2007 NISSAN TIIDA reverse

TM-676
< ON-VEHICLE REPAIR >[6MT: RS6F94R]
CONTROL LINKAGE
18. Remove the grommet and then remove the shift cable and select cable from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
 Shift the control lever to the neutral position.
 Securely assemble each cable and the selector lever and shifter lever.
 Securely assemble each cable and the cable mounting bracket.
 Securely assemble each cable and the control device assembly.
 Make sure that the claws of grommet are in contact with the floor.
 Be careful about the installation direction and push the control lever knob into the control lever.
CAUTION:
Never reuse control lever knob.
 Tapping work for tapping bolt is not applied to new clutch housing. Do not perform tapping by other than
screwing tapping bolt because tapping is formed by screwing tapping bolt into clutch housing.
CAUTION:
Never reuse tapping bolt.
Install the select cable (the control device assembly side) with the following procedure.
1. While pulling the lock of the select cable in the direction of the
arrow shown, install the select cable to the control device
assembly.
2. Slide the lock (1) of the select cable in the direction of the arrow
as shown to pull up the stopper (2) of the select cable.
3. Install the end of the select cable to the pin of the control device
assembly.
4. Install the lever stopper pin (1) or a pin [3 mm (0.12 in) dia.] to
the control device assembly.
CAUTION:
Select cable cannot be adjusted accurately without a use of
a lever stopper pin or a pin [3 mm (0.12 in) dia.].
NOTE:
A lever stopper pin is not included in control device assembly.
Therefore, if the control device assembly is not replaced, pre-
pare a pin [3 mm (0.12 in) dia.].
5. Check that the control lever does not move in the direction of the
select. If it moves, repeat step 3.
6. Shift the control lever to 4th gear position.
JPDIC0067ZZ
JPDIC0064ZZ
JPDIC0069ZZ

AIR BREATHER HOSE
TM-679
< ON-VEHICLE REPAIR >[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P MR18DE Engine Models
1. Remove the battery. Refer to PG-6, "Removal and Installation".
2. Remove air duct and air cleaner case. Refer to EM-269, "
Removal and Installation".
3. Remove the air breather hose.
CAUTION:
When removing air breather hose, be sure to hold two way connector securely.
K9K Engine Models
1. Remove the air duct.
2. Remove the air breather hose.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Make sure air breather hose is not collapsed or blocked due to folding or bending when installed.
MR18DE Engine Models
 When installing air breather hose on two way connector, aim paint mark face toward the vehicle front.
 When installing air breather hose on two way connector, push it until it hits transaxle case.
 When installing air breather hose to air cleaner case, make sure that clips are fully inserted.
K9K Engine Models
 When installing air breather hose to transaxle, aim paint mark face toward the vehicle front.
 When installing air breather hose to transaxle, push it until it hits transaxle case.
 When installing air breather hose to air duct, make sure that clip is fully inserted.

TRANSAXLE ASSEMBLY
TM-681
< REMOVAL AND INSTALLATION >[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
K9K
Removal and InstallationINFOID:0000000001381644
CAUTION:
If transaxle assembly is removed from the vehicle, always replace CSC (Concentric Slave Cylinder).
Return CSC insert to original position to remove transaxle assembly. Dust on clutch disc sliding parts
may damage seal of CSC and may cause clutch fluid leakage. Refer to CL-11, "
Removal and Installa-
tion".
REMOVAL
1. Drain gear oil. Refer to TM-672, "Draining".
2. Drain clutch fluid and remove clutch tube from CSC. Refer to CL-12, "
Removal and Installation".
CAUTION:
Do not depress clutch pedal during removal procedure.
3. Remove the engine and transaxle as an assembly from the vehicle. Refer to EM-207, "
Removal and
Installation" (MR18DE) or EM-302, "Removal and Installation" (K9K).
4. Remove the transaxle to engine and engine to transaxle bolts.
5. Separate the tranaxle assembly from the engine.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
 The transaxle assembly must not interfere with the wire harnesses and clutch tube.
 When installing transaxle assembly, never bring input shaft into contact with clutch cover.
MR18DE
Tighten bolts to the specified torque.
JPDIC0121GB
1. Transaxle assembly
: Refer to installation.
: Transaxle to engine
: Engine to transaxle
Bolt symbol A B
Quantity 3 6
JPDIC0094ZZ

TM-686
< DISASSEMBLY AND ASSEMBLY >[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
SHIFT FORK AND FORK ROD
1. Reverse output gear 2. Snap ring 3. Reverse baulk ring
4. Return spring 5. Needle bearing 6. Reverse idler shaft
7. Seal washer 8. Washer 9. Reverse input gear
10. Lock washer 11. Spring washer
SFIA3294E

TRANSAXLE ASSEMBLY
TM-687
< DISASSEMBLY AND ASSEMBLY >[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
FINAL DRIVE
1. Reverse fork rod 2. Selector 3. Retaining pin
4. 5th-6th shift fork 5. 3rd-4th shift fork 6. 3rd-4th and 5th-6th fork rod
7. 1st-2nd fork rod
: Replace the parts as a set.
SFIA3295E

TRANSAXLE ASSEMBLY
TM-689
< DISASSEMBLY AND ASSEMBLY >[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
5. Remove the bolts as shown.
6. Remove reverse idler shaft bolt and seal washer.
7. Remove transaxle case (1) upward while rotating selector lever
(2).
8. Remove spring (1) of selector from return bushing (2).
9. Move 1st-2nd fork rod (1), 3rd-4th and 5th-6th fork rod (2), and
reverse fork rod (3) to neutral position.
10. Remove selector (4) from clutch housing.
PCIB1694E
PCIB1695E
JPDIC0105ZZ
PCIB1697E
PCIB1698E

TM-690
< DISASSEMBLY AND ASSEMBLY >[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
11. Remove retaining pin from 5th-6th shift fork using a pin punch.
12. Remove 3rd-4th and 5th-6th fork rod (1) assembly according to
the following.
a. Lift the fork rod up.
b. Remove 3rd-4th and 5th-6th fork rod (1) assembly from clutch
housing.
c. Remove 3rd-4th shift fork and 5th-6th shift fork from 3rd-4th and
5th-6th fork rod.
13. Remove reverse gear assembly (1) according to the following.
a. Lift up the input shaft assembly (2) and mainshaft assembly (3).
b. Remove reverse gear assembly (1) and reverse fork rod (4)
from clutch housing.
14. Remove spring washer located under the reverse idler shaft.
15. Remove input shaft assembly (1), mainshaft assembly (2), and
1st-2nd fork rod (3) from clutch housing.
16. Remove final drive assembly (1) from clutch housing.
17. Remove magnet from clutch housing.
PCIB1699E
PCIB1700E
PCIB1701E
PCIB1702E
PCIB1703E

TRANSAXLE ASSEMBLY
TM-697
< DISASSEMBLY AND ASSEMBLY >[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
15. Install differential side bearing outer race (clutch housing side)
into clutch housing using Tool (A).
CAUTION:
Replace differential side bearing inner race and differential
side bearing outer race as a set.
16. Install differential side oil seals (1) into clutch housing and tran-
saxle case using Tool (A).
17. Install magnet onto clutch housing.
18. Install final drive assembly into clutch housing.
19. Install input shaft assembly (1), mainshaft assembly (2) and 1st-
2nd fork rod (3) into clutch housing.
20. Install spring washer located under the reverse idler shaft.
21. Install reverse gear assembly (1) according to the following.
a. Lift up the input shaft assembly (2) and mainshaft assembly (3).
b. Install reverse gear assembly and reverse fork rod (4) to clutch
housing.
22. Install 3rd-4th shift fork and 5th-6th shift fork to 3rd-4th and 5th-
6th fork rod.Tool number : KV38100200 ( — )
PCIB1722E
Tool number : KV38100300 ( — )
B : Transaxle case side
C : Clutch housing side
Dimension “L1” : 1.2 - 1.8 mm (0.047 - 0.071 in)
Dimension “L
2” : 2.7 - 3.3 mm (0.106 - 0.130 in)
JPDIC0120ZZ
PCIB1702E
PCIB1701E