2009 SUBARU TRIBECA monitor

LAN(diag)-23
Subaru Select Monitor
LAN SYSTEM (DIAGNOSTICS)
5) After setting, make sure that vehicle equipment is same as the setting changed in the {Current Data Dis-
play & Save}.
CAUTION:
•It is possible to control the original functions of vehicle when settings above are corresponded to
vehicle equipment.
•Do not change the settings except for setting above during operation of equipment setting.
•Be sure not to change Factory initial setting except installation of new body integrated unit.
NOTE:
For details concerning operation procedure, refer to the “SUBARU SELECT MONITOR OPERATION MANUAL”.
Hazard answer-
back setupON
ON
Workable when hazard answer-back setup is set to “ON.”
When lock/unlock is selected by keyless entry system
operated, hazard answer-back buzzer operates.

OFFWhen lock/unlock is selected by keyless entry system
operated, hazard answer-back does not operate.
Automatic lock-
ing setupONONWorkable when Automatic locking setup is set to “ON”
Automatic locking operates.Not supported by North
American specificationsOFF Automatic locking does not operate.
Ans.-back
BuzzerON
ONVe h i c l e i s c o n t r o l l e d i n a n sw e r - b a c k b u z z e r e q u i p p e d
mode.Not supported by North
American specificationsOFF
Ve h i c l e i s c o n t r o l l e d i n a n sw e r - b a c k b u z z e r n o n - e q u i p p e d
mode. (Set Ans.-back Buzzer to “OFF” in model without
answer back buzzer.)
Auto locking ON
ON Vehicle is controlled in auto locking equipped mode.Not supported by North
American specificationsOFFVe h i c l e i s c o n t r o l l e d i n a u t o l o c k i n g n o n - e q u i p p e d m o d e .
(Set Auto locking to “OFF” in model without auto locking.)
Initial Keyless
Setting—
——
Execution
Settings of keyless entry system are initialized. (Auto-lock
time: 30 sec., Answer-back buzzer setup: ON, Hazard
answer-back setup: ON, Automatic locking setup: ON,
Ans.-back Buzzer: ON)
Initial button set-
ting—
——
Execution
Settings of each function are initialized. (Off delay time:
Normal, Rr defogger op. mode: 15 min., Wiper deicer op.
mode: 15 min., Lockout prevention: ON)
Initial Security
setting—
——
Not supported by North
American specificationsExecution
Settings of security system are initialized. (Security Alarm
Setup: OFF, Impact Sensor Setup: OFF, Alarm monitor
delay setting: ON, Siren setting: OFF)
Passive Alar m
(Not used)OFFONWorkable when passive ar ming is set to “ON.”
OFF
Door open
warning (pre-
vention of bat-
tery run-out)
OFF
ON
If detecting door open for 30 minutes, room light, key illu-
mination and door warning light are turned off to prevent
battery run-out.

OFFRoom light, key illumination and door warning light is not
turned off.
Alarm inter-
locked room
light switch
OFF
ONThe room light lights by being interlocked with the activa-
tion of the alarm.

OFFRoom light does not illuminate even if the alarm is acti-
vated.
DataInitial set-
ting value
Customize
settingRemarksDestination
Specifications

LAN(diag)-24
Subaru Select Monitor
LAN SYSTEM (DIAGNOSTICS)
10.FUNCTION CHECK
In order to check the body integrated unit function,
inspect the body integrated unit and actuator using
Subaru Select Monitor without operating switches.
1) On the «Main Menu» display screen, select the
{Each System Check} and press the [YES] key.
2) On the «System Selection Menu» display
screen, select the {Integ. Unit mode} and press the
[YES] key.
3) On the «Integ. Unit mode failure diag» display
screen, select the {Function Check} and press the
[YES] key.
4) Select the item to be operated on the «Function
Check» display screen with «UP/Down key» and
press the [YES] key.
5) Pressing [YES] starts, [NO] cancels the opera-
tion and [YES] returns to the System Operation
Check Mode display screen.
NOTE:
If not equipped (based on area or condition), pro-
cess will not go on.

LAN(diag)-25
Read Diagnostic Trouble Code (DTC)
LAN SYSTEM (DIAGNOSTICS)
7. Read Diagnostic Trouble
Code (DTC)
A: OPERATION
For details concerning DTC reading procedure, re-
fer to “Subaru Select Monitor”. 12, READ DIAGNOSTIC TROUBLE CODE (DTC),
OPERATION, Subaru Select Monitor.>

LAN(diag)-26
Clear Memory Mode
LAN SYSTEM (DIAGNOSTICS)
8. Clear Memory Mode
A: OPERATION
For details concerning DTC clear operation, refer to
“Subaru Select Monitor”. CLEAR MEMORY MODE, OPERATION, Subaru
Select Monitor.>

LAN(diag)-27
Read Current Data
LAN SYSTEM (DIAGNOSTICS)
9. Read Current Data
A: OPERATION
1) On the «Main Menu» display screen, select the
{Each System Check} and press the [YES] key.
2) On the «System Selection Menu» display
screen, select the {Integ. Unit mode} and press the
[YES] key.
3) On the «Integ. unit mode failure diag» display
screen, select the {Current Data Display & Save}
and press the [YES] key.
4) On the «Data Display Menu» screen, select the
{12 Data Display} and press the [YES] key.
5) Using the scroll key, scroll the display screen up
or down until the desired data is shown.
TA, OPERATION, Subaru Select Monitor.> to LAN(diag)-14, DISPLAY OF ON/OFF DATA,
OPERATION, Subaru Select Monitor.> LAN(diag)-18, CONFIRMATION OF CURRENT
SETTING, OPERATION, Subaru Select Monitor.>

