2008 RENAULT SCENIC clutch

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-28
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-28V9 MR-372-J84-87B000$086.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
1.3 SUB-FUNCTION: STARTING
The UCH manages the control section of the starting sub-function. For this function to operate normally, the
protection function must proceed correctly (immobiliser inactive ET046 Immobiliser).
In order to control the starter motor, the UCH requires the following status and parameter information to check that
the starting conditions have been met:
–Start button ET070 Start button.
–Clutch pedal position ET048 Clutch pedal position.
–Brake pedal position ET047 Brake pedal position.
–Automatic gearbox selector lever position ET108 Automatic gearbox selector lever position.
–Position of the manual gearbox selector lever (see 87G, Engine compartment connection unit, Conformity
check).
If the starting conditions are met, the request for the Protection and Switching Unit to activate the starter motor can
be viewed using status ET110 UCH request to injection or Protection and Switching Unit.
1.4 Main COMPONENTS of the ACCESS/SAFETY function
1.4.1 Main components of the ACCESS sub-function:
–Renault card,
–UCH,
–optical presence sensors located in the door handles,
–access aerials integrated in the door handles and the tailgate,
–the locking switches incorporated in the door handles,
–the boot-only opening/locking switch built into the boot badge,
–opening element locking motors.
1.4.1.1 The Renault card:
The Renault card has three buttons which allow:
–locking of the vehicle,
–unlocking of the vehicle,
–the boot to be locked/unlocked.
The Renault hands-free card allows hands-free operation if it is located in the access and starting zones.
The Renault card is powered by a 3 V battery. This battery is required for operation in hands-free mode or remote
control mode (card button presses).
If the battery is old or in an area of frequency interference, the emergency insert located in the Renault card allows
the driver's door to be unlocked.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-35
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-35V9 MR-372-J84-87B000$086.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
1.4.3 Main components of the STARTING sub-function:
The starting sub-function is based on the following main factors:
–The starting conditions being present.
–Passenger Compartment Control Unit (UCH).
–The automatic gearbox computer (if fitted on the vehicle).
–The Protection and Switching Unit.
1.4.3.1 Start button:
The start button transmits the driver's requests to start or stop the engine to the UCH.
1.4.3.2 The UCH:
The UCH ensures that the starting conditions are met, and that no other computer on the multiplex network is
inhibiting starting of the vehicle.
If the conditions are met, it requests control of the starter from the UPC.
1.4.3.3 The Protection and Switching Unit (UPC):
The Protection and Switching Unit activates the starter motor following a request from the UCH via the multiplex
network.
1.4.3.4 Neutral sensor (manual gearbox):
Informs the UCH of the position of the gearbox (neutral or gear engaged).
1.4.3.5 Clutch switch (manual gearbox):
Sends clutch pedal depressed signal (end of travel) to the UCH.
1.4.3.6 Brake switch:
Sends brake pedal depressed signal to the UCH.
Operation:
The unknown status does not automatically require the brake pedal to be replaced, because it is a temporary
operating status between released pedal status and depressed pedal status (see diagram above).

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault summary table
87B
87B-69
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault summary table
87B
87B-69V9 MR-372-J84-87B000$258.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault summary table
Tool fault Diagnostic tool title Vdiag
DF001UCH
44, 48, 4C, 4D, 4F, 50 DF002Steering lock
DF003Clutch switch circuit'
DF004Brake light switch circuit
DF005Card
DF006Front left-hand wheel valve sensor
DF007Front right-hand wheel valve sensor
DF008Rear right-hand wheel valve sensor
DF009Rear left-hand wheel valve sensor
DF010Steering column control unit circuit
DF011Rain/light sensor circuit
DF012Right-hand direction indicator circuit
DF013Left-hand direction indicator circuit
DF014Card reader circuit
DF015Optical sensor circuit
DF016At least 2 identical codes/summer set
DF017At least 2 identical codes/winter set
DF018Programming of 4 codes in summer set not performed
DF019Programming of 4 codes in winter set not performed
DF020Front internal aerial circuit
DF021Rear internal aerial circuit
DF022Centre internal aerial circuit
MR-372-J84-87B000$258.mif

