2007 MITSUBISHI LANCER EVOLUTION service

INTERIOR -Instrument Panel52A-9
REMOVAL SERVICE POINT
AA"SRS FRONT PASSENGER’S AIR BAG MODULE
REMOVAL
Insert the flat tipped screw driver into the position shown
in the illustration and pull up the screw driver to disengage
the claws for removal of the front passenger’s air bag module.
Caution
1. Do not damage the claws of the hinge when removing
the front passenger’s air bag module.
2. Store the removed front passenger’s air bag module
facing the deployed side upward in a clean and dry
place.
DISASSEMBLY AND REASSEMBLY
1314
15 c12
13
2
32
4
6
75
7
10
18
916
15
11 cc
c
c
cccc
cc
c
cc
e
c
c e
c
c
c c
c
c
Disassembly steps
1. Instrument panel upper support
2. Side defroster duct
3. Center defroster duct
4. Distribution duct
5. Driver side upper bracket
6. Center upper reinforcement
7. Instrument panel center reinforcement
8. Bridge reinforcement9. Center lower reinforcement
10. Glove box striker
11. Glove box cover
12. Instrument panel pad
13. Side demister
14. Defroster garnish
15. Side air outlet assembly
16. Instrument panel

INTERIOR -Rear Floor Console52A-14
DISASSEMBLY SERVICE POINT
AA"REMOVAL OF CONSOLE LID ASSEMBLY
Insert the special tool into the hinges of the console lid
assembly and the rear floor console through the ashtray
mounting hole to pry for removal.Console lid assembly
Ashtray
mounting
hole Rear floor
console
MB990784
Hinges
View A
View A

INTERIOR -Trims/Headlining52A-17
REMOVAL SERVICE POINT
AA"FRONT PILLAR TRIM REMOVAL
Release the clip to pull towards the direction shown in the
illustration and remove the front pillar trim.
HEADLINING
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
Removal and Installation of Front Pillar Trim, Center
Pillar Trim, upper, Rear Pillar Trim (Refer to P.52A-15.)
12
3 4 56
45
Removal steps
1. Assist grip
2. Room lamp assembly
3. Front room lamp
AA"4. Sunvisor holder5. Sunvisor assembly
DFront floor console assembly
(Refer to P.52A-10.)
AB"6. Headlining
Section A – A
Front pillar trim
A
AFront pillar trim
Instrument
panel

INTERIOR -Headlining52A-18
REMOVAL SERVICE POINTS
AA"SUNVISOR HOLDER REMOVAL
Insert the special tool into sides claws of the sunvisor holder
through the both sides of the sunvisor holder to remove the
hinges.
AB"HEADLINING REMOVAL
Bend the headlining to remove from the front passenger’s
door.
Sunvisor holder
MB990784
MB990784

INTERIOR -Seat52A-19
SEAT
FRONT SEAT
REMOVAL AND INSTALLATION
1
1
2
2 3
3
44±10 NSm
44±10 NSm
30±5NSm
30±5NSm
1. HeadrestFront seat assembly removal steps
2. Front seat anchor cover
"AA3. Front seat assembly
INSTALLATION SERVICE POINT
"AAINSTALLATION OF FRONT SEAT ASSEMBLY
(1) Temporarily tighten the nuts and bolts in all mounting
locations shown in the illustration with no load applied
to the front seat cushion and check the operation of the
seat slide.
(2) Tighten the nuts and bolts in all mounting locations to
the specified torque.

INTERIOR -Seat52A-22
REMOVAL SERVICE POINT
AA"REMOVAL OF HEADREST GUIDE
REAR SEAT
REMOVAL AND INSTALLATION
12
3
22±4NSm
3
Disassembly steps
"BA1. Rear seat cushion assembly
"AA2. Rear seatback assembly3. Rear seat hook

INTERIOR -Seat52A-23
INSTALLATION SERVICE POINTS
"AAINSTALLATION OF REAR SEATBACK
ASSEMBLY/REAR SEATBACK SIDE ASSEMBLY
L.H., R.H.
Press the rear seatback assembly in the direction shown
in the illustration and fit the attachment wire into the hook
securely to install the rear seatback assembly.
"
BAINSTALLATION OF REAR SEAT CUSHION
ASSEMBLY
Fit the rear seat cushion into the rear seat hook securely.
Rear seat back
assembly
Attachment wire
Hook
Rear seat cushion
assembly
Rear seat
hook

52B-1
SUPPLEMENTAL
RESTRAINT
SYSTEM (SRS)
CONTENTS
GENERAL INFORMATION 2..................
SRS SERVICE PRECAUTIONS 3..............
SPECIAL TOOLS 5...........................
TEST EQUIPMENT 6.........................
TROUBLESHOOTING 6.......................
SRS MEINTENANCE 42......................
POST-COLLISION DIAGNOSIS 45.............
INDIVIDUAL COMPONENT SERVICE 49.......
WARNING/CAUTION LABELS 49..............SRS AIR BAG CONTROL UNIT
(SRS-ECU) 50................................
AIR BAG MODULES AND CLOCK
SPRING 52..................................
SEAT BELT PRE-TENSIONER 61..............
AIR BAG MODULE AND SEAT BELT
PRE-TENSIONER DISPOSAL
PROCEDURES 64............................
Undeployed Air Bag Module and Seat Belt
Pre-tensioner Disposal 64.......................
Deployed Air Bag Module and Seat Belt
Pre-tensioner Disposal Procedures 75............
CAUTION
DCarefully read and observe the information in the SERVICE PRECAUTIONS (P.52B-3.) prior to any service.
DFor information concerning troubleshooting or maintenance, always observe the procedures in the Troubleshooting
(P.52B-6.) section.
DIf any SRS components are removed or replaced in connection with any service procedures, be sure to follow the
procedures in the INDIVIDUAL COMPONENT SERVICE section (P.52B-49.) for the components involved.
DIf you have any questions about the SRS, please contact your local distributor.