2008 AUDI A4 AVANT Owners Manual

High beam [D
The ~D warning/indicator light il lu m inates when the high beams are
on or w hen you use the head lig ht flash er. For mo re inf ormation
about using the h igh beams,
see=> page 80 . •
Electronic power control EPC
Th is warn ing /indicator l ig ht m on ito rs the ele ctr onic
po wer co nt rol.
The EPC warning/indicator light (E lectronic Power Control) illumi ­
n at es w he n yo u switch o n the ignitio n as a functi on ch ec k.
[ i] Tips
If thi s wa rning/indi cator light i llum ina tes w hile you a re driving , then
there is a ma lfunction in the engine electronics . Have the malfunc ­
t io n co rre cte d as so on as p oss ible by your auth orized Audi de aler or
qualified wor kshop .•
Brake system BRAKE (USA models)/ (CD)
(Canada models)
Th is warn ing /indicator l ight i llu minates when the brake
fl uid leve l is t oo low or wh en ther e is a ma lf u nct io n in t he
ABS , or when the pa rkin g brake i s se t.
T he lig ht illu min ate s w hen the igni tio n is turn ed on. It goes out aft er
the engine has be en started and the parking bra ke is fu lly released .
T his i ndicate s th at th e br ake w arni ng lig ht is fun cti onin g prop erl y.
If the brake warning light does not light up when the engine is
cranking or the parking brake is applied , there may be a malfunction
in the electrical system. In this case, contact your Audi dealer.
When the l ig ht comes on, an audible warning si gnal is also given.
Controls and equip ­
ment
Instruments and warning /indicator lights
Parking brake set
T he BRAKE or CCD) (Canada) wa rning/indicat or l igh t illum in ate s wh en
t h e pa rkin g b rake is
se t=> ,&.
& WARNING
• USA models : If the BRAKE warning light and the ABS warning
light come on together , the rear wheels could lock up first under
hard braking . Rear wheel lock-up can cause loss of vehicle control
and an accident . Have your vehicle repaired immediately by your
authorized Audi dealer or a qualified workshop. Drive slowly and
avoid sudden, hard brake applications.
• Canada models : If the brake warning light
{(j)) and the ABS
warning light
0 come on together , the rear wheels could lock up
first under hard braking . Rear wheel lock-up can cause loss of
vehicle control and an accident. Have your vehicle repaired imme­
diately by your authorized Audi dealer or a qualified workshop .
Drive slowly and avoid sudden , hard brake applications.
• If the brake warning/indicator light does not go out after a few
seconds and the parking brake released, or lights up while you are
driving, the fluid level in the brake fluid reservoir is too low. If you
believe that it is safe to do so , proceed immediately at low speed
to the nearest authorized Audi dealer or qualified repair facility and have the brake system inspected .
• Always keep in mind that after several brake applications , you
will need greater pressure on the brake pedal to stop your vehicle .
Do not rely on strained brakes to respond with maximum stopping
power in critical situations . You must allow for increased braking
distances . The extra distance u sed up by fading brakes could lead
to an accident . •

Driver inf orma tion di spl ay
Driver information display
Introduction
Applies to vehicles: w ith Driver information display
General notes
The driver information display inside the instrument
cluster provides you, the driver, with important informa­ tion.
Fig. 1 O Ins tru ment
c lu st er: ce nte r dis play
The driver information display is located in the center of the instru­
ment
cluster:::> fig. 10.
The driver information system updates important information in the center display in clear view of the driver . In an easy to understand
format, the display tel ls you how your vehicle is functioning
at th e
c urr ent m om ent .
For example, the display can te ll you how many
miles (ki lometers) you can still drive until it is time to bring your
vehic le to your authorized Audi dealer for a scheduled Maintenance
Service. This feature helps preventing costly repairs. It is just one of
many different items o f information available for recall. The display also gives you a "status report" whenever the
sou
nd sys te m and
n av igatio n
systems are being used.
Detailed instructions for operating the Aud i Naviga tion System* are
provided in separate manuals.
[ i] Tips
If your vehic le has an automatic transmission, the various display
contents will appear only after you have moved the selector lever
into
R , D or S. •
Driver information display with on -board
computer
Radio display
Outside air temperature
Door open indicator
Selector lever position tiptronic®
Speed limiter
Auto Check system Driver information
Parking brake warning
Service interval disp lay
Headlight/taillight malfunction ::::> page25
=:> page25
=:> page26
=:> page 144
=:> page34
::::> page 28
::::> page 29
=:> page29
=:> page 17
=:> page 35

