2008 NISSAN TEANA headlamp

FRONT COMBINATION LAMP
EXL-343
< ON-VEHICLE REPAIR >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
ON-VEHICLE REPAIR
FRONT COMBINATION LAMP
Exploded ViewINFOID:0000000003773730
REMOVAL
DISASSEMBLY
Removal and InstallationINFOID:0000000003773731
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
1. Front combination lamp
JPLIA1087ZZ
1. Front turn signal lamp bulb 2. Front turn signal lamp bulb socket 3. Halogen bulb (HI)
4. Seal packing 5. Resin cap 6. Halogen bulb (LO)
7. Parking lamp bulb socket 8. Parking lamp bulb 9. Headlamp housing assembly
JPLIA1105ZZ

EXL-344
< ON-VEHICLE REPAIR >[HALOGEN TYPE]
FRONT COMBINATION LAMP
1. Remove the front bumper fascia. Refer to EXT-11, "Exploded View".
2. Remove the headlamp mounting bolts.
3. Remove the harness clips from the headlamp housing.
4. Pull out the headlamp assembly forward the vehicle.
5. Disconnect the connector before removing the headlamp assembly.
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to EXL-336, "
Description".
ReplacementINFOID:0000000003773732
CAUTION:
 Disconnect the battery negative terminal or remove the fuse.
 After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
 Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
 Never touch bulb by hand while it is lit or right after being turned off.
 Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB (LO)
1. Remove the fender protector. Keep a service area. Refer to EXT-22, "FENDER PROTECTOR : Exploded
View".
2. Rotate the resin cap counterclockwise and unlock it.
3. Disconnect the headlamp bulb (LO) connector.
4. Rotate the bulb counterclockwise and unlock it.
5. Remove the bulb from the headlamp housing.
HEADLAMP BULB (HI)
1. Remove the fender protector. Keep a service area. Refer to EXT-22, "FENDER PROTECTOR : Exploded
View".
2. Disconnect the headlamp bulb (HI) connector.
3. Rotate the bulb counterclockwise and unlock it.
4. Remove the bulb from the headlamp housing.
PARKING LAMP BULB
1. Remove the fender protector. Keep a service area. Refer to EXT-22, "FENDER PROTECTOR : Exploded
View".
2. Rotate the parking lamp bulb socket counterclockwise and unlock it.
3. Remove the bulb from the parking lamp bulb socket.
FRONT TURN SIGNAL LAMP BULB
1. Remove the relay box cover*. Refer to PCS-34, "Exploded View".
*: When replace a left
2. Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
3. Remove the bulb from the front turn signal lamp bulb socket.
Disassembly and AssemblyINFOID:0000000003773733
DISASSEMBLY
1. Rotate the resin cap counterclockwise and unlock it
2. Disconnect the headlamp bulb (LO) connector.
3. Rotate the headlamp bulb (LO) counterclockwise and unlock it
4. Remove the bulb from the headlamp housing.
5. Rotate the headlamp bulb (HI) counterclockwise and unlock it

FRONT COMBINATION LAMP
EXL-345
< ON-VEHICLE REPAIR >[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
6. Remove the bulb from the headlamp housing.
7. Rotate the parking lamp bulb socket counterclockwise and unlock it.
8. Remove the bulb from the parking lamp bulb socket.
9. Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
10. Remove the bulb from the front turn signal lamp bulb socket.
ASSEMBLY
Assemble in the reverse order of disassembly.

EXL-350
< ON-VEHICLE REPAIR >[HALOGEN TYPE]
HEADLAMP AIMING SWITCH
HEADLAMP AIMING SWITCH
Exploded ViewINFOID:0000000003773632
Removal and InstallationINFOID:0000000003773633
REMOVAL
1. Remove the instrument driver lower panel. Refer to IP-11, "Exploded View".
2. Disengage the pawls. And then remove the headlamp aiming switch.
INSTALLATION
Install in the reverse order of removal.
1. Headlamp aiming switch
A. Pawls
JPLIA1106ZZ

EXL-360
< SERVICE DATA AND SPECIFICATIONS (SDS) [HALOGEN TYPE]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Bulb SpecificationsINFOID:0000000003773752
Item Type Wattage (W)
Front combination lampHeadlamp (HI) H9 65
Headlamp (LO) H11 55
Parking Lamp W5W 5
Front turn signal WY21W (Amber) 21
Front fog lamp H11 55
Front side turn signal lamp (integrated into the door mirror) LED —
Rear combination lampStop/tail lamp LED —
Rear turn signal lamp S25 (Amber) 21
Back-up lamp W16W 16
License plate lamp W5W 5
High-mounted stop lamp LED —
Rear fog lamp W21W 21

FRONT BUMPER
EXT-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
MA
B
EXT
N
O
P
ON-VEHICLE REPAIR
FRONT BUMPER
Exploded ViewINFOID:0000000003819529
1. Bumper side bracket RH 2. Bumper stay RH 3. Bumper reinforcement
4. Grommet RH 5. Bumper fascia assembly 6. Bumper molding RH
7. Headlamp washer nozzle cover RH 8. Licence plate bracket 9. Spring nut
10. Headlamp washer nozzle cover LH 11. Bumper molding LH 12. Grommet LH
13. Bumper energy absorber 14. Bumper side bracket LH 15. Bumper stay LH
JMKIA2516ZZ

EXT-12
< ON-VEHICLE REPAIR >
FRONT BUMPER
Removal and Installation
INFOID:0000000003819530
REMOVAL
CAUTION:
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
1. Fully open hood assembly.
2. Remove clips (A) of front bumper fascia upper side.
3. Remove front bumper fascia fixing screws (A) and clips (B) from
front bumper fascia lower side.
4. Disconnect front fog lamp harness connectors (LH/RH).
5. Disconnect headlamp washer tube connector. Refer to WW-97, "
Removal and Installation".
6. Remove fender protector fixing clips to access front bumper fas-
cia fixing screw (A), and then remove front bumper fascia fixing
screws (LH/RH).
16. Front fog lamp bracket RH 17. Front fog lamp bracket LH 18. Front fog lamp LH
19. Bumper upper retainer 20. Front fog lamp RH
JMKIA2517ZZ
JMKIA2518ZZ
JMKIA2519ZZ

FRONT BUMPER
EXT-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
MA
B
EXT
N
O
P
7. Pull bumper fascia side toward the vehicle side to disengage the
bumper fascia from bumper side brackets (LH/RH).
8. Disengage front bumper fascia from bumper brackets (A) (LH/
RH).
9. Remove bumper fascia assembly.
CAUTION:
When removing bumper fascia, 2 workers are required so as to prevent it from dropping.
10. Remove the following parts after removing bumper fascia.
 License plate bracket
 Front bumper retainer
 Front bumper molding (LH/RH)
 Headlamp washer nozzle (LH/RH). Refer to WW-102, "
Removal and Installation".
 Front fog lamps (LH/RH). Refer to EXL-183, "
Removal and Installation".
11. Remove bumper energy absorber.
12. Remove bumper reinforcement mounting nuts, and then remove bumper reinforcement with power tool.
13. Remove bumper stay (LH/RH) mounting bolts, and then remove bumper stay (LH/RH).
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installing, perform fitting adjustment.
: Pawl
JMKIA2520ZZ
JMKIA2521ZZ
JMKIA2550ZZ
Portion Clearance Flush
Front bumper – Front grille A – A 3.5 – 8.5 mm (0.138 – 0.335 in) —
Front bumper – Hood B – B 3.7 – 8.3 mm (0.146 – 0.327 in) —