2010 SKODA OCTAVIA TOUR Columbus Navigation System Manual

Unlocking and locking
40WARNING
If the vehicle is locked from the outside and the safe securing system is acti-
vated, there must not be any person in the vehicle as it is then not possible to
open either a door or a window from the inside. The locked doors make it more
difficult for rescuers to get into th e vehicle in an emergency - hazard!
Note

Operate the radio remote control only when the doors and boot lid are closed and
you have visual contact with the vehicle.

Once in the car, you must not press the lock button
 of the radio remote control
before inserting the key into the ignition lock in order to avoid the car being inadvert-
ently locked and the alarm system* being switched on. Should this happen, press the
unlock button
 of the radio remote control.
Synchronisation of the remote controlIf the vehicle cannot be unlocked by actuatin g the remote control system then it is
possible that the code in the key and the co ntrol unit in the vehicle are no longer
synchronised. This can occur when the butt ons on the radio-operated key are actu-
ated a number of times outside of the operative range of the equipment or the battery
on the remote control was replaced.
This means it is necessary to synchronise the code as follows:
Press any button on the remote control.

pressing of the button means that the d oor will unlock with the key within 1
minute.
Anti-theft alarm system*DescriptionThe anti-theft alarm system increases the leve l of protection against people seeking to
break into the vehicle. The system triggers audible and visual warning signals if an
attempt is made to break into the vehicle. Optical and acoustic signals alert if an alarm
has been triggered (the turn signal lights
flash and the signal horn honks).
How is the alarm system activated?
The anti-theft alarm system is activated au tomatically when the vehicle is locked with
the key on the driver's door or by using th e radio remote control. It is activated 30
seconds after locking the door.
How is the alarm system deactivated?
The anti-theft alarm system is deactivated if the vehicle is unlocked by only using the
radio remote control. The anti-theft alarm system is reactivated if the vehicle is not
opened within 30 seconds after transmitting the radio signal.
Once you unlock the vehicle by inserting the ke y into the driver door you then have to
insert the key into the ignition lock and sw itch the ignition on within 15 seconds after
unlocking the door in order to deactivate the anti-theft alarm system. The alarm will
be triggered if you do not switch on the ignition within 15 seconds.
When is the alarm triggered?
The following security areas of the locked vehicle are monitored:

Bonnet,

Boot lid,

Doors,

Ignition lock,

Vehicle interior
4),

A drop in voltage of the on-board power supply.
An alarm is immediately triggered if either of the two battery terminals is disconnected
while the anti-theft alarm system is activated.
Deactivation of interior monitor
The process of switching off and switching on the interior monitoring system is the
same as for switching off and switching on the safe securing system page 36.
4)The alarm will be triggered through movement of occupants within the interior of the vehicle or
an attempt to steal the radio. The rear part of the interior of the vehicle is not fully monitored
under certain circumstances.
s2rc.book Page 40 Thursd ay, April 22, 2010 10:58 AM

Unlocking and locking41
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
This function makes it possible for example to leave animals in the vehicle.
How is the alarm switched off?
You switch the alarm off if you unlock the vehicle with the radio remote control or if
you switch the ignition on.
Note

The working life of the alarm siren is 5 years. More detailed information is available
by a specialist garage.

Before leaving the car, check that all the doors, windows and the electric
sliding/tilting roof* are properly closed in order to ensure that the anti-theft alarm
system is fully operational.

