2009 SUBARU TRIBECA lock

SL-54
Immobilizer Control Unit
SECURITY AND LOCKS
25.Immobilizer Control Unit
A: NOTE
The control of immobilizer system is carried out in
body integrated unit.
B: REMOVAL

C: INSTALLATION
Install in the reverse order of removal.

SL-55
Immobilizer Antenna
SECURITY AND LOCKS
26.Immobilizer Antenna
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the screws, and detach the upper col-
umn cover and lower column cover.
3) Remove the instrument panel lower cover. to EI-36, REMOVAL, Instrument Panel Lower Cov-
er.>
4) Disconnect the immobilizer antenna connector
(A) and ignition switch lighting connector (B).
5) Loosen the screw and release the lock (D) at op-
posite side using flat-tip screwdriver (1), and then
detach the immobilizer antenna (C).
CAUTION:
Do not apply excessive force to remove the im-
mobilizer antenna and lock. Otherwise they
may be broken because those parts are the
products made of a plastic.
B: INSTALLATION
Install in the reverse order of removal.
SL-00258
(D)
(1)
SL-00315
(A)
(C)
(B)

SL-56
Immobilizer Antenna
SECURITY AND LOCKS

SR-5
Glass Lid
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
3. Glass Lid
A: REMOVAL
1) Completely close the glass lid, and then open
the sunshade.
2) Remove the cover (A), and then remove the
TORX® bolts (B).
CAUTION:
The thread locker is applied to the TORX® b o l t s ,
so use the new parts once they are removed.
3) Remove the glass lid carefully.
B: INSTALLATION
Install in the reverse order of removal.
C: ADJUSTMENT
Loosen the glass lid mounting TORX® bolts (A),
and then adjust the height with moving the lid.
Difference in height between glass lid and roof
panel L:
2.0±1.0 mm (0.079 ± 0.039 in)
(A)
(B)
SR-00091
(A)
SR-00117
L

WW-4
General Description
WIPER AND WASHER SYSTEMS
3. WASHER TANK
C: CAUTION
•Connect the connectors and hoses securely during reassembly.
•After reassembly, make sure functional parts operate smoothly.
•Be careful with the airbag system wire harness which passes near electrical parts and switches.
•All airbag system wiring harness and connectors are colored yellow. Do not use a tester equipment on
these circuits.
•Care must be taken when connecting the hoses to pipes so that there are no bends or blockage.
•If even a small amount of silicon oil or grease enters tank and washer fluid passages, an oil film will be
formed on the glass and will cause the wiper to chatter and judder. Make sure that no oil comes into contact
with the system.
(1) Washer nozzle (5) Front washer motorTightening torque: N·m (kgf-m, ft-lb)
(2) Washer hose (6) Rear washer motorT: 6.0 (0.61, 4.4)
(3) Washer tank (7) Grommet
(4) Washer tank cap (8) Washer motor cover

WW-10
Wiper Blade
WIPER AND WASHER SYSTEMS
4. Wiper Blade
A: REMOVAL
CAUTION:
When replacing the wiper blade, if standing up
the wiper arm, be sure to stand up the driver’s
side wiper arm first, and then passenger’s side
wiper arm next. Also, when putting the wiper
arms back, be sure to start with passenger’s
side first, then driver’s side next. Doing this in
the reverse order may result in the driver’s side
wiper blade hitting the passenger’s side wiper
arm and causing damage.
1. FRONT
While pushing the locking clip to the direction of the
arrow, pull out and remove the blade from the arm.
2. REAR
Turn the blade in the direction of arrow (A) and re-
move it from arm.
B: INSTALLATION
1) Install in the reverse order of removal.
2) Confirm that the clip is locked securely.
C: DISASSEMBLY
1. FRONT
Pull side (A) of the wiper rubber stopper and re-
move the rubber from the blade assembly.
2. REAR
Pull the wiper rubber top slightly from stopper (A)
and pull out completely.
WW-00354
(A) Turn the wiper blade.
(1) Wiper arm
(2) Wiper blade
(3) Wiper blade attachment section
(1)
(2)
(3)(A)WW-00207
WW-00009
WW-00143
(A)

BR-4
General Description
BRAKE
B: COMPONENT
1. FRONT DISK BRAKE
(1) Caliper body (9) Support (16) Disc cover
(2) Air bleeder screw (10) Pad clip (17) Bushing
(3) Guide pin (Green) (11) Outer shim
(4) Pin boot (12) Inner shimTightening torque: N·m (kgf-m, ft-lb)
(5) Piston seal (13) Pad (Outside)T1: 8 (0.8, 5.8)
(6) Piston (14) Pad (Inside)T2: 27 (2.8, 19.9)
(7) Piston boot (15) Disc rotorT3: 120 (12.2, 88.5)
(8) Lock pin (Yellow)
BR-00490
(1)
(2)
(3)
(4)
(4)
(17)(10)
(16)
(15)
(5)
(6)(7)
(8)
T2
T3
(11)
(11)
(12)
(12)
(13)
(14)
(13)
T1
(9)

BR-5
General Description
BRAKE
2. REAR DISC BRAKE
(1) Caliper body (13) Outer pad (25) Secondary shoe return spring
(2) Air bleeder screw (14) Shim (26) Primary shoe return spring
(3) Guide pin (Green) (15) Shoe hold pin (27) Adjusting spring
(4) Pin boot (16) Cover (28) Adjuster
(5) Piston seal (17) Back plate (29) Brake shoe cup
(6) Piston (18) Retainer (30) Brake shoe spring
(7) Piston boot (19) Spring washer
(8) Support (20) Parking brake leverTightening torque: N·m (kgf-m, ft-lb)
(9) Lock pin (Yellow) (21) Parking brake shoe (Secondary)T1: 8 (0.8, 5.8)
(10) Bushing (22) Parking brake shoe (Primary)T2: 27 (2.8, 19.9)
(11) Pad clip (23) StrutT3: 37 (3.7, 27.2)
(12) Inner pad (24) Strut shoe springT4: 66 (6.7, 48.7)