LAN(diag)-28
Function Setting (Customize)
LAN SYSTEM (DIAGNOSTICS)
10.Function Setting (Customize)
A: OPERATION
For detailed procedures of function setting (ECM
customizing), refer to “SUBARU SELECT MONI-
TOR”. TING (ECM CUSTOMIZING), OPERATION,
Subaru Select Monitor.>

LAN(diag)-29
List of Diagnostic Trouble Code (DTC)
LAN SYSTEM (DIAGNOSTICS)
11.List of Diagnostic Trouble Code (DTC)
A: LIST
DTC Item Content of diagnosis Note
None Communication for initializing
impossible
Open or short in Subaru
Select Monitor communi-
cation line
INITIALIZING IMPOSSIBLE, Diagnostic Proce-
dure with Diagnostic Trouble Code (DTC).>
None Diagnostic trouble code (DTC) is
not stored
Internal error of combina-
tion meter
CODE (DTC) IS NOT STORED, Diagnostic Proce-
dure with Diagnostic Trouble Code (DTC).>
B0100 Integ. unit system error Body integrated unit inter-
nal error
SYSTEM ERROR, Diagnostic Procedure with
Diagnostic Trouble Code (DTC).>
B0101 BATT power supply (Control)
error
Open or short in battery
power supply control cir-
cuit
PLY MALFUNCTION CONT., Diagnostic Proce-
dure with Diagnostic Trouble Code (DTC).>
B0102 BATT p/supply malfunction cont. Open or short of battery
power supply backup cir-
cuit
PLY MALFUNCTION CONT., Diagnostic Proce-
dure with Diagnostic Trouble Code (DTC).>
B0103 Ignition power failure Open or short in IGN
power supply circuit
POWER FAILURE, Diagnostic Procedure with
Diagnostic Trouble Code (DTC).>
B0104 ACC power failure Open or short in ACC
power supply circuit
FA I L U R E , D i a g n o s t i c P r o c e d u r e w i t h D i a g n o s t i c
Tr o u b l e C o d e ( D T C ) . >
B0106 Shift lock circuit failure Ground short of shift lock
circuit
CIRCUIT FAILURE, Diagnostic Procedure with
Diagnostic Trouble Code (DTC).>
B0201 CAN-HS counter abnormal Malfunction of high-speed
CAN communication
COUNTER ABNORMAL, Diagnostic Procedure
with Diagnostic Trouble Code (DTC).>
B0202 CAN-HS bus off Any unit is cut communi-
cation.
OFF, Diagnostic Procedure with Diagnostic Trou-
ble Code (DTC).>
B0211 CAN-HS ECM data abnormal Received error data from
ECM.
DATA ABNORMAL, Diagnostic Procedure with
Diagnostic Trouble Code (DTC).>
B0212 CAN-HS TCM data abnormal Received error data from
TCM.
DATA ABNORMAL, Diagnostic Procedure with
Diagnostic Trouble Code (DTC).>
B0213 CAN-HS VDC/ABS data abnor-
mal
Received error data from
VDC/ABS unit.
ABS DATA ABNORMAL, Diagnostic Procedure
with Diagnostic Trouble Code (DTC).>
B0221 CAN-HS ECM no-receive data Not received error data
from ECM.
NO-RECEIVE DATA, Diagnostic Procedure with
Diagnostic Trouble Code (DTC).>
B0222 CAN-HS TCM no-receive data Not received error data
from TCM.
NO-RECEIVE DATA, Diagnostic Procedure with
Diagnostic Trouble Code (DTC).>
B0223 CAN-HS VDC/ABS no-receive
data
Not received error data
from VDC/ABS unit.
ABS NO-RECEIVE DATA, Diagnostic Procedure
with Diagnostic Trouble Code (DTC).>
B0300 CAN-LS malfunction Open or short in CAN-LS
circuit, on each side or
both sides.
FUNCTION, Diagnostic Procedure with Diagnos-
tic Trouble Code (DTC).>
B0301 CAN-LS counter abnormal Malfunction of CAN-LS
communication
COUNTER ABNORMAL, Diagnostic Procedure
with Diagnostic Trouble Code (DTC).>

LAN(diag)-30
List of Diagnostic Trouble Code (DTC)
LAN SYSTEM (DIAGNOSTICS)
B0302 CAN-LS bus off Any unit is cut communi-
cation.
OFF, Diagnostic Procedure with Diagnostic Trou-
ble Code (DTC).>
B0311 CAN-LS meter unit data abnor-
mal
Received error data from
meter.
METER UNIT DATA ABNORMAL, Diagnostic Pro-
cedure with Diagnostic Trouble Code (DTC).>
B0313 CAN-LS monitor data abnormal Received error data from
monitor.
MONITOR DATA ABNORMAL, Diagnostic Proce-
dure with Diagnostic Trouble Code (DTC).>
B0321 CAN-LS meter no-receive data Not received error data
from meter.
METER NO-RECEIVE DATA, Diagnostic Proce-
dure with Diagnostic Trouble Code (DTC).>
B0401 M collation NG Malfunction related immo-
bilizer
Code (DTC).>
B0402 Immobilizer Key collation NG Malfunction related immo-
bilizer
Code (DTC).>
B0403 E/G request NG Malfunction related immo-
bilizer
Code (DTC).>
B0500 Keyless UART com. malfunction Open or short circuit in
keyless UART circuit
UART COM. MALFUNCTION, Diagnostic Proce-
dure with Diagnostic Trouble Code (DTC).>
DTC Item Content of diagnosis Note