2008 RENAULT SCENIC Passenger Comparment Connection Unit Workshop Manual

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-97
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-97V9 MR-372-J84-87B000$301.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF026
PRESENT
OR
STOREDPASSENGER SIDE REAR EXTERNAL AERIAL CIRCUIT
CO: Open circuit
NOTESConditions for applying the fault finding procedure to a stored fault:
Activation of command AC037: Transmitter aerial fault finding; if the fault becomes
present, then carry out this fault finding procedure.
Check that configuration CF097 Vehicle type has been correctly performed.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the condition and connection of the passenger's side rear door external aerial connector (tabs bent,
broken, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the PE3 connector of the UCH (tabs bent, broken, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connections:
●Connection code 26AL,
●Connection code 26AH.
Between components 645 and 1377.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF026 /UCH_V48_DF026/UCH_V4C_DF026/
UCH_V4D_DF026/UCH_V4F_DF026/UCH_V50_DF026

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-98
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-98V9 MR-372-J84-87B000$301.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF027
PRESENT
OR
STOREDEXTERNAL TEMPERATURE SENSOR CIRCUIT
CC.0: Short circuit to earth
CO.1: Short circuit or open circuit to + 12 V
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault reappears as stored following the fault being cleared.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check whether the passenger door mirror is fitted with a temperature sensor.
If NO, vehicle is not fitted with it; (if the vehicle is not fitted with an external temperature sensor, check that
configuration CF029 External temperature sensor has been correctly configured as WITHOUT.
If YES, perform the following fault finding procedure.
Check the temperature sensor connector (bent, oxidised, broken tabs).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the PE2 connector of the UCH (tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connections:
●Connection code 47C,
●Connection code 47D.
Between components 645 and 240.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF027 /UCH_V48_DF027/UCH_V4C_DF027/
UCH_V4D_DF027/UCH_V4F_DF027/UCH_V50_DF027

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-99
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-99V9 MR-372-J84-87B000$301.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF027
CONTINUED
Measure the resistance of component 240 (External temperature sensor) between the following connections:
●Connection code 47C,
●Connection code 47D.
Approximate temperature in ˚C Sensor resistance in Ω
between 0 and 5 between 5400 and 6200
between 11 and 15 between 3700 and 4400
between 21 and 25 between 2500 and 3000
between 31 and 35 between 1700 and 2100
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Replace the sensor if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -100
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -100V9 MR-372-J84-87B000$344.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
DF029
PRESENT
STEERING LOCK CIRCUIT
CC.1: Short circuit to + 12 V
1.DEF: Open circuit (e.g. lock disconnected) or lock power supply absent
2.DEF: Lock earth absent or multiplex network faulty (e.g. steering lock ΑΕ UCH
connection)
4.DEF: Short circuit to earth on the steering column lock sensor connection
5.DEF: Open circuit on the steering column lock sensor connection
6.DEF: Short circuit to + 12 V on the steering column lock sensor connection
NOTESSpecial note:
Attempt to apply forced + after ignition feed to update the faults.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
CC.1
NOTESAttempt to apply forced + after ignition feed to update the
faults.
Check the condition and connection of the steering column lock connector.
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of connectors PE2, PP2 on the UCH and connectors PEH (UPC Vdiag 44)
or CT1 (UPC Vdiag 48) on the UPC (bent or broken tabs, etc.).
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation and continuity of the following connections:
●Connection code 26I,
●Connection code 26AZ,
●Connection code 26BA, between the steering column lock (component code 1088) and the UCH
(component code 645)
●Connection code AP15, between the steering column lock (component code 1088) and the Protection and
Switching Unit (component code 1337)
If the connection(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF029P/UCH_V48_DF029P/UCH_V4C_DF029P/
UCH_V4D_DF029P/UCH_V4F_DF029P/UCH_V50_DF029P
MR-372-J84-87B000$344.mif

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -101
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -101V9 MR-372-J84-87B000$344.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF029
CONTINUED 1
1.DEF/
2.DEF
NOTESAttempt to apply forced + after ignition feed to update the
faults.
Check the presence and condition of fuses F5A and F5D on the Protection and Switching Unit ( Vdiag 44 UPC)
or fuses F11 and F18 ( Vdiag 48 UPC or later).
If the fuse(s) is faulty, replace it.
Check the condition and connection of the steering column lock connector.
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of connectors PP2 and PE2 on the UCH and connectors PEH (Vdiag44
UPC) or CT1 (Vdiag 48 UPC or later) on the Protection and Switching Unit (bent or broken tabs, etc.).
Ifthe connector(s) is faulty and if there is a repair procedure ( seeTe chnical Note 6 015A, Repairing e lectrical wiring,
Wiring: Precautions for repair), r epair the connector, otherwise replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code NAM between component 1088 and earth.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation and continuity of the following connections:
●Connection code 26I,
●Connection code 26AZ,
●Connection code 26BA.
Between components 645 and 1088.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on connection AP15 of component 1088.
Check the insulation, continuity and the absence of interference resistance on connection AP15 between
components 1337 and 1088.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the ignition on, check for + 12 V on connection APCB of component 645.
Check the insulation, continuity and the absence of interference resistance on connection APCB between
components 1337 and 645.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -102
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -102V9 MR-372-J84-87B000$344.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF029
CONTINUED 2
4DEF/
5.DEF/
6.DEF
NOTESAttempt to apply forced + after ignition feed to update the
faults.
Check the condition and connection of the steering column lock connector, component code 1088 (tabs bent,
broken, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the PE1 connector on the UCH, component code 645 (tabs bent, broken,
etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the continuity and the insulation of the following connection:
●Connection code 26J between components 645 and 1088.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -103
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -103V9 MR-372-J84-87B000$344.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF030
PRESENT
ANTI-LOCKING LINE
CO: Open circuit
NOTESUse Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
CO.1
NOTESNone.
Check the condition and connection of the steering column lock connector (tabs bent, broken).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the presence and condition of the F5D fuse on the UPC (Vdiag 44 UPC) or the F18 fuse (Vdiag 48 UPC
or later). Replace the fuse if it is faulty.
Check the condition and connection of connector PEH (UPC Vdiag 44) or connector CT1 (UPC Vdiag 48) of the
UPC (bent or broken tabs, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code AP15 between components 645 and 1088.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF030P/UCH_V48_DF030P/UCH_V4C_DF030P/
UCH_V4D_DF030P/UCH_V4F_DF030P/UCH_V50_DF030P

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -104
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -104V9 MR-372-J84-87B000$344.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF031
PRESENT
OR
STOREDONE TOUCH WINDOW CONNECTION
CC.1: Short circuit to + 12 V
CO.0: Open circuit or short circuit to earth
NOTESConditions for applying the fault finding procedure to a stored fault:
If the fault becomes present after a one-touch window has been activated, then apply
this fault finding procedure.
Special note: If the vehicle is not fitted with one-touch windows, ignore this fault. Refer
to the information about Electric windows in the Fault finding chart section.
If the vehicle has Mégane II ph2 bodywork: see MR 366 Fault finding, 87D, Electric
windows - Sunroof.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the condition and connection of the electric window connector (tabs bent, broken, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the connector PE2 of the UCH (tabs bent, broken, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 21K.
Between components:
–645 and 202,
–645 and 203,
–645 and 204,
–645 and 304.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF031 /UCH_V48_DF031/UCH_V4C_DF031/
UCH_V4D_DF03 1/UCH_V4F_DF031/UCH_V50_DF031