2008 MERCEDES-BENZ S-Class Comand Manual

304 Control systemsInstrument cluster control systemThe following settings are available:Switching on or off Blind Spot Assist*

Press ( or & to select the
“Assistance” menu.

Press % or $ to select the “Blind
Spot Assist” function.

Press #.

Press # again if you would like to
change the current status.
Service menu
The “Service” menu is used for

calling up messages


checking tire inflation pressure elec-
tronically with the Advanced TPMS


calling up the maintenance service in-
dicator display


check engine oil level*
Calling up vehicle malfunction, warning
and system status messages stored in
memory
Use the vehicle status message memory
menu to scan malfunction and warning
messages that may be stored in the sys-
tem. Such messages appear in the multi-
function display and are based on
conditions or system status the vehicle’s
system has recorded.
“On when in
Reverse”
The Rear View Camera au-
tomatically switches on
when reverse gear is en-
gaged.
“Disabled”
The Rear View Camera is
not switched on.
i
The menu overview can be found on
(
page 289).


305 Control systems
Instrument cluster control system
The vehicle status message memory menu
only appears if there are any messages
stored.
Press ( or & to select the
“Service” menu.If conditions have occurred causing
status messages to be recorded, the
number of messages appears in the
multifunction display: “2 messages”.

Press % or $ to select the mes-
sage.

Press # to confirm.
Checking tire inflation pressure
For information about checking tire infla-
tion pressure (
page 593).Calling up the maintenance service in-
dicator display
For information about calling up the main-
tenance service indicator display
(
page 612).
Checking engine oil level (S 600 and
S65AMG)
For information about checking engine oil
level (
page 575).
Settings menu
In the “Settings” menu, you can:

switch the daytime running lamps on or
off (USA only)


switch the additional speedometer on
or off


switch the radar sensors* on or off
(USA only)
Warning!
G
Malfunction and warning messages are only
indicated for certain systems and are inten-
tionally not very detailed. The malfunction
and warning messages are simply a remind-
er with respect to the operation of certain
systems and do not replace the owner’s
and/or driver’s responsibility to maintain
the vehicle’s operating safety by having all
required maintenance and safety checks
performed on the vehicle and by bringing
the vehicle to an authorized Mercedes-Benz
Center to address the malfunction and
warning messages (
page 642).
i
See the “Practical hints” section for mal-
function and warning messages (
page 642).
i
If you turn the SmartKey in the starter
switch to position0 and then back to position2,
all messages will be deleted from the message
memory.
i
The menu overview can be found on
(
page 289).

306 Control systemsInstrument cluster control systemSetting daytime running lamp mode
(USA only)
Press ( or & to select the “Set-
tings” menu.

Press % or $ to select the “Day-
time Running Lamps” function.

Press #.

Press # again if you would like to
change the current status.
Depending on the previous status, the
daytime running lamps will be switched
on or off.With “Daytime Running Lamps” mode se-
lected and the exterior lamp switch at po-
sition M or *, the low beam
headlamps are switched on when the en-
gine is running.
In low ambient light conditions the follow-
ing lamps will switch on additionally:


Parking lamps


Tail lamps


License plate lamps


Side marker lamps
For more information on the daytime run-
ning lamp mode (
page 401).Showing or hiding additional
speedometer
You can have an additional digital speed-
ometer shown on the multifunction dis-
play. The speed is shown in the unit of
kilometers/hour (USA) or miles/hour
(Canada).

Press ( or & to select the “Set-
tings” menu.

Press % or $ to select the “Add.
Speedometer” function.

Press #.

Press # again if you would like to
change the current status.
Depending on the previous status, the
additional speedometer will be
switched on or off.
i
This function is not available in countries
where the daytime running lamp mode is manda-
tory and therefore in a constant mode.
i
If you turn the exterior lamp switch to anoth-
er position, the corresponding lamp(s) will
switch on.
i
Make sure that the light switch is set
toB or * when you switch off the day-
time running lamps while driving at night.

307 Control systems
Instrument cluster control system
Switching radar sensors* on/off
If your vehicle is equipped with DISTRONIC
Plus*, BAS Plus*, or Park Assist* it is
equipped with a radar sensor system
which you can switch on and off.
When travelling in Canada in a vehicle not
registered in Canada, you must switch off
the radar sensor system. Canadian law
does not permit the use of the radar sensor
system for vehicles from outside of Cana-
da. When you switch off the radar sensor
system, the following functions are deacti-
vated:

BAS Plus* (
page 70)


PRE-SAFE
® Brake* (
page 77)


DISTRONIC Plus* (
page 451)


Park Assist* (
page 476)


Advanced Parking Guidance*
(page 481)


Blind Spot Assist* (
page 495)

Press ( or & to select the “Set-
tings” menu.

Press % or $ to select the “Ra-
dar Sensors” function.

Press #.