Tire pressure monitoring system
On-board computer
Audi Navigation System*
Sound system display
~ page45
~ page38
See separate man-
ual •
Fig. 1 1 Center d isp lay:
sound system
If, after switching on the radio, the Auto Check system has detected
no priority 2 malfunctions, then the "OK" will disappear and the
radio station call letters and frequency (plus any othe r additional
information) will appear in the display.
These displays appear in addition to the radio display.•
Controls and equip ­
ment
Dri ver inf orma tio n di spl ay
Outside temperature display
F ig. 12 Ce nter disp lay:
o utside te mperature
The outside temperature wil l be displayed when you switch on the
ignition~ fig . 12. If your vehicle has an Automatic transmission, the
outside temperature will appear in the disp lay only after you have
moved the selector lever into a gear (for example, when you shift
into
" D "l.
The snowflake symbo l also appears when the outside temperature
is between 41 °F (+5 °Cl and 23 °F (-5 °Cl. This is to warn you, the
driver, to be extra cautious because the road surfaces may be
ic y. If
the vehicle is at a standstill, or if you are driving at a very low speed,
the tempe rature shown in the display might be s lightly higher than
the actual outside temperature. This is caused by the heat being
radiated from the engine.
Remember, your vehicle is equipped with air conditioning and if
you change the display from °F (Fahrenheit) to °C (Centigrade), then
the outside temperature will automatically be displayed in °C (Centi -
grade)~ page 128. ...
irechnical data

Driver information display
& WARNING
• Never rely exclusively on the outside temperature display to
determine if a road surface is icy or not. Keep in mind that road
surfaces, especially bridges and overpasses, could be ice covered
and slippery even at an outside temperature above 41 °F
1+5 °Cl.
• Always remember, even if the "snowflake" symbol lice
warning) does not appear in the display, black ice could be on the
road .
• Always reduce your speed and drive with special care in cold
weather conditions when the chance of encountering icy road
surfaces increases.
[ i ] Tips
When using the navigation system feature "Destination", the
outside temperature is also displayed.•
Miles (kilometers) to empty
The miles (kilometers) to empty indication is a valuable
aid to schedule the refueling stops on a trip.
Fig . 13 Center display:
miles (kilometers) to
empty
Th is feature shows you the estimated range in miles (kilometers)
:::::, fig. 13 until the tank runs dry. This feature calculates how far you
could drive with the amount of fuel left in your fuel tank while
driving under the current driving conditions. The remaining
distance is recalculated every
6 miles (10 km).
While calculating the miles (kilometers) to empty, the system also
calculates your fuel consumption over the last
18 miles (30 km).
Remember:
-the more economica lly you drive, the further you can
go.•
Warning : engine hood, door or rear lid open
Fig . 14 Display: door ,
rear lid, and engine
hood open
With the ignition switched on, the open-door-or-lid warning illumi­
nates when at least
one door, or the engine hood or the trunk lid is
not closed . The symbol also shows you which door(s) or lid is not
closed. The illustration shows that both the driver's and the right
rear door are not closed
:::::, fig. 14.
If the engine hood or trunk lid are not closed, the display will flash.
As soon as all the doors and lids are properly closed, the warning
goes out.
~

You can switch off the open-door-or-lid warning display by briefly pressing the On Board computer control
but tons => page 39. The
open door or trunk warn ing will, however, illuminate again as soon
as there is a change in the position of the doors, engine hood or
trunk lid. •
On-Board Diagnostic system (OBD)
Malfunction Indicator Lamp (MIL) (USA
models) / (Canada models)
The Malfunction Indicator Lamp (MIU in the instrument cluster
=> page 19, fig. 9 is part of the On -Board Diagnostic (OBD II) system.
The warning/indicator light il luminates when the ignition is
switched on and goes out after the engine starts and the idle has
stabi lized . This indicates that the MIL is working prope rly.
If the light do es not go out after the engine is started, or illuminates
while you are driving, a malfunction may exist in the engine system.
If the light starts flashing, the catalytic converter could be damaged .
Continue driving
w ith redu ced pow er (avoiding sustained high
speeds and/or rapid accelerations) and have the condition
corrected. Contact your authorized Audi dealer.
If the light illuminates, the e lectronic speed limiter may also be
malfunctioning . For more
information=> page 28, "Electronic speed
limiter".
An impr operly c lo se d fuel filler cap may al so cau se th e MIL l amp to
illumi nate
=> page 269. •
Controls and equip ­
ment
Dri ver inf orma tio n di spl ay
On -Board Diagnostics
F ig. 15 Locatio n of
Da ta Li nk Co nnecto r
( DL Cl
On-Board Diagnostics monitors the components of your emission
control system . Each control led component in your engine system
has been assigned a code. In case of a malfunction, the component
wil l be identified and the fault stored as a code in the control
modu le memory.
The M IL lamp may a lso illuminate if there is a leak in the on-board
fuel vapor recovery system. If the light illuminates after a refuelling,
pull off the road and stop the vehicle, then check that the fuel fi ller
cap is proper ly closed
=> page 269.
In order to make an accurate diagnosis, the stored data can only be
displayed using special diagnos tic equipment (generic scan tool for
OBD).
In order to connect the special diagnostic equipment, push the plug
into the Data Link Connector (DLC). The DLC is located to the right of
the engine hood release
lever => fig. 15 .
Your author ized Audi dealer or a qua lified service station can inter­
pre t the code and perform the necessary repair. •
irechnical data

