2009 RENAULT TWINGO Mechanism And Accessories Workshop Manual

55A-19
EXTERIOR PROTECTION
Front wheel arch liner: Removal - Refitting
55A
REFITTING
I - REFITTING PREPARATIONS OPERATION
aCheck the condition of the clips and replace them if
necessary.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the front wheel arch liner starting at the rear sec-
tion,
-the clips (1) ,
-the bolts (2) and (3) .
III - FINAL OPERATION.
aRefit the front wheels (see Wheel: Removal - Refit-
ting) (MR 411, 35A, Wheels and tyres).

56A-1
EXTERIOR EQUIPMENT
Scuttle panel grille: Removal - Refitting
56A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the wiper arms from the windscreen wiper
(see Windscreen wiper arm: Removal - Refitting)
(MR 411 Mechanical, 85A, Wiping - Washing).
aRemove the seal (1) .
aUnclip the windscreen lower trims (2) .II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove:
-the bolts (3) ,
-the clips (4) .
aRemove the scuttle panel grille (5) and (6) .
119268
119269
119270

56A-2
EXTERIOR EQUIPMENT
Scuttle panel grille: Removal - Refitting
56A
REFITTING
I - REFITTING PREPARATIONS OPERATION
aAlways replace:
-the clips under the scuttle panel grille,
-the foam strips which ensure the scuttle panel grille
sealing.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the scuttle panel grille,
-the clips (4) ,
-the bolts (3)
III - FINAL OPERATION.
aClip on the windscreen lower trims (2) .
aRefit:
-the seal (1) ,
-the windscreen wiper arms (see Windscreen wi-
per arm: Removal - Refitting) (MR 411 Mechani-
cal, 85A, Wiping - Washing).Note:
Check the condition and cleanliness of the
windscreen and scuttle panel grille before refit-
ting the scuttle panel grille.

56A-3
EXTERIOR EQUIPMENT
Tailgate spoiler: Removal - Refitting
C44
56A
REMOVAL
OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the blanking covers (1) ,
-the bolts (2) .
aRemove the tailgate spoiler (3) .
REFITTING
REFITTING OPERATION FOR PART CONCERNED
aRefit:
-the tailgate spoiler (3) ,
-the bolts (2) ,
-the blanking covers (1) .
122852
122851

56A-4
EXTERIOR EQUIPMENT
Tailgate spoiler: Removal - Refitting
C44, and EQUIPMENT LEVEL SPORT
56A
REMOVAL
OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the blanking covers (1) ,
-the bolts (1) .
aUnclip the tailgate spoiler at (2) .
aCarefully detach the central section of the tailgate
spoiler.
aRemove the tailgate spoiler.
122852

56A-5
EXTERIOR EQUIPMENT
Tailgate spoiler: Removal - Refitting
C44, and EQUIPMENT LEVEL SPORT
56A
REFITTING
I - REFITTING PREPARATION OPERATION
aRemove any adhesive residue (3) with a rotary era-
ser (Part no.: 77 11 419 046 or 77 11 419 047).
aClean the bonding areas using a LINT-FREE
CLOTH soaked in HEPTANE (see Vehicle: Parts
and consumables for the repair) (04B, Consuma-
bles - Products) by pressing firmly and moving
slowly from back to front and in one direction only.
aWipe the bonding areas with a clean, dry LINT-
FREE CLOTH in one direction only.aAlways replace the DOUBLE-SIDED ADHESIVE
TAPE (see Vehicle: Parts and consumables for
the repair) (04B, Consumables - Products).
II - REFITTING OPERATION FOR PART
CONCERNED
aClip the tailgate spoiler.
aRefit:
-the bolts (1) ,
-the blanking covers (1) .
aRemove the protective backings from the double-si-
ded adhesive tape.
aBond the central section of the tailgate spoiler.
132044
132045
Note:
Chec k for any stains on the clean and dry lint-
free cloth. If any traces of stains are found,
resume the cleaning procedure.
Note:
To ensure good bonding of the double-sided
adhesiv e tape, apply continuous pressure using
the palm of the hand against a soft lint-free cloth.

56A-6
EXTERIOR EQUIPMENT
Scoop under the scuttle panel grille: Removal - Refitting56A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:
-the windscreen wiper arms (see Windscreen wi-
per arm: Removal - Refitting) (MR 411 Mechani-
cal, 85A, Wiping - Washing),
-the scuttle panel grille (see 56A, Exterior equip-
ment, Scuttle panel grille: Removal - Refitting,
page 56A-1) .
aRemove the cap on the shock absorber cup.
aRemove the shock absorber cup using the (1) , hol-
ding the shock absorber rod using the (2) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the bolts (3) .
aProtect the lower section of the windscreen using
masking tape.
121497
121498
121499

56A-7
EXTERIOR EQUIPMENT
Scoop under the scuttle panel grille: Removal - Refitting56A
aRemove the scoop under the scuttle panel grille (4) ,
(5) , (6) and (7) .
REFITTING
I - REFITTING PREPARATION OPERATION
a
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the scuttle panel grille scoop,
-the bolts (3) .
III - FINAL OPERATION.
aRefit the shock absorber cup using the (1) , holding
the shock absorber rod using the (2) .
aSeal the cap on the shock absorber cup using mas-
tic (part no.: 77 01 423 330).
aRefit:
-the cap on the shock absorber cup.
-the scuttle panel grille (see 56A, Exterior equip-
ment, Scuttle panel grille: Removal - Refitting,
page 56A-1) ,
-the windscreen wiper arms (see Windscreen wi-
per arm: Removal - Refitting) (MR 411 Mechani-
cal, 85A, Wiping - Washing).
121500
121501
121502
Note:
It is essential to replace the foam strips which
seal the scoop under the scuttle panel gr ille. The
foam strips are available from the Parts Depart-
ment.