2007 NISSAN TIIDA reverse

POSITION SWITCH
TM-621
< COMPONENT DIAGNOSIS >[5MT: RS5F91R]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
COMPONENT DIAGNOSIS
POSITION SWITCH
BACK-UP LAMP SWITCH
BACK-UP LAMP SWITCH : Component Parts LocationINFOID:0000000001381673
 Check continuity between terminals 1 and 2.
BACK-UP LAMP SWITCH : Component InspectionINFOID:0000000001381674
1.CHECK BACK-UP LAMP SWITCH
Check continuity between terminals 1 and 2.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace position switch. Refer to TM-635, "
Exploded
View".
PARK/NEUTRAL POSITION (PNP) SWITCH
PARK/NEUTRAL POSITION (PNP) SWITCH : Component Parts LocationINFOID:0000000001381675
PARK/NEUTRAL POSITION (PNP) SWITCH : Component InspectionINFOID:0000000001381676
1.CHECK PARK/NEUTRAL POSITION (PNP) SWITCH
Gear position Continuity
Reverse Yes
Except reverse No
MCIA0157E
Gear position Continuity
Reverse Yes
Except reverse No
MCIA0157E
1 : Position switch
JPDIC0070ZZ

SIDE OIL SEAL
TM-629
< ON-VEHICLE REPAIR >[5MT: RS5F91R]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
ON-VEHICLE REPAIR
SIDE OIL SEAL
Exploded ViewINFOID:0000000001381685
Refer to TM-635, "Exploded View".
Removal and InstallationINFOID:0000000001381686
REMOVAL
1. Remove front drive shafts from transaxle assembly. Refer to XX-XX, "*****".
2. Remove differential side oil seal (1) using suitable tool.
CAUTION:
Do not damage transaxle case and clutch housing.
INSTALLATION
Installation is in the reverse order of removal.
⇐: Front
 Install new differential side oil seal (1) to clutch housing and tran-
saxle case using Tool (A).
CAUTION:
 Do not reuse differential side oil seal.
 When installing, do not incline differential side oil seal.
 Do not damage clutch housing or transaxle case.
 Check oil level after installation. Refer to TM-628, "
Inspection".
PCIB1505E
Tool number : ST27862000 ( — )
Dimension “H
1” : 5.7 - 6.3 mm (0.224 - 0.248 in)
Dimension “H
2” : 16.4 - 17.0 mm (0.646 - 0.669 in)
PCIB1506E

TM-630
< ON-VEHICLE REPAIR >[5MT: RS5F91R]
CONTROL LINKAGE
CONTROL LINKAGE
Exploded ViewINFOID:0000000001381687
Removal and InstallationINFOID:0000000001381688
REMOVAL
1. Remove battery. Refer to PG-6, "Removal and Installation".
2. Remove air duct (Inlet), air duct and air cleaner case. Refer to EM-27, "
Removal and Installation".
3. Press the release button (1) of select cable and shift cable, and
then remove select cable and shift cable from lever of control
shaft (2).
4. Shift control lever to neutral position.
5. Remove control lever knob.
6. Remove center console assembly. Refer to IP-11, "
Removal and
Installation".
7. Remove control device assembly mounting bolts.
8. Remove exhaust front tube, center muffler and heat plate. Refer
to EX-5, "
Removal and Installation".
9. Remove bracket.
10. Remove select cable and shift cable from cable mounting bracket.
11. Remove control device assembly from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
1. Control lever knob 2. Control lever 3. Control device assembly
4. Select cable 5. Shift cable 6. Clutch housing
7. Cable mounting bracket 8. Bracket
A: Black color B: White color
PCIB1508E
SCIA7077E

CONTROL LINKAGE
TM-631
< ON-VEHICLE REPAIR >[5MT: RS5F91R]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
 Securely assemble each cable and lever of control shaft.
 Be careful about the installation direction, and push control lever
knob into control lever.
-⇐: Front
 Make sure that the front/rear claws (1) of control device assembly
are in contact with flange of the floor (2).
InspectionINFOID:0000000001381689
Inspect the following items:
 When control lever is selected to 1st-2nd side and 5th-reverse side, confirm control lever returns to neutral
position smoothly.
 When control lever is shifted to each position, make sure there is no binding or disconnection in each boot.
PCIB1509E
PCIB1510E

