2010 AUDI S8 Owners Manual

________________________________________________ F_ u_s _e_ s_ a_ n_ d_ b_u_ lb_ s _ __.1111
(]] Tips
You a re well adv ised to keep a supply of spare fuses in your veh icle .
Fuses with the proper ampere ratings are avai lab le at your Audi
dealer. •
Fuse Location, Instrument Panel left
Fig. 2 78 Fuse pa nel
la you t
Some of the equ ipment items listed a re opt io na l o r only availab le on
certain model configurations.
Note that the following table i s accu rate at the time of going to
pre ss and is subject to change . In the event of di scr epancie s, th e
label on the in side of the cover always takes precedence.
T he power wi ndows and the power seats are p rotected by cir cuit
breakers ,
which automatically reset after a few seconds after the
overlo ad -for e xamp le if a window is fro zen - has bee n remed ie d.
Equipment Amps
1 Garage door opener (Homelink) 5
Parking assist system 5
3
Pa rking assist sy stem 5
4
Headlight range control/light control devic e 10
Vehicle OP-eration
No.
5
6
7
8
9
10
11
1 2
13
14
1 5
16
17
1 8
19
20
2 1
22
23
24
25
26
27
28 29
Equipment Amps
Instrument cluster 5
Steering column electronics system control 10
Diagnostic co nnector 5
Diagnostic connector/oil level sensor 5
ES P contro l uni t/steer ing angle se nsor 5
Instrum ent cluster 5
Au di lane ass ist 10
B ra ke ligh t switch 5
Telephone/ cell phone 10
Vacant
Acces s/ st art cont rol m odul e
5
RSE system 10
Adaptive C ruise Control 5
Hea ted w asher je ts 5
Vacant
Tire pressure monitoring system *
5
Vacant
Bra ke light switch
5
Ce ll phone preparation 5
Horn 15
Wi ndshie ld wipe r system 4 0
Vacant
E le ctronic Stabilizati on Pro gram (E SP)
2 5
Vacant
Sw itch illumination
1
Vehicle care Do-it-yourself service iTechnical data

lffll.,___F_ u_ s_e _ s_ a_n_ d_ b_u _ l_ b_ s _______________________________________________ _
No. IIEquipment
30 Vacant
31
32
33
34
35
36
37
38
39
4 0
41
42 Onboard power s
upply, light contro l (r ight
headlight)
Vacant L eft rea r footwell heate r
Vacant
Vaca nt
A udi si de assist
Coo ler
Onboard power supply, light control (left head­
light)
Door control un it, dr iver's side
Power steerin g column adjustmen t
Door control unit, rear left
Access/start control module
4 3 Adaptive L ight, le ft
--44 Adap tive Light, righ t
Amps
30
25
5
15
30
7 .5
25
7 .5
25
10
10
•
Fuse Location, Instrument Panel right
Fig. 279 Fuse panel
la yout
Some of the equipment items listed are optiona l or only availab le on
certain mode l configurations .
Note that the following table is accurate at the time of going to
press and is subject to change. In the event of discrepancies , the
label on the in sid e of the cover alway s take s precedence .
The power window regu lators and the power seats are protected by
circuit breakers , which automatically reset after a few seconds after
the overload -for examp le if a window is frozen -has been remedied .
No. Equipment
1 Parking br ake
2 A ir cond ition ing
3 Shift gate
4 Vacan t
5
6
7
---· 8
Eng ine contro l
Oxygen sensor before the three-way
cat alytic converter
Oxygen sensor behind the three -way
catalytic converte r
E ngine control, auxiliary w ater pump
Amps
5
10
5
15
15
15
1 0

