unit RH
Signal name Connector Terminal Ignition switch position Value (Approx.)
Battery power su pply M215 11 OFF Battery voltage
ACC power supply M215 23 ACC Battery voltage
Signal name Connector Terminal Ignition switch position Continuity Ground M215 12 OFF Existed
Power source Fuse No. Battery 35
Signal name Connector Terminal Ignition switch position Value (Approx.)
Battery power supply B554
*1
B574*2
2
OFF Battery voltage
4
Signal name Connector Terminal Ignition switch position Continuity
Ground B554
*1
B574*2
1
OFF Existed
3
Revision: 2010 May2011 QX56

AV
POWER SUPPLY AND GROUND CIRCUITAV-163
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B A
O P
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
VIDEO DISTRIBUTOR
VIDEO DISTRIBUTOR : Diagnosis ProcedureINFOID:0000000006216322
1.CHECK FUSE
Check for blown fuses.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT
Check voltage between video distributor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check harness between video distributor and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect video distributor connector.
3. Check continuity between video distributor harness connector and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
BOSE AMP.
BOSE AMP. : Diagnosis ProcedureINFOID:0000000006216323
1.CHECK FUSE
Check for blown fuses.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT
Power source Fuse No.
Battery 35
Ignition switch ACC or ON 19
Signal name Connector Terminal Ignition switch position Value (Approx.)
Battery power supply M217 2 OFF Battery voltage ACC power supply M217 4 ACC Battery voltage
Signal name Connector Terminal Ignition switch position Continuity Ground M217 1 OFF Existed
Ground M217 3 OFF Existed
Power source Fuse No. Battery 5
Battery 8
Revision: 2010 May2011 QX56

AV-164
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
Check voltage between BOSE amp. harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check harness between BOSE amp. and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BOSE amp. connector.
3. Check continuity between BOSE amp. harness connector and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
AROUND VIEW MONITOR CONTROL UNIT
AROUND VIEW MONITOR CONTRO L UNIT : Diagnosis ProcedureINFOID:0000000006216324
1.CHECK FUSE
Check for blown fuses.
Is inspection result normal?
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUITS
Check voltage between around view monitor control unit harness connector and ground.
Is inspection result normal?
YES >> GO TO 3.
NO >> Check harness between around view monitor control unit and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit connector.
3. Check continuity between around view m onitor control unit harness connector and ground.
Is inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
Signal name Connector Terminal Ignition switch position Value (Approx.)
Battery power supply B229 10 OFF Battery voltage
Battery power supply B229 11 OFF Battery voltage
Signal name Connector Terminal Ignition switch position Continuity Ground B229 12 OFF Existed
Power source Fuse No. Battery 9
Ignition switch ACC 19
Signal name Connector Terminal Ignition switch position Value (Approx.)
Battery power supply M4 82OFFBattery voltage
ACC power supply M48 4 ACC Battery voltage
Signal name Connector Terminal Ignition switch position Continuity
Ground M48 1 OFF Existed
Revision: 2010 May2011 QX56

AV
POWER SUPPLY AND GROUND CIRCUITAV-165
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B A
O P
SONAR CONTROL UNIT (WITH AROUND VIEW MONITOR)
SONAR CONTROL UNIT (WITH AROUND VIEW MONITOR) : Diagnosis Procedure
INFOID:0000000006216325
1.CHECK FUSE
Check for blown fuses.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between sonar control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace sonar control unit power supply harness.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect sonar control unit connector.
3. Check continuity between sonar control unit harness connector and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair or replace sonar control unit ground harness.
Power source Fuse No.
Ignition switch ACC or ON 19
Signal name Connector Terminal Ignition switch position Value (Approx.)
Battery power supply M47 13 ACC Battery voltage
Signal name Connector Terminal Ignition switch position Continuity Ground M47 24 OFF Existed
Revision: 2010 May2011 QX56