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-75
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-75V9 MR-372-J84-87B000$301.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF003
PRESENT
OR
STOREDCLUTCH SWITCH CIRCUIT
CO.1: Short circuit or open circuit to + 12 V
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault appears after a road test at speed > 60 mph (100 km/h).
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
CO.1
NOTESNone.
Check the condition and connection of the clutch switch connector (tabs bent, broken, oxidised, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the PE1 connector of the UCH (tabs bent, broken, oxidised, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity against + 12 V of the following connection:
●Connection code 26X between components 645 and 675.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for an earth on connection MAM of component 675.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connection, otherwise replace the wiring.
If the connection is OK and earth is present, replace the clutch switch.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF003 /UCH_V48_DF003/UCH_V4C_DF003/
UCH_V4D_DF003/UCH_V4F_DF003/UCH_V50_DF003

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -125
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -125V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
KEYLESS VEHICLE FUNCTION
Sub:function: Starting
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
StartingET070:Start buttonDEPRESSED
RELEASED In the event of a fault,
consult the
interpretation of status
ET070.
ET108:Automatic gearbox
lever positionNOT IN NEUTRAL
P
NEUTRAL, REVERSEIn the event of a fault,
consult the
interpretation of status
ET108.
ET048:Clutch pedal
positionDEPRESSED
RELEASEDIn the event of a fault,
consult the
interpretation of status
ET048.
ET047:Brake pedal positionUNDETERMINED
RELEASED
DEPRESSED
INCONSISTENCY In the event of a fault,
consult the
interpretation of status
ET047.
ET110:UCH request to
injection or
Protection and
Switching UnitENGINE OFF
INACTIVE
APC
STARTING In the event of a fault,
consult the
interpretation of status
ET110.
ET169:EngineSTOPPEDIn the event of a fault,
refer to the
interpretation of
status ET169.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -140
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -140V9 MR-372-J84-87B000$430.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
*RAID: Renault Anti-Intruder Device
*CPE: Electric central door locking
*Lckg: Locking Tool status Diagnostic tool title Vdiag
ET041Opening rear screenV48, V4C, V4D,
V4F, V50
ET042Passenger door V44, V48, V4C,
V4D, V4F, V50
ET043RAID* function authorisation by CPE*
V44, V48, V4C,
V4D, V4F, V50 ET044CPE* button
ET045RF signal received
ET046Engine immobiliser
ET047Brake pedal position
ET048Clutch pedal position
ET050Tailgate/Boot
ET051Rear left-hand door
ET052Rear right-hand door
ET053Driver's door
ET054Optical sensors supplied
ET055Front driver side optical sensor
ET056Rear driver side optical sensor
ET057Passenger side front/rear optical sensor
ET058Lckg* button on driver's side handles
ET059Lckg* buttons on passenger's side handles
ET060Tailgate locking button
ET061Open tailgate request
ET062Open rear screen requestV48, V4C, V4D,
V4F, V50

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -170
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -170V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET048
CLUTCH PEDAL POSITION
NOTESThere must be no present or stored faults.
Special note:
Switch on forced after ignition.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
ET048 Released with the pedal depressed.
Check the connection and condition of the connector for the clutch pedal switch.
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Remove the clutch pedal switch and check for earth on connection MAN of component 675.
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the continuity of the following connections:
●Connection code 26X,
●Connection code MAN of component 675 (Brake pedal switch in pedal depressed position).
Only replace the clutch pedal switch if it is not correct.
Check the condition and connection of connector PE1 on the UCH.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 26X between components 645 and 675.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET048/UCH_V48_ET048/ UCH_V4C_ET048/
UCH_V4D_ET048 /UCH_V4F_ET048/UCH_V50_ET048

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -171
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -171V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET048
CONTINUED
ET048 Depressed without depressing the pedal.
Check the condition and connection of the clutch pedal switch connector.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Remove the clutch pedal switch and check the insulation between the following connections:
●Connection code 26X,
●Connection code MAN of component 675 (Brake pedal switch in pedal released position).
Only replace the clutch pedal switch if it is not correct.
Check the condition and connection of connector PE1 on the UCH
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 26X. Between components 645 and 675.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.