2008 MERCEDES-BENZ S-Class Comand Manual

152 Control systemsCOMAND telephone*Adding to an existing entry in the
COMAND address book
Slide omp or rotate ymz and select
list entry (
page 150).

Select “Options”
“Save”
“Add”.

Select a number category to add,
e.g. “Home”.

Select a telephone category to add,
e.g. “Land Line”.

Select “Save”.
The search menu for COMAND address
book entries appears.

Search for desired entry.

Press n when you have finished
searching.
COMAND saves the data if there are
fewer than four numbers assigned to
the entry you are searching for in the
selected number category.
If four numbers are saved for the entry
you are searching for, a prompt will ap-
pear asking whether you want to over-
write one of the existing numbers.

Select “Yes” or “No”.
If you select “Yes”, a selection list will
appear containing the four existing
numbers.

Select the number to be overwritten.
COMAND overwrites the selected num-
ber with the new data.
Incoming call
Rejecting or accepting the call
Rejecting: Select “Reject”.
or

Press t on the telephone keypad or
on the multifunction steering wheel.

Accepting: Select “Accept”.
or

Press s on the telephone keypad or
on the multifunction steering wheel.
or

Press 0 on the multifunction steer-
ing wheel.

Use the mobile phone (see mobile
phone operating instructions).
or
i
“Save” does not function if the selected list
entry is already saved in the COMAND address
book.
i
There is a detailed description of searching
for an COMAND address book entry in the
“Searching for an address book entry” section
(
page 170).
i
If you have a CDMA/TDMA mobile phone
and reject a call, only the ring tone will stop. The
call itself can only be ended by the caller.

153 Control systems
COMAND telephone*

Use the Bluetooth
® headset
(see headset operating instructions).
If you have accepted the call using
COMAND, the telephone keypad, the mul-
tifunction steering wheel or the mobile
phone, the call will be conducted via the
hands-free system. The volume of the call
can be adjusted (
page 98).
If you have accepted the call using the
Bluetooth
® headset, the call will be con-
ducted via the headset.
Further operating functions can be found
in the “Functions during a single-call con-
nection” section (
page 155).
You can also accept a call if the
COMAND display is showing a screen oth-
er than the telephone mode screen. After
accepting the call, you will see the caller’s
data in a window.

Closing window: Slide qmr oromp
or press n.
Making an outgoing call
Entering the telephone number using
the COMAND controller
Switching screen to telephone
mode: Call up main telephone menu
(page 149).

Entering digits: Select desired digits
by rotating ymz or sliding omp and
press n.

Deleting individual digits: Select )
and briefly press n.

Deleting an entire telephone num-
ber: Select ) and press and hold n
until the telephone number is deleted.

Connecting a call: Select “S”.
Entering a telephone number using the
telephone keypad

Switching screen to telephone
mode: Call up main telephone menu
(page 149).

Use telephone keypad to enter digits.

Connecting a call: Press s.
i
The use of a Bluetooth
® headset requires
Bluetooth
® to be activated and the Bluetooth
®
headset to be authorized (
page 180).
i
If you place an outgoing call and receive a
busy signal, the telephone automatically starts
to redial as long as the provider and the mobile
phone support this function (see mobile phone
operating instructions).
While the call is connecting, you can also send
character strings (
page 156).
i
A detailed description of how to enter digits
using the telephone keypad can be found on
(
page 90).

154 Control systemsCOMAND telephone*Redial
Switching screen to telephone
mode: Call up main telephone menu
(page 149).

Use COMAND controller to select
“S”.
or

Press s on the telephone keypad
(page 90).
The list of dialed numbers appears. The
most recently dialed number is at the
top.

Select desired entry.

Connecting a call: Press n.Placing a call to a call list entry or
COMAND phone book entry

Call up a call list and select an entry
(page 150).
or

Call up COMAND phone book and se-
lect an entry (
page 158).

Connecting a call: Press n.Speed dialing
You can save telephone numbers in the
speed-dial preset locations on the mobile
phone and call up the speed-dial presets
(see mobile phone operating instructions).
You can also call up speed-dial numbers
using COMAND.
Calling up speed-dial presets using the
COMAND controller

Switching screen to telephone
mode: Call up main telephone menu
(page 149).

Entering number of a speed-dial pre-
set: Select all the digits in sequence.
Deleting individual digits:
Select) and briefly press n.
i
If the list of dialed calls contains no entries,
the “S” menu item cannot be selected and the
s button on the telephone keypad does not
function.
i
By default, the mailbox number is preset in
the speed dial memory unless you have modified
it. For more information on the mailbox
(
page 149).
i
Operation during call connection depends
on the speed-dial preset position called up.

155 Control systems
COMAND telephone*

Deleting entire number:
Select) and press n until the
number is deleted.

Connecting a call (speed-dial pre-
sets 1 -99): Select “S”.
or

Connecting a call (speed-dial pre-
sets 100 - 999): Select “#” after the
digits
“S”.
In both cases, the telephone connects
the call to the saved telephone num-
ber. If the speed-dial memory contains
no telephone numbers, you will see a
corresponding message.

Deleting message: Press n.Calling up speed-dial numbers using the
telephone keypad

Switching screen to telephone
mode: Call up main telephone menu
(page 149).

Single-digit numbers: Press and hold
the A- 9 buttons.
or

Single- and two-digit numbers: Enter
number using the A- 9 buttons.