Driver inf orma tion di spl ay
Electronic speed limiter
Your vehicle may be factory equipped with tires that are rated for a
maximum speed of 130 mph (210 km/h}. This is less than the
maximum speed of your vehicle. To reduce the risk of sudden tire
failure and loss of control if the vehicle is operated at excessive speeds, your vehicle also has an electronic speed limiter . The elec ­
tronic speed limiter prevents your vehic le from going faster than the
tire speed rating. For more
information~ page 305, "New tires and
r eplacing tires and wheels" .
If the vehicle approaches the tire speed rating, the engine control
unit wi ll turn off the fuel injectors. You will notice an immediate loss
of engine power and a drop in road speed.
If the engine control unit receives faulty vehicle road speed signals,
t he Malfunc tion Indicator Light (MIU will illuminate. If this occurs,
contact the nearest authorized Audi dea ler for ass istance.
&_ WARNING
Al wa ys o bserve th e pos te d speed l imit s and adjust your sp eed t o
s uit preva ilin g road, traffic and weath er cond ition s. Ne ver drive
yo ur vehicle f aster than the ma xim um spe ed rating of the ti re s
install ed .•
Auto-Check Control
Introduction
Fi g. 16 Au to-Check
C o nt rol: a ll syste ms
c h eck ed OK
Whenever the ignition is turned on, Auto -Check Control checks the
proper functioning of important vehicle components and systems.
Auto -Check Contro l keeps up its continuous monitoring of vehic le
systems even as you are driving.
If Auto Check senses an irregular condition or a malfunction
requiring urgent repair, it generates a specific symbol or short
message in the instrument cluster center display . You will also hear
an audible warning tone . The disp lays a re color coded in either red
or yellow depending on their level of priority.
A red symbol means
D anger , a yellow symbol indicates Warning .
Along with some particular red symbols, a message will appear in
the display to alert the driver to certain conditions. •

Driver information messages
Along with some particular warning/indicator lights and instrument cluster symbols, additional messages will
appear in the display .
A driver information message will appear in the display when, for
example :
a light bulb has burnt
out => page 35,
or if you drive off with the parking brake s till engaged (pulled up).
or before you move the selector lever in gear (automatic transmis­
sion).
Driver information messages can be switched o n by the driver when
a priority 1 symbol appears and flashes =>
page 28.
Sw it c hing on th e dri ver inf orm ati on me ssage
For example, if there is a malfunction in the engine oil pressure, the
~ symbo l will appear in the display . If you press the CHECK button ,
the following message will appear:
Sw itch off en gin e, check oil l evel
The message goes out after approximately 5 seconds. Press the
CHECK button to display the message again.
[ i ] Tip s
The following two messages, Handb ra ke i s a pplie d and Wh en
s tati onary ap ply foot br ake while selecting g ear ,
cannot be
switched on again . T hese messages will remain in the display until
you release the parking brake or unti l you move the selector lever
into a gear .•
Controls and equip ­
ment
Dri ver inf orma tio n di spl ay
Parking brake warning
To release the parking brake, first press the release button in the
lever and lift the lever s lightly. Then lower it all the way down.
If you should drive off with the parking brake still engaged, a
warning tone will sound to remind you to release the pa rking brake.
Also, the following message will appear in the display :
Handbrake is a pplied
The parking brake warning is activated when you drive longer than
3 seconds and faster than 3 mph (5 km/h) .•
Ap plies to vehi cles: w it h ma nua l trans mission
Function test : manual transmission
Fig. 17 Dis pl ay:
man ual trans missio n
fu ncti on test
perfo rmed
The Auto -Check Control will automatically perform a test each time
you switch on the ignition.
If the functions monitored by the Auto-Check Control are working
properly, the
O K => fig. 17 will light up for a few seconds. .,_
irechnical data

Driver information display
If one or more faults exist, the driver information disappears
approximately 15 seconds after the engine has been started and the
appropriate fault symbol appears in the display.
If neither the OK message nor a malfunction message appears in
the display, have the Auto-Check Contro l inspec ted by your autho­
rized Audi dealer. •
Function test: automatic transmission
Fig. 18 Dis play: func ­
tion test automatic
transmission, ignition
ju st turned on
The Auto-Check Contro l will automatically perform a test each time
you switch on the ignition . When the selector lever in
P or N , the
following message appears in the display:
When stationary apply footbrake while selecting gear.
When you a select a different gear (for example : R, D, etc.), the
message will disappear and the Auto-Check function is displayed. If
there are no ma lfunctions, the OK message illuminates for a few
seconds => fig. 18.
If there is a malfunction, then the malfunction message wil l appear
about 15 seconds after the you start the vehicle. At the same time
you will hear a warning tone . If
neither the OK message nor a malfunction message appear in the
display, have the Auto -Check Control inspected by your authorized
Audi dea ler .•
Red symbols
A red symbol means DANGER.
-Pull of the road and stop the vehicle.
Turn off the engine.
Fig. 19 Display: engine
coolant level warning
( p rio rity 1 )
-Check the malfunctioning system. Contact your autho­
rized Audi dealer or a qualified workshop for assistance.
The red symbols mean: