2007 MITSUBISHI LANCER EVOLUTION instrument panel

INDEX - In order of parts nameC-17
Wiring diagram
page Circuit diagram page Connector
No. Parts name
IInstrument panel wiring harness and
J/B combinationC-211B-54,55,78,92,100,105,108,113,117,
119,123,125,128,137,141,150,154,
158,164,170,172,174,180,185,188,
189,204,205,219,227,237,247,248,
250,252,254B-22,28
Instrument panel wiring harness and
J/B combinationC-213B-54,55,78,82,83,84,87,92,95,100,
104,105,107,108,110,112,113,115,
116,117,119,120,121,123,125,126,
128,129,135,136,137,139,140,141,
149,150,153,154,157,158,164,170,
171,172,173,174,180,185,187,188,
189,191,192,193,195,198,200,204,
205,206,208,212,213,214,219,220,
221,222,227,228,229,230,237,238,
239,240,247, 248,250,252,254,256B-22,28
Intercooler water spray motorA-44B-256B-7,9
Intercooler water spray relayC-222B-54,55,256B-23,29
Intercooler water spray switchD-34B-257B-31,33
JJ/C (1)C-05B-56,62,93,101,104,107,111,112,115,
116,118,122,124,125,127,128,131,
133,136,137,140,141,148,152,153,
156,158,164,170,172,175,181,185,
187,191,194,195,196,197,212,214,
220,222,228,230,238,240,257B-18,24
J/C (2)C-102B-57,63,87,92,104,105,107,111,113,
115,119,124,126,127,131,136,140,
143,154,158,163,169,170,175,181,
187,188,191,192,202,204,210,218,
219,226,236,237,246,248,252,256,
258B-20,26
J/C (3)C-08B-58,64,95,104,105,107,108,112,113,
116,117,119,123,124,125,126,127,
128,129,131,133,136,137,140,141,
149,153,159,164,165,171,172,173,
175,180,181,185,187,188,189,191,
193,194,195,202,210,214,218,222,
226,227,230,236,240,246,247,253,
255,257,258B-18,24
J/C (4)C-26B-59,65,92,100,105,113,119,137,157,
158,170,188,194,197,201,204,205,
209,213,219,221,227,232,237,242,
247,250,252,254,258B-19,25
J/C (5) C-29B-60,84,87,104,112,125,137,149,150,
157,187,194,197,198,214,230,248,
256B-19
J/C (5) C-28B-66,100,108,117,123,141,164,172,
173,189,205,227,247,254B-25
J/C (6)C-108B-61,67,82,83,86,88,90,92,94,96,98,
100,102,149,153,176,182,198,204,
205,206,212,215,219,223,228,231,
237,241,252,253,254,255B-20,26

GENERAL -Supplemental Restraint System (SRS)00-21
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
To improve safety, the SRS and seat belts with
pre-tensioner. These systems enhance collision
safety by restraining the front passengers in case
of an accident. The SRS works with the
pre-tensioner simultaneously when a collision is
detected.
The SRS consists of two air bag modules, SRS
air bag control unit (SRS-ECU), SRS warning lamp
and clock spring. The air bags are located in the
center of the steering wheel, above the glove box.
Each air bag has a folded air bag and an inflator
unit. The SRS-ECU under the floor console monitors
the system and has a safing G-sensor and an
analog G-sensor. The warning lamp on theinstrument panel indicates the operational status
of the SRS. The clock spring is installed in the
steering column. The seat belt pre-tensioner is built
into the front seat belt retractor. Only authorized
service personnel should do work on or around
the SRS components and seat belt with
pre-tensioner. Those service personnel should read
this manual carefully before starting any such work.
Extreme care must be used when servicing the
SRS to avoid injury to the service personnel (by
inadvertent deployment of the air bags or
inadvertent operation of the seat belt with
pre-tensioner) or the driver (by rendering the SRS
or the seat belt with pre-tensioner inoperative).
Diagnosis
connectorFront passenger’s
air bag module
Clock spring Driver’s air bag
module
SRS-ECU
SRS warning lamp
Driver’s air bag
Front
passenger’s
air bag
Seat belt with
pre-tensioner

