2007 NISSAN TIIDA reverse

IN-VEHICLE SENSOR
VTL-9
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
IN-VEHICLE SENSOR
Removal and InstallationINFOID:0000000001696282
REMOVAL
1. Remove instrument lower finisher. Refer to IP-11, "Removal and Installation".
2. Remove in-vehicle sensor screw (A), and then remove in-vehi-
cle sensor (1) from instrument lower finisher (2).
INSTALLATION
Installation is in the reverse order of removal.
SJIA0688E

VTL-10
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
SUNLOAD SENSOR
SUNLOAD SENSOR
Removal and InstallationINFOID:0000000001696283
REMOVAL
1. Remove instrument upper mask using a suitable tool as shown.
2. Disconnect sunload sensor connector, and then remove sunload
sensor (1).
INSTALLATION
Installation is in the reverse order of removal.
SJIA0689E

INTAKE SENSOR
VTL-11
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
INTAKE SENSOR
Removal and InstallationINFOID:0000000001696284
REMOVAL
1. Remove the evaporator. Refer to VTL-16, "Removal and Installation".
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
2. Remove the intake sensor (1) from the evaporator (2).
CAUTION:
Mark the position of intake sensor on the evaporator for
installation.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
 Replace O-rings for A/C piping with new ones, and then apply compressor oil to it when installing it.
 Install the intake sensor in the same position as the original intake sensor.
 When recharging refrigerant, check for leaks.
ZJIA0798J

A/C UNIT ASSEMBLY
VTL-13
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
7. Remove console box assembly. Refer to IP-11, "Removal and Installation"
8. Remove the instrument stay nuts (A) and harness clamps (B),
and then remove instrument stay (1).
9. Disconnect intake sensor connector (1).
10. Remove instrument panel and pad. Refer to IP-11, "
Removal and Installation".
11. Remove side ventilator ducts. Refer to VTL-23, "
Removal and Installation".
12. Remove center ventilator ducts. Refer to VTL-23, "
Removal and Installation".
13. Remove the side kicking plates. Refer to INT-20, "
Removal and Installation".
14. Disconnect the fuel filler door cable and the rear hatch door cable (if equipped).
15. Remove A/C unit assembly bolts, steering member bolts, steering column nuts and harness clips.
16. Remove steering member, and then remove A/C unit assembly.
INSTALLATION
Installation is in the reverse order of removal.
 Fill the cooling system with coolant. Refer to CO-11, "
Changing Engine Coolant" (HR16DE), CO-35, "Chang-
ing Engine Coolant" (MR18DE), CO-58, "Refilling" (K9K).
 Recharge the refrigerant. Refer to HA-29, "
HFC-134a (R-134a) Service Procedure".
CAUTION:
 Replace O-rings for A/C piping with new ones, and then apply compressor oil to it when installing it.
 When recharging refrigerant, check for leaks.
SJIA0646E
SJIA0690E
A/C unit assembly bolt : 6.9 N·m (0.7 kg-m, 61 in-lb)
Steering member bolt : 12 N·m (1.25 kg-m, 9 ft-lb)
Steering column nut : -Refer to ST-9, "
Removal and Installation".

VTL-16
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
EVAPORATOR
EVAPORATOR
Removal and InstallationINFOID:0000000001696371
REMOVAL
1. Remove the A/C unit assembly. Refer to VTL-12, "Removal and Installation".
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
2. Remove the air conditioner filter.
3. Remove foot duct (right). Refer to VTL-23, "
Removal and Installation".
4. Remove screws (A), and then remove expansion valve cover
(1).
NOTE:
Manual A/C system shown, automatic A/C system similar.
5. Remove screws (A), and then remove evaporator cover (1).
NOTE:
Manual A/C system shown, automatic A/C system similar.
6. Remove the evaporator (1) with lower blower case (2) from the
A/C unit assembly.
7. Remove the intake sensor (3) from the evaporator (1).
CAUTION:
Note the position of the intake sensor on the evaporator for
installation.
8. Remove the evaporator (1) from the lower blower case (2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
 Replace O-rings for A/C piping with new ones, and then apply compressor oil to it when installing it.
 Install the intake sensor in the same position on the evaporator.
 When recharging refrigerant, check for leaks.
SJIA0673E
SJIA0674E
SJIA0599J

HEATER CORE
VTL-17
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
HEATER CORE
Removal and InstallationINFOID:0000000001696357
REMOVAL
1. Remove the A/C unit assembly. Refer to VTL-12, "Removal and Installation".
2. Remove foot duct (left). Refer to VTL-23, "
Removal and Installation".
3. Remove the heater pipe cover screws (A), and then remove the
heater pipe cover (1).
4. Remove the heater pipe clip screw (B), and then remove the
heater pipe clip (2).
5. Slide the heater core (3) out of the A/C unit assembly to remove.
INSTALLATION
Installation is in the reverse order of removal.
SJIA0693E

VTL-18
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
BLOWER MOTOR
BLOWER MOTOR
Removal and InstallationINFOID:0000000001696287
REMOVAL
1. Remove instrument panel and pad. Refer to IP-11, "Removal and Installation".
2. Remove side ventilator duct (right). Refer to VTL-23, "
Removal and Installation".
3. Disconnect front blower motor connector (1).
4. Push the flange holding hook (A) toward the front blower motor
(2), then rotate the front blower motor (2) clockwise and remove
it from the A/C unit assembly.
CAUTION:
When front blower fan and front blower motor are manufac-
tured, the balance is adjusted, do not disassemble to
replace the individual parts.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Rotate the front blower motor until the front blower motor flange holding hook locks securely into the
A/C unit assembly.
LJIA0199E

FAN CONTROL AMPLIFIER
VTL-19
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
FAN CONTROL AMPLIFIER
Removal and InstallationINFOID:0000000001696291
REMOVAL
1. Remove the A/C unit assembly. Refer to VTL-12, "Removal and Installation".
2. Remove the fan control amp. screws (A), and then remove the
fan control amp. (1).
INSTALLATION
Installation is in the reverse order of removal.
SJIA0696E