________________________________________________ F_ u_s _e_ s_ a_ n_ d_ b_u_ lb_ s _ __.lftll
No. Equipment
9
10
11
13
14
15
16
17
Climate control front/rear, dash panel buttons
Suspension level control system
(Adaptive Air Suspension)
Light and rain sensor
Display-/control unit
Roof electronics control unit
CD/DVD drive Energy management
Vacant
Radiator fan electronics
Airbag front passenger recognition (weight sensor)
19 Vacant
20 Heated/ventilated seats
21 Engine control module
22 Vacant
23 Parking brake (switch)
24 Vehicle electrical system
25
26 Automat
ic transm ission
Air conditioning water valves water pump, rear climate control
27 Sunroof
28 Engine control module
29 Fuel injectors
30 Ignition coils
31 Fuel pump, r ight/fuel pump e lectron ics
Amps
5
10
5
5
10
5
5
5
5
5
5
5
10
15
10
20
5
15
30
20/40
-
Vehicle OP-eration
No ... Equipment
32
33
34
35
36
39
40
41
Automatic transmission
Right rear foo twell heater
Heated/ventilated seats, rear
Heated/venti lated seats, front
Cigarette lighter, front
Cigarette lighter, rear/socket, rear
Auxiliary cooler fan Door cont rol un it, front r ight
Brake booster
Door control un it, rear right
42 Vacant
43 Headlight washer system
Air conditioning heater fan
Amps
5
25
20
20
20
20/25
20
7.5
15
7.5
30
30
•
Fuse Location , Luggage Compartment left
0
Fig . 28 0 Fuse pan el
l a yo ut ..
Vehicle care Do-it-yourself service iTechnical data

lffll.,___F_ u_ s_e _ s_ a_n_ d_ b_u _ l_ b_s _______________________________________________ _
No.
1
2
3
4
5
6
7
8
9
10
Equipment
Vacant
Vacant
Vacant
Vacant
Digita l sound system control module
Navigation
TV Tuner
Rear-view camera
Commun ications box
Subwoofer in rear window shelf (BOSE)/
Amplifier (Bang
& Olufsen)
11 Socket
12 Vacant
Amps
30
5
10
5
5
15/30
20
Fuse Location, Luggage Compartment
right
Fig. 281 Fuse panel
layout
•
No. Equipment
1 Vacant
2 Fuel pump, left
3 Vacant
4 Vacant
5
6
7
8
9
Central control module for comfort system
(left light)
Central control module for comfort system (right light)
Central control module for comfort system (door clos ing)
Electronic parking brake control module, left
Electronic parking brake control module, right
10 Vacant
11 Vacant
12 Vacant
Bulbs
Replacing light bulbs
Amps
20
20
-
10
20
30
30
For your safety, we recommend that you hove your autho ­
rized Audi dealer replace burned out bulbs for you.
It is becoming increasingly more and more difficult to replace veh icle
light bu lbs since in many cases, other parts of the car must first be
removed before you are able to get to the bulb. This applies especially
to the light bulbs in the front of your car which you can only reach
through the engine compartment.
•
Sheet metal and bu lb holders can have sharp edges that can cause
serious cuts, and parts must be correctly taken apart and then prop- .,

_______________________________________________ F_u _s_ e_ s_ a_ n_ d_ b_u _ l_ b _ s __ lllll
erly put back together to he lp prevent breakage of parts and long
t erm d am ag e fro m wat er th at can enter housin gs th at h ave not been
properly resealed.
For your safety, we recommend that you have your a uthorized Audi
de aler repla ce a ny bu lbs for you, s ince your deale r has the prope r
too ls, t he correct bu lbs and t he expertise.
Ga s discharge lamp s (Xenon lights) :
Due to the high electrical voltage, have the bulbs replaced by a qual­
ifie d technician. Headlig hts with Xe non light can be identified by the
hig h volt age sticker.
& WARNING
Contact with high-voltage components of the electrical system
and improper replacement of gas discharge (Xenon ) headlight
bulbs can cause serious personal injury and death .
• Xenon bulb s are pres surized and can explode when being
changed.
• Changing Xenon lamp s requires the special training, instruc ­
tions and equipment .
• Only an authorized Audi dealer or other qualified workshop
should change the bulbs in gas discharge lamps .
& WARNING
There are parts with sharp edges on the openings and on the bulb
holders that can cause serious cuts .
• If you are uncertain about what to do , have the work
performed by an authorized Audi dealer or other qualified work­
shop. Serious personal injury may result from improperly
performed work.
Safety first
(I] Tips
• If you mus t repl ace the light bulbs yourse lf , a lways remember
that the eng ine compartme nt of any vehicle is a hazar do us area to
work in. Always read and hee d all WA RNING S=>
page 281, "E ngi ne
compartment" =>& .
• It is bes t to ask yo ur author ized Audi dealer wheneve r yo u need to
change a bulb.•
Vehicle care Do-it-yourself service Technical data

111.___E_ m_ e_ r-' g=- e_n_ c=-y _ s_it _ u _ a_t_ i_ o _ n_ s ______________________________________________ _
Emergency situations
General
This section is intended for trained emergency crews and personnel
who have the necessary tools and equipment to perform these
operations. •
Starting by pushing or towing
0 Note
Your vehicle is equipped with an automatic t ransmission . Conse­
quently, the e ngine ca nnot be started by push ing or tow ing .•
Starting with jumper cables
I f necess ary, the engine can be started b y connectin g it to
t he bat tery of another vehicle.
If the e ng ine shou ld fa il to start because of a discharged or weak
battery, the batte ry can be connected to t he battery of
another
veh icle, us ing a pair of jumper cables to start the eng ine .
Jumper cables
Use only jumper cables of suffic iently large cross section to carry the
sta rter cur rent s afely . Refer to the m an ufa ct ur er's specificat ions.
Use only j umpe r cab les with
insulated te rmi nal clamps wh ich are
distinct ly marked :
plu s(+) cable i n most cases colored red
minus (-) cable i n most cases colored black .
& WARNING
Batterie s contain el ectricity, acid, and gas . Any of the se can cause
very serious or fatal injury. Follow the inst ructions below for safe
handling of your vehicle 's battery.
• Always shield your eyes and avoid leaning over the battery
whenev er po ssible .
• A discharged battery can freeze at temperatures just below
32 °F (0 °C ). Before connecting a jumper cable, you must thaw the
frozen battery completely, otherwise it could explode.
• Do not allow battery acid to contact eyes or sk in . Flush any
contacted area with water immedi ately .
• Improper use of a booste r battery to start a vehicle may cause
an explosion .
• Vehicle batteries generate e xplosive gases. Keep sparks, flame
and lighted cigarettes away from batterie s.
• Do not try to jump start any vehicle with a low acid level in the
battery.
• The voltage of the booster battery must also have a 12-Volt
rating. The capacity (Ah) of the booster battery should not be
lower than that of the discharged battery . Use of batteries of
different voltage or substantially different "Ah " rating may cau se
an e xplosion and personal injury.
• Never charge a frozen battery . Gas trapped in the ice may cause
an explosion.
• Never charge or use a battery that has been frozen. The battery
c ase may have be weakened .
• Use of batteries of different voltage or substantially different
capacity (Ah) rating may cause an explosion and injury . The
capacity (Ah) of the booster battery should not be lower than that
of the discharged battery. .,_

_____________________________________________ E_ m___;, e_r-=g ~ e_ n_c,_:!y:.__: s_i:..:t ..:..u :..:a;;,. t.:.; i...: o :..: n...:..:. s _ __,J_
& WARN ING (conti nued)
• Before you check anything in the engine compartment , always
read and heed all WARNINGS~
page 281, "Engine compart­
ment ".
0 Note
• App lying a higher vo ltage booster battery will cause expensive
damage to sens itive e lectron ic components, such as contro l units,
relays, radio, etc.
• There must be no electrical contact between the vehicles as other­
wise current could already start to flow as soon as the positive(+)
terminals are connected.
[I] Tips
• The discharged battery must be properly connected to the
vehicle's electrical system . When jump starting or charging the
battery, never connect the negative ground cable to the battery nega­
tive post because the battery manager system must be able to detect
the battery's state of charge . Always connect the negative ground
cable to the negative ground post of the battery manager control
unit. •
Vehicle OP-eration
Use of jumper cables
Make sure to connect the jumper cable clamps in exactly
the order described below!
Fig. 282 Jump
starting with the
battery of another
vehicle: A -discharged
vehicle battery, B -
booster battery
The procedure described below for connecting jumper cables
is intended to provide a jump start for your vehicle.
Vehicle with discharged battery:
- Turn off lights and accessories, move lever of automatic
transmission to
N (Neutral) or P (Park) and set parking
brake.
Connect POSITIVE(+) to POSITIVE(+) (red)
1. Connect one end to the positive terminal~ fig. 282 © of
your battery @.
2 . Connect the other end to the positive terminal @ of the
booster battery®·
Connect NEGATIVE(-) to NEGATIVE(-)
(black)
3. Connect one end to the negative terminal® of the
booster battery@.
Vehicle care Do-it-yourself service iTechnical data

llffl.___E_ m_ e_r-= g=- e_ n_c-= y'-- s_ i_t _u _a_ t_ i_ o _ n_ s ____________________________________________ _
4. C onn ect the ot her end to the negative ground post of the
battery manager control unit located nex t to the battery .
Starting the engine
-Start the engine o f th e vehicle with the booster battery .
Ru n the engine at a mode rate speed.
- Start engine with discharged vehic le battery in the usua l
manner.
- If the e ngine fai ls to star t: do no t keep the s tarter
crank ing for longer than 10 seconds . Wait for about 30
seconds a nd then try aga in.
- With eng ine runni ng, remove jumper cables from bot h
veh icles in t he exact
reverse order.
T he b att ery is ven ted to the outside to p reve nt gases from en ter ing
the vehicle interior. Make sure that the jumper clamps are well connected wi th their
metal parts in full contact with the battery
terminals.
& WARNING
To avoid serious personal injury and damage to the vehicle, heed
all warnings and in stru ction s of the jumper cable manufa cturer . If
in doubt , call for road service.
• Jumper cable s mu st be long enough so that the vehicle s do not
touch.
• Wh en connecting jumper cables, make sure that they cannot
get caught in any moving part s in the engine compa rtment.
• Before you check anything in the engine compartment, always
read and heed all WARNINGS~
page 281, "Engine compart­
ment ".
0 Note
Improper hook-up of jumpe r cables can ruin the generator.
• Always connect POS ITIVE(+) to POS ITIVE(+), and NEGA TIVE(-)
to NEGATIVE (-) ground post of the battery manager co ntrol unit .
• Check t hat all s crew p lugs on t he b attery cells are screwed in
firm ly . If not, tighten plugs pr ior to co nnecting clamp on negative
battery terminal.
• Please note that the procedure for connecting a jumper cable as
descr ibed above appli es specifically to the case o f yo ur vehi cle be in g
jump started. W hen you are giving a jump sta rt to another vehicle, do
not connect the negative (-) cab le to t he negative ( -) termina l on the
discharged battery©~
page 349, fig. 282 . Instead, securely
connect the negative(-) cable to either a solid metal component that
is firmly bolted to t he eng ine b lock o r to the eng ine b lock itself. If the
battery that is being charged does not vent to the outside, escap ing
b attery gas could ignite and exp lode! •
Emergency towing with
commercial tow truck
General hints
Your Audi requires special handling for towing.
Th e fo llow ing in forma tion is to be used by commerci al tow tru ck
operators who know how to operate their equ ipment safely .
• Never to w your Aud i, towing will cause damage to the eng ine
and tran smi ssion .
• Neve r wrap the safety chains or winch cable s around the b rake
lines.
• To prevent unnece ssary damage, your Audi must be transported
with a flat bed truck . _.,