Press s.
or

Three-digit numbers: Enter number
using the A- 9 buttons.

Press #, and then s.
In all three cases, COMAND connects
the call to the saved telephone num-
ber. If the speed-dial memory contains
no telephone numbers, you will see a
corresponding message.

Deleting message: Press n.Functions during a single-call
connectionIllustration: telephone mode during a call1Symbol for active telephone con-
nection (also visible in other operating
modes)
2Signal strength display
3To switch hands-free microphone on or
off
4Length of call display
5To send character strings
6To end a call
7Person you are calling

156 Control systemsCOMAND telephone*Switching the hands-free microphone
on or off
Switching screen to telephone
mode: Call up main telephone menu
(page 149).

Switching off microphone:
Select “Mic OFF” and press n.
or

Press F shortcut button.
If the microphone is switched off,
the> symbol appears in the main ar-
ea.

Switching on microphone:
Select “Mic ON”.
or

Press F shortcut button.
The> symbol disappears.
Sending a character string via DTMF
Answering machines or other devices can
be controlled by character strings (e.g. for
remote query functions).
Sending character strings via the DTMF
menu

During a call, select “DTMF”.
The DTMF dialing display appears.1Back to the call display
2Character entry
3To call up the phone book

Sending individual characters:
Rotateymz or slide omp and select
desired character.
Each character you select can be seen
in the main area and is sent immediate-
ly.
i
The name of the person you are speaking
with can only be seen in display 7 if his or her
telephone number and name have been saved in
the COMAND address book or phone book on
the mobile phone. The telephone number must
also be saved in the same way in which the per-
son you are talking to transmits it.
i
This function is not possible with every mo-
bile phone. If the mobile phone supports the
function, you can use it during the call connec-
tion and also during a call.

157 Control systems
COMAND telephone*

Sending a phone book entry as a
character string: Select “Name”.

Select desired phone book entry.
The entry is immediately sent as a char-
acter string.

Switching back to the call display:
Select “Y”.
Sending character strings via the tele-
phone keypad

Press corresponding button on tele-
phone keypad.
Each character you select is immedi-
ately sent.Ending an active call

Ending a call: Select “4END” in the
call display.
or

Press t on the telephone keypad or
on the multifunction steering wheel.
The COMAND display will change to
the previously selected display, if
applicable.
Transferring a call
From the hands-free system to the
Bluetooth
® headset
The call transfer is controlled by pressing
the PTT button on the Bluetooth
® headset
(see headset operating instructions). Nor-
mally, it is sufficient to press the PTT but-
ton once, but under certain circumstances
you may have to press it a second time.
Once the call has been transferred to the
Bluetooth
® headset, all the functions will
be available to you which are described in
the “Functions during a single-call connec-
tion” section (
page 155).
Exception: “Switching the hands-free mi-
crophone on or off” function (
page 156).
i
Telephone numbers containing the + char-
acter may impair the function.
i
The + character may impair the function.
i
The use of a Bluetooth
® headset requires
Bluetooth
® to be activated and the Bluetooth
®
headset to be authorized (
page 180).

158 Control systemsCOMAND telephone*From the Bluetooth
® headset to the
hands-free system
On most Bluetooth
® headsets, you press
the PTT button on the headset twice quick-
ly to transfer the call (see headset operat-
ing instructions).
From the hands-free system to the mo-
bile phone

If the mobile phone has a folding up-
per section: Flip upper section open.

Take mobile phone out of cradle.
The “No telephone inserted” message
appears on the COMAND display. Sub-
sequent operation is only possible us-
ing the mobile phone.From the mobile phone to the
hands-free system

Insert mobile phone into cradle.
Once the call has been transferred to
the hands-free feature, all the functions
will be available to you which are de-
scribed in the “Functions during a sin-
gle-call connection” section
(page 155).
COMAND phone book
The COMAND phone book contains both
the COMAND address book entries and
mobile phone entries that have at least
one telephone number.
The COMAND address book entries are
permanently available even when a mobile
phone is not inserted in the cradle.
When the mobile phone is inserted in the
cradle, COMAND will read the phone book
entries in the mobile phone and compares
them with the COMAND address book en-
tries.

159 Control systems
COMAND telephone*
If any of the telephone numbers of a phone
book entry in the mobile phone are the
same as an address book entry, COMAND
will only display the address book entry.
If the entries are not the same, the CO-
MAND phone book will show the phone
book entry in the mobile phone.
Calling up the COMAND phone book
Select “Telephone”
“Name”.
The COMAND phone book appears.
Illustration: a phone book with name dis-
play and smart speller activated1Category symbol
2Upper entry from address book (with-
out category symbol)
3Symbol + for several telephone num-
bers (subentries) under the main entry
4Symbol for summarized entries
from the mobile phone with the same
name but different telephone numbers
5Smart speller
6Voice entry symbol
7To close the phone bookEntries with category symbol 1 come
from the mobile phone. The following cate-
gory symbols are possible:


= symbol for “Mobile” category


= symbol for “Home” category


= symbol for “Work” category


= symbol for “Fax” category


= symbol for “Pager” category


= symbol for “Main” category or for
unknown category or for phone entries
that are saved on the SIM card of a
GSM mobile phone
Entries without a category symbol or with
the symbol come from the COMAND
address book.
Entries with the symbol contain a voice
entry. Voice entries can be added to the
address book (
page 167). This function
is available in vehicles with Voice Control.