GENERAL -Supplemental Restraint System (SRS)00-23
SRS-ECU
Terminal No.Destination of harnessCorrective action
7Instrument panel wiring harness→EarthRepair or replace each wiring
harness
8Instrument panel wiring harness→Combination meter
(SRS warning lamp)
harness
9, 10Instrument panel wiring harness→Front passenger’s air bag
module
11 , 1 2Instrument panel wiring harness→Clock spring→Driver’s air bag
module)Repair or replace the dash wiring
harness. Replace clock spring.
13Instrument panel wiring harness→Junction block (fuse No.3)Repair or replace each wiring
harness
16Instrument panel wiring harness→Junction block (fuse No.2)
harness.
20Instrument panel wiring harness→Diagnosis connector
29, 30Floor wiring harnessàDriver’s seat belt pre-tensioner
27, 28Floor wiring harnessàFront passenger’s seat belt pre-tensioner
6. Inspection of the SRS-ECU harness connector should be carried out by the following procedure.
Insert the special tool (probe, MB991222, in the harness set) into the connector from harness side
(rear side), and connect the tester to this probe. If any tool than specified is used, damage to the
harness and other components will result. Furthermore, measurement should not be carried out by
touching the probe directly against the terminals from the front of the connector. The terminals are
plated to increase their conductivity, so that if they are touched directly by the probe, the plating
may break, which will cause drops in reliability.
MB991222 SRS-ECU harness connector
SRS-ECU harness connector (rear view)
7. SRS components and seat belt with pre-tensioner should not be subjected to hart, so remove the
SRS-ECU, driver’s and front passenger’s air bag modules, clock spring, and seat belt with pre-tensioner
before drying or baking the vehicle after painting.
DSRS - ECU, air bag module, clock spring : 93Æ
or more
DSeat belt with pre-tensioner : 90Æ
or more
8. Whenever you finish servicing the SRS, check warning lamp operation to make sure that the system
functions properly. (Refer to P.52B-6.)
9. Make certain that the ignition switch is LOCK (OFF) position when the MUT-IIis connected or
disconnected.
10. If you have any questions about the SRS, please contact your local distributor.
NOTE
SERIOUS INJURY CAN RESULT FROM UNINTENDED AIR BAG DEPLOYMENT, SO USE ONLY
THE PROCEDURES AND EQUIPMENT SPECIFIED IN THIS MANUAL.

MPI -Engine-ECU13A-147
ENGINE-ECU
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operations
Glove Box Assembly Removal and Installation (Refer
to GROUP 52A - Instrument Panel.)
15.0±1.0N·m
2
Removal steps
1. Engine-ECU connector
2. Engine-ECU

MANUAL TRANSMISSION -Sensor, Switch and Relay or vehicles with ACD and AYC>22A-56
SENSOR, SWITCH AND RELAY VEHICLES WITH ACD AND AYC>
REMOVAL AND INSTALLATION
Caution
Before removing the steering wheel and air bag module assembly, be sure to refer to GROUP
52B Precautions in Servicing and Airbag Module Clock Spring.
1
3
2
4
5
Parking brake lever
Steering wheel sensor removal
steps
DSteering wheel and column cover
(Refer to GROUP 37A.)
1. Steering wheel sensor
G sensor removal steps
DFloor console (Refer to GROUP 52A.)
2. Longitudinal G sensor
3. Lateral G sensorElectric pump relay removal
4. Electric pump relay
ACD mode switch removal steps
DInstrument panel ornament (Refer to
GROUP 52A – Instrument Panel.)
5. ACD mode switch
NOTE
For details on the wheel speed sensor, refer to GROUP
35B.
REMOVAL SERVICE POINT
AA"STEERING WHEEL SENSOR REMOVAL
Remove the steering wheel sensor from the column switch.
Caution
Make sure no oil adheres to the steering wheel sensor
because a photocoupler is used.Steering wheel sensor

EXTERIOR -Outside Mirror51-23
OUTSIDE MIRROR
SPECIAL TOOL
ToolNumberNameApplication
MB990784Ornament removerRemoval of power remote control outside
mirror switch
OUTSIDE MIRROR
REMOVAL AND INSTALLATION
123 4
6 7
1
Claw
A
A
Section A - A5
AA
2
7.4±1.4 N·m
Outside mirror removal steps
1. Cover
2. Delta inner cover
3. Outside mirror assembly
4. Outside mirror
A
A"5. MirrorRemote control outside mirror switch
removal steps
6. Instrument panel ornament (Refer to
GROUP 52A - Instrument Panel.)
7. Remote control mirror switch

52A-2
INTERIOR
CONTENTS
SPECIAL TOOL 3............................
INSTRUMENT PANEL* 3......................
FRONT FLOOR CONSOLE 10................
REAR FLOOR CONSOLE 12..................
TRIMS 15....................................
HEADLINING 17..............................SEAT 19.....................................
Front Seat 19..................................
Rear Seat 22..................................
SEAT BELT 25...............................
Front Seat Belt 25.............................
Rear Seat Belt 26..............................
WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
WARNING!
(1) Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to personal
injury or death to service personnel (from inadvertent firing of the air bag) or to the driver and passenger (from rendering
the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an authorized
MITSUBISHI dealer.
(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B - Supplemental
Restraint System (SRS) before beginning any service or maintenance of any component of the SRS or any SRS-related
component.
NOTE
The SRS includes the following components: SRS-ECU, SRS warning lamp, air bag module, clock spring and interconnecting
wiring. Other SRS-related components (that may have to be removed/installed in connection with SRS service or maintenance) are
indicated in the table of contents by an asterisk (*).

INTERIOR -Special Tool/Instrument Panel52A-3
SPECIAL TOOL
ToolNumberNameApplication
MB990784