2007 NISSAN TIIDA reverse

TM-698
< DISASSEMBLY AND ASSEMBLY >[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
23. While lifting up fork rod (1), install 3rd-4th and 5th-6th fork rod
assembly to clutch housing.
CAUTION:
Replace the 5th-6th shift fork, the 3rd-4th shift fork, and the
3rd-4th and 5th-6th fork rod as a set.
24. Install retaining pin into 5th-6th shift fork using suitable tool.
CAUTION:
Do not reuse retaining pin.
25. Move 1st-2nd fork rod (1), 3rd-4th and 5th-6th fork rod assembly
(2), and reverse fork rod (3) to neutral position.
26. Install selector (4) into clutch housing.
27. Install spring of selector into return bushing.
28. Apply recommended sealant onto the mating surface of tran-
saxle case.
CAUTION:
 Remove old sealant adhering to the mating surfaces. Also
remove any moisture, oil, or foreign material adhering to
both mating surfaces.
 Check for damage on the mating surface.
 Use Genuine Liquid Gasket, Three Bond 1215 or an equiv-
alent
 Apply a continuous bead of liquid gasket to the mating surface.
29. Engage shift finger and selector by moving selector lever (1).
Install transaxle case to clutch housing.
PCIB1700E
PCIB1699E
SCIA7782E
JPDIC0110ZZ

TRANSAXLE ASSEMBLY
TM-699
< DISASSEMBLY AND ASSEMBLY >[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
30. Install seal washer and reverse idler shaft bolt, and then tighten
bolt to the specified torque.
CAUTION:
Do not reuse seal washer.
31. Tighten the bolts to the specified torque.
32. Apply recommended sealant to threads of position switch (1).
Then install it to transaxle case and tighten to the specified
torque.
Use Genuine Liquid Gasket, Three Bond 1215 or an equiv-
alent.
33. Install bracket (2), and then tighten the bolt to the specified
torque.
34. Install shifter lever (3), and then install retaining pin using suit-
able tool.
CAUTION:
Do not reuse retaining pin.
35. Install new gasket onto drain plug and tighten to the specified
torque.
CAUTION:
Do not reuse gasket.
36. After gear oil is filled, Install new gasket onto filler plug and tighten to the specified torque.
CAUTION:
Do not reuse gasket.
PCIB1695E
PCIB1694E
SCIA7784E

INPUT SHAFT AND GEAR
TM-701
< DISASSEMBLY AND ASSEMBLY >[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
5. Remove snap ring (1), washer and 5th input gear (2).
6. Remove washer.
7. Remove snap ring (1), washer, 4th input gear (2) and 3rd-4th
synchronizer assembly (3).
8. Remove snap ring (1), washer and 3rd input gear (2).
9. Remove input shaft front bearing (1) from input shaft using a
press.
AssemblyINFOID:0000000001381650
Note the following, and assembly is in the reverse order of disassembly.
PCIB1754E
PCIB1753E
PCIB1752E
PCIB1751E

REVERSE IDLER SHAFT AND GEAR
TM-709
< DISASSEMBLY AND ASSEMBLY >[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
REVERSE IDLER SHAFT AND GEAR
Exploded ViewINFOID:0000000001381656
Refer to TM-635, "Exploded View".
DisassemblyINFOID:0000000001381657
1. Remove reverse output gear (1).
2. Remove snap ring (1).
3. Remove reverse baulk ring (1) and return spring (2).
4. Remove snap ring (1), lock washer (2), reverse input gear (3)
and washer.
PCIB1760E
PCIB1759E
PCIB1758E
PCIB1757E

TM-710
< DISASSEMBLY AND ASSEMBLY >[6MT: RS6F94R]
REVERSE IDLER SHAFT AND GEAR
5. Remove needle bearings (1) and washer from reverse idler
shaft.
AssemblyINFOID:0000000001381658
Note the following, and assemble in the reverse order of disassembly.
CAUTION:
 Never reuse snap ring.
 Make sure that snap ring is securely installed in the groove.
PCIB1761E

SERVICE DATA AND SPECIFICATIONS (SDS)
TM-715
< SERVICE DATA AND SPECIFICATIONS (SDS) [6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General SpecificationINFOID:0000000001381667
TRANSAXLE
Engine type MR18DE K9K
Transaxle modelRS6F94R
Number of speeds6
Synchromesh typeWarner
Shift pattern
Gear ratio 1st3.7273
2nd 2.1053 1.9474
3rd 1.4516 1.3226
4th 1.1714 0.975
5th 0.9714 0.7632
6th 0.8108 0.6383
Reverse 3.6865
Final gear 3.9333 3.7333
Number of teeth Input gear 1st 11
2nd 19
3rd 31
4th 35 40
5th 35 38
6th 37 47
Reverse 11
Main gear 1st 41
2nd 40 37
3rd 45 41
4th 41 39
5th 34 29
6th 30
Reverse 42
Reverse idler gear Input/Output 28/29
Final gear Final Gear/Pinion 59/15 56/15
Side Gear/Pinion
mate gear13/10
Oil capacity
(US pt, Imp pt)Approx. 2.0 (4-1/4, 3-1/2)
Remarks Reverse synchronizer Installed
Triple-cone synchronizer 1st and 2nd
PCIB1769E

CONTROLLER
VTL-7
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
ON-VEHICLE REPAIR
CONTROLLER
Removal and InstallationINFOID:0000000001696279
REMOVAL
1. Remove cluster lid C and instrument finisher D. Refer to IP-11, "Removal and Installation".
2. Remove the front air control screws and release the front air
control clips, and then remove the front air control.
INSTALLATION
Installation is in the reverse order of removal.
Disassembly and AssemblyINFOID:0000000001696280
DISASSEMBLY
SJIA0687E
1. Front air control 2. FRE button 3. MODE ring
4. TEMP ring 5. A/C finisher 6. A/C button
7. TEMP button 8. REC button 9. LCD ring
10. Rear DEF button 11. AUTO button 12. FAN button
13. MODE button
ZJIA0641J

VTL-8
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
CONTROLLER
1. Remove rear DEF button (1) using a suitable tool (A) as shown.
2. Remove A/C button (1) using a suitable tool (A) as shown.
3. Remove FRE button (1) and REC button (2) using a suitable tool
as shown.
ASSEMBLY
Assembly is in the reverse order of disassembly.
ZJIA0792J
ZJIA0793J
ZJIA0794J