Press # again if you would like to
change the current status.
Depending on the previous status, the
radar sensors will be switched on or
off.
i
USA only:
This device has been approved by the FCC as a
“Vehicular Radar System”. The radar sensor is
intended for use in an automotive radar system
only. Removal, tampering, or altering of the de-
vice will void any warranties, and is not permitted
by the FCC. Do not tamper with, alter, or use in
any non-approved way.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
i
Canada only:
This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference re-
ceived, including interference that may
cause undesired operation of the device.
Removal, tampering, or altering of the device will
void any warranties, and is not permitted. Do not
tamper with, alter, or use in any non-approved
way.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
i
The selected status of the radar sensors re-
mains stored in memory even if the engine is
turned off and restarted.
i
The following message appears in the multi-
function display if the radar sensors are
switched off and you attempt to activate DIS-
TRONIC Plus*, Park Assist* or PRE-SAFE
®
Brake*:
“Radar Sensors
(See Oper. Manual)
Disabled”

308 Control systemsVoice ControlOperating safetyWarning!
G
Please devote your attention first and fore-
most to the traffic situation you are in. While
the system permits hands-free phone oper-
ation, attention to traffic may be diverted
not only by physical operation of a phone,
but also by the distraction of a phone con-
versation while driving. As such, for safety
reasons, we encourage the driver to stop the
vehicle in a safe place before answering or
placing a phone call.
For safety reasons, you should only select a
destination when the vehicle is stationary.
While the navigation system provides direc-
tional assistance, the driver must remain fo-
cused on safe driving behavior, especially
attention to traffic and street signs, and
should utilize the system’s audio cues while
driving.
The navigation system does not supply any
information on stop signs, yield signs, traffic
regulations or traffic safety rules. Their ob-
servance always remains in the driver’s per-
sonal responsibility. DVD maps do not cover
all areas nor all routes within an area.
Traffic regulations always have priority over
any route recommendations given.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet
(approximately 13.5 m) every second.
Warning!
G
Navigation announcements are intended to
direct you while driving without diverting
your attention from the road and driving.
Please always use this feature instead of
consulting the map display for directions.
Consulting the symbols or map display for
directions may cause you to divert your at-
tention from driving and increase your risk
of an accident.Warning!
G
Please do not use the Voice Control System
in an emergency, as the tone of your voice
may change in a stressful situation. This
could cause a delay in completing your
phone call in a timely manner. This could
distract you in an emergency situation and
cause you to be involved in an accident.

309 Control systems
Voice Control introduction
Voice Control introduction
The Voice Control System gives you the ca-
pability to control the following systems on
your vehicle using spoken commands:

Telephone* (
page 313)


Navigation (
page 320)


Address book (
page 330)


Audio (
page 334) (AM/FM radio,
CD/DVD changer, MP3 player)You control these systems using spoken
commands. Moreover, controls such as
the buttons on the multifunction steering
wheel (
page 311) allow you to keep your
hands on the steering wheel.
The command vocabulary consists of
approximately 300 ready to use phrases.
The Voice Control System recognizes com-
mands and number sequences, irrespec-
tive of the speaker. To optimize speech
recognition for your voice follow the indi-
vidualization process (
page 355).
You can use the Voice Control System to
call up all of COMAND’s main menu items,
with the exception of the main menus for
“Vehicle” and “Navi”.The commands and digit sequences can be
spoken without pausing between the indi-
vidual words. If an unavailable or incorrect
command is used, the Voice Control Sys-
tem will prompt you for a new command by
asking “Please repeat” or “Please repeat
your entry”.
In order to provide for a safe and comfort-
able dialog, the Voice Control System ac-
knowledges important commands.

310 Control systemsVoice Control introductionSpelling
You may not need to spell the entire name
(street, intersection, city or point of inter-
est) especially if the name is lengthy. Spell-
ing the first three to five characters of the
name should be sufficient for the system
to recognize the name provided it is avail-
able on the navigation DVD.
The selection appearing on the COMAND
display is sorted based on your recognized
voice input and a matching algorithm.
You can use the commands “Next page” or
“Previous page” to scroll up or down in the
list.
Use the command “Correction” to start
over by again spelling the name.
Speak each character as clearly as you
can, especially when they sound very simi-
lar (d or e).
Command types
The Voice Control System commands can
be categorized as:

General Commands
These are commands always available
to you as soon as the Voice Control
System is activated (for example
“Help” commands).


Local Commands
These are commands specific to the
currently active system shown in the
COMAND display (for example com-
mands to control the CD/DVD chang-
er).
For a complete list of commands
(
page 340).
Active System
The active system is the system currently
shown in the COMAND display.
If, for example, you listen to the radio while
the telephone system is active on the
COMAND display, you have to switch to
the radio using the command “Radio” be-
fore you can operate the radio.
i
During Voice Control System operation visu-
al help windows also appear in the COMAND dis-
play (page 312).

311 Control systems
Voice Control introduction
Controls
Operation via the multifunction
steering wheelActivating Voice Control

Switch on COMAND (
page 87).

Press !.
An audible tone (beep) confirms the ac-
tivation of the system.

Speak a command.
Canceling Voice Control

Press L.
or

Speak the command “Cancel”
(except for speaking voice entries, en-
tering a city or carrying out individual-
ization).
or

Press any COMAND button.
Item
1
!to activate Voice Control
to accept a call
2
Lto cancel Voice Control
3
æto increase volumeçto decrease volumesto take a call
to dial
to redialtto end a call
to reject an incoming call
i
Voice Control can be cancelled at any time,
even during a dialog. Please note that if the Voice
Control System is cancelled during a dialog, then
the complete procedure is stopped and Voice
Control is cancelled.