Coding of the radio remote control and th e receiver unit precludes the use of the
radio remote control from other vehicles.
Power windows*Buttons on the driver's doorThe power windows operate only when igniti on is switched on. After switching the
ignition off, the power windows can sti ll be operated however for maximum 10
minutes if a front door is not opened.
Opening a window– A window is opened by pressing lightly on the respective button in the door. The process stops when one releases the button.
– Additionally you can open the window automatically (fully open ed) by pressing the
button up to the stop. Renewed pressing of the button causes the window to stop
immediately.Closing a window– A window is closed through pulling lightly on the respective button in the door. The
closing process stops when one releases the button.
– Additionally you can close the window automatically (fully closed) by pulling the button up to the stop. Renewed pulling of the button causes the window to stop
immediately.
The buttons for the individual windows are lo cated in the armrest of the driver's door
 fig. 36 , front passenger door and in the rear doors*.
Buttons for the power windows in the armrest for the driver Button for the power window in the driver's door
Button for the power window in the front passenger's door
Button for the power window in the rear door on the right*
Button for the power window in the rear door on the left*
Safety pushbutton*
Safety pushbutton*
You can deactivate the buttons for power wind ows at rear doors by pressing the safety
pushbutton fig. 36 . The buttons for power windows at rear doors are activated
again by pressing the safety pushbutton again.
If the buttons for the rear doors are deactivated, the indicator light
 in the safety
switch lights up.
Fig. 36 Buttons on the driver's
door
AAABACADAS
AS
AS
AS
s2rc.book Page 41 Thursd ay, April 22, 2010 10:58 AM

Unlocking and locking
42WARNING

If you lock the vehicle from the outside, do not leave any person in the
vehicle since it is no longer possible to open the windows from the inside in an
emergency.

The system is fitted with a force limiter page 42. If there is an obstacle, the
closing process is stopped and the window goes down into the opened position.
You should then take particular care when closing the windows! You may
otherwise suffer severe injuries as a re sult of getting an arm, for example,
jammed in the window!

It is recommended to deactivate the el ectrically operated power windows in
the rear doors (safety pushbutton) page 41, fig. 36 when children are
being transported on the rear seats.Note

Other switches have only two positions for opening and closing the window. The
switch must be held until the window is opened or closed.

After switching the ignition off, it is still possible to open or close the windows for
a further 10 minutes. The automatic window cl osing will not operate during this time.
The power windows are switched off complete ly once you open the driver or front
passenger door.

When driving always use the existing he ating, air conditioning and ventilation
system for ventilating the interior of the vehicle. If the windows are opened, dust as
well as other dirt can get into the vehicle and in addition the wind noise is more at
certain speeds.
Button in the front passenger door and in the rear doorsA button for the relevant window is provided in these doors.Opening a window– Lightly press the appropriate button down and hold it until the window has moved
into the desired position.
Closing a window– Lightly press the appropriate button up and hold it until the window has moved
into the desired position.
WARNING
The system is fitted with a force limiter page 42. If there is an obstacle, the
closing process is stopped and the window goes down. You should then take
particular care when closing the wind ows! You may otherwise suffer severe
injuries as a result of getting an arm, for example, jammed in the window!
Note
After switching the ignition off, it is still possible to open or close the windows for a
further 10 minutes. The automatic closing and opening functions will not operate
during this time. The power windows are sw itched off completely once you open the
driver or front passenger door.Force limiter of the power windowsThe electrically operated power windows are fitted with a force limiter. It reduces the
risk of bruises or injuries when closing the windows.
If there is an obstacle, the closing process is stopped and the window goes down into
the opened position.
You must try to close the window once ag ain within 10 seconds after the window has
gone down and if the obstacle was not yet removed, the closing process is stopped.
During this time it is not possible to automatically close the window.
The force limiter is only switched off, if you attempt to close the window within the next
10 seconds - the window closes now with full strength!
If you wait longer than 10 seconds, th e force limiter is switched on again.
WARNING
You should take particular care when closing the windows! You may otherwise
suffer severe injuries as a result of get ting an arm, for example, jammed in the
window!
AS
s2rc.book Page 42 Thursd ay, April 22, 2010 10:58 AM

Unlocking and locking43
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Window convenience operationYou can open and close the electrically po wered windows as follows when unlocking
and locking the vehicle (only close the sliding/tilting roof):Opening a window– Hold the key in the locking cylinder of the driver's door in the unlock position until
all the windows are opened.Closing a window– Hold the key in the locking cylinder of the dr iver's door in the lock position until all
the windows are closed.
You can interrupt the opening or closing operation of the windows immediately by
releasing the key.
WARNING

There must not be any persons in th e vehicle which is locked from the
outside. After approx. 10 minutes have expired or after opening and closing the
vehicle door when the ignition is switched off, the windows can no longer be
opened.