TM-632
< ON-VEHICLE REPAIR >[5MT: RS5F91R]
AIR BREATHER HOSE
AIR BREATHER HOSE
Exploded ViewINFOID:0000000001381690
Removal and InstallationINFOID:0000000001381691
REMOVAL
1. Remove battery. Refer to PG-6, "Removal and Installation".
2. Remove air duct (Inlet), air duct and air cleaner case. Refer to EM-27, "
Removal and Installation".
3. Remove air breather hose.
CAUTION:
When air breather hose is removed, be sure to hold 2 way connector securely.
INSTALLATION
Installation is in the reverse order of removal.
 When installing air breather hose on 2 way connector, paint mark must be rearward.
 When installing air breather hose on 2 way connector, push it until it hits the transaxle case.
 When installing air breather hose to air duct and air cleaner case, make sure that clips are fully inserted.
CAUTION:
Make sure air breather hose is not collapsed or blocked due to folding or bending when installed.
1. Air cleaner case 2. Air breather hose 3. Air duct
4. Clip 5. Transaxle assembly 6. 2 way connector
PCIB1511E

TM-634
< REMOVAL AND INSTALLATION >[5MT: RS5F91R]
TRANSAXLE ASSEMBLY
8. Remove engine undercover.
9. Remove front drive shafts. Refer to FAX-10, "
Removal and Installation (Left Side)" and FAX-11, "Removal
and Installation (Right Side)".
NOTE:
Insert a suitable plug into side oil seal after removing front drive shaft.
10. Remove heat insulator and exhaust front tube. Refer to EX-5, "
Removal and Installation".
11. Disconnect position switch harness connector and then disconnect clip from rear housing.
12. Drain gear oil. Refer to TM-628, "
Draining".
13. Disconnect select cable and shift cable from transaxle assembly. Refer to TM-630, "
Removal and Installa-
tion".
14. Support engine assembly and transaxle assembly with a jack.
CAUTION:
When setting a jack, be careful not to bring it into contact with switch.
15. Remove engine mount through bolt-securing nut. Refer to EM-89, "
Exploded View".
16. Remove LH engine mount bracket (transaxle side) bolts.
17. Remove rear engine mount bracket and rear torque rod.
18. Remove transaxle assembly to engine assembly bolts.
19. Remove transaxle assembly from the vehicle.
CAUTION:
Secure transaxle assembly to a jack while removing it.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
When installing transaxle assembly, be careful not to bring transaxle input shaft into contact with
clutch cover.
 If transaxle is removed from the vehicle, always replace CSC. Refer to CL-11, "
Removal and Installation".
 When installing the transaxle assembly to the engine, install the
bolts following the standard below.
(A): M/T to engine
(B): Engine to M/T
 Bleed the air from the clutch hydraulic system. Refer to CL-8, "
Air Bleeding Procedure".
 After installation, check oil level, and check for leaks and loose mechanisms. Refer to TM-628, "
Inspection".
SCIA7084E
Bolt No. 1234
Quantity 2213
Bolt length “ ”
mm (in)55
(2.17)49
(1.93)69
(2.72)55
(2.17)
Tightening torque
N·m (kg-m, ft-lb)48.0
(4.9, 35)
PCIB1517E

TM-636
< DISASSEMBLY AND ASSEMBLY >[5MT: RS5F91R]
TRANSAXLE ASSEMBLY
GEAR COMPONENTS
PCIB1519E
1. Input shaft front bearing 2. Input shaft 3. Snap ring
4. Input shaft rear bearing 5. Adapter plate 6. Bushing
7. 5th input gear 8. 5th baulk ring 9. Spread spring
10. 5th-reverse synchronizer hub 11. 5th-reverse coupling sleeve 12. Lock washer
13. Reverse synchronizer cone 14. Reverse baulk ring 15. Input shaft nut
16. Retaining pin 17. Reverse gear assembly
: Apply gear oil.
: Replace the parts as a set.

TM-638
< DISASSEMBLY AND ASSEMBLY >[5MT: RS5F91R]
TRANSAXLE ASSEMBLY
SHIFT CONTROL COMPONENTS
PCIB1521E
1. Retaining pin 2. 1st-2nd shift fork 3. Bushing
4. 1st-2nd fork rod 5. Lock pin 6. 5th-reverse fork rod
7. Bracket 8. Reverse gear gate 9. 5th-reverse shift fork
10. Check ball 11. 3rd-4th shift fork 12. 3rd-4th fork rod
13. Control shaft 14. O-ring 15. Selector
16. Check ball plug 17. Interlock bolt 18. Bushing
19. Spring 20. Striking interlock
: Apply gear oil.
: Replace the parts as a set.
: Apply Genuine Liquid Gasket, Three Bond TB1215 or the equivalent.