The person who operates the convenie nce system must take extra care,
when closing the window, that no passengers suffer any injuries.Note
Obstruction protection is not active during the convenience operating feature.Operational faultsElectrically operated power windows do not operate
If the battery of the car has been disconne cted and then reconnected, the electrically
operated power windows do not operate. The system must be activated. Proceed as
follows in order to re-establish the function:

Hold the key in the locking cylinder of the driver's door in the lock position until all
the windows are closed,

Release the key,

Hold the key again in the lockin g position for about 3 seconds.
Operation in winter
Ice accumulating on the surface of the wi ndows during the winter may result in a
greater resistance when closing the windows and the window may stop and go down
several centimetres
Proceed as follows to close the window fully:

Hold the key in the locking cylinder of the driver's door in the lock position until all
the windows are closed,

Repeat this operatiive cy cle when the window stops.
WARNING
The system is fitted with a force limiter page 42. If there is an obstacle, the
closing process is stopped and the window goes down by several centimeters.
You should then take particular care when closing the windows! You may
otherwise suffer severe injuries as a re sult of getting an arm, for example,
jammed in the window!
s2rc.book Page 43 Thursd ay, April 22, 2010 10:58 AM

Unlocking and locking
44
Electric sliding/tilting roof*DescriptionThe sliding/tilting roof is operated by means of the control dial fig. 37 and only func-
tions when the ignition is switched on. The control dial has several positions.
After switching the ignition off, it is still possible to open, close and tilt the sliding/tilting
roof for approx. 10 minutes. It is no longer possible to operate the sliding/tilting roof
after opening one of the front doors, however.
Note

If the battery has been disconnected an d reconnected, it is possible that the
sliding/tilting roof does not close fully. Here you have to set the control dial to the
switch position and press it forward for about 10 seconds.

It is necessary after each emergency op eration (using crank handle) to move the
sliding/tilting roof into the ba sic position. Here you have to set the control dial to the
switch position and press it forward for about 10 seconds.
Opening and tiltingComfort position– Turn the switch to position fig. 37 .
Opening fully– Turn the switch to position and hold it in this position (spring-tensioned posi-
tion).Tilting roof– Turn the switch to position .
When the sliding/tilting roof is in the comfort position, the intensity of the wind noise
is much less.
The sun screen is also opened automatically when the roof slides open. You can slide
the sun screen into the opened or closed position by hand when the sliding/tilting roof
is closed.
Caution
It may be necessary during winter to remove any ice and snow in the area of the
sliding/tilting roof before opening it in order to prevent damaging the opening
mechanism.ClosingSliding closed/closing the sliding/tilting roof– Turn the switch to position fig. 37 .
Safety closing
The sliding/tilting roof is fitted with a force limiter. If an obstacle (e.g. ice) prevents
closing, the sliding/tilting roof stops and opens completely. You can close the
sliding/tilting roof completely without forc e limiter by pressing the switch to the
position fig. 37 at the front for as long as it take s for the sliding/tilting roof to close
completely .
WARNING
Close the sliding/tilting roof carefully - risk of injury!
Fig. 37 Control dial for the
power sliding/tilting roof
AAAA
AC
ABADAA
AA
s2rc.book Page 44 Thursd ay, April 22, 2010 10:58 AM

Unlocking and locking45
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Convenience operationYou can also close an open sliding/tilting roof from the outside.
– Hold the key in the locking cylinder of the driver's door in the lock position until the
sliding/tilting roof is closed .
The closing process stops when one releases the key.
WARNING
Close the sliding/tilting roof carefully - ri sk of injury! The force limiter does not
operate with the convenience closing.Emergency operation
You can close and/or open the sliding/tiltin g roof by hand if the system is defect.
– Position the flat blade of a screwdriver carefully against the rear edge of the cover of the electrical drive.
–Pull the cover down fig. 38 .
– Insert an Allen key, Group 4, up to the stop into the opening and close and/or open the sliding/tilting roof.
– Press on the cover again by first of all inserting the plastic lugs and then pushing
the cover up.
– Have the malfunction rectified by a specialist garage.
Note
It is necessary after each emergency op eration (using Allen key) to move the
sliding/tilting roof into the basic position . Here you have to turn the control dial
forward to the switch position page 44, fig. 37 and press for about 10 seconds.
Fig. 38 Detail of the headliner:
point for positioning screwdriverFig. 39 Detail of the headliner:
Emergency operation
AA
s2rc.book Page 45 Thursd ay, April 22, 2010 10:58 AM

Lights and Visibility
46
Lights and VisibilityLightsSwitching lights on and offSwitching on side lights– Turn the light switch into position
.
Switching on the low beam and main beam– Turn the light switch into position
.
– Press the main beam lever forward in order to switch on the main beam page 49, fig. 45 .
Switching off all lights– Turn the light switch into position°0.Switching on daylight driving lights*– Remove the cover of the fuse box on the left side of the dash panel page 177.
– Insert the activation fuse No. 17 in the fuse box.
Switching off daylight driving lights*– Remove the cover of the fuse box on the left side of the dash panel page 177.
– Take the activation fuse No. 17 out of the fuse box.
Low beam comes on only if the ignition is switched on. After switching off the ignition,
the low beam is switched off automatica lly and only the side lights come on.
On models fitted with right-hand steering the position of certain switches differs
from that shown in fig. 40 . The symbols which mark the switch positions are iden-
tical.
In certain countries, the low beam is on a reduced brightness as well as the side lights,
when the ignition is switched on.
WARNING
Never drive with side lights on - risk of accident! The side lights are not bright
enough to light up the road sufficiently in front of you or to be seen by other
oncoming traffic. In this case, always switch on the low beam when it is dark or
if visibility is poor.
Note

An audible warning will sound if you wi thdraw the ignition key and open the
driver's door when the vehicle lights are still on.

The acoustic warning signal is switched off over the door contact when the driver's
door is closed (ignition off). The vehicle can be parked with the side lights on.

If the car is parked for a lengthy period, we recommend switching off all lights, or
leaving only the parking lights switched on.

The switching on of the described lights should only be undertaken in accordance
with the legal requirements.

If a fault occurs in the light switch , the low beam comes on automatically

In the event of cool or humid weather conditions, the headlights can be misted up
from inside.
Fig. 40 Dash panel: Light switch
s2rc.book Page 46 Thursd ay, April 22, 2010 10:58 AM

Lights and Visibility47
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data

The temperature difference between interior and external area of the headlight
lenses is decisive.
 When the driving lights are switched on, the light outlet surfaces are free from
mist after a short period. The headlight le nses can possibly mist up at the border
areas.
 It also concerns reverse light and turn signal lights.
 This mist has no influence on th e life of the lighting system.
Fog lights*

Switching on the fog lights– First of all turn the light switch into position
 or   fig. 41 .
– Pull the light switch into position .
If the fog lights are switched on, the symbol
 next to the light switch is more brightly
illuminated as well as the warning light in the instrument cluster page 27.
Rear fog light

Switching on the rear fog light– First of all turn the light switch into position
 or   fig. 41 .
– Pull the switch into position . If the vehicle is not fitted with fog lights*, th
e rear fog light is switched on by turning the
light switch to the position
 and is pulled out directly to the position . This switch
does not have two positions, but only one position.
The warning light
 lights up in the instrument cluster when the rear fog light is
switched on page 25.
Only the rear fog light of the trailer lights up automatically when you are towing a
trailer using a factory-fitted towing device which is fitted with the rear fog light.
The rear fog light is located in the rear light array on the driver's side.
Caution
The rear fog light should only be switched on if visibility is particularly poor (conform
with any varying legal provisions) to avoi d dazzling vehicles behind your vehicle.Instrument lighting*

You can adjust the brightness of the instrument lighting.Instrument lighting– Switch on the light.
– Turn the control dial fig. 42 to the desired intensity of the instrument lighting.
Fig. 41 Dash panel: Light switch
A1
A2
A2
Fig. 42 Dash panel: Instrument
lighting
s2rc.book Page 47 Thursd ay, April 22, 2010 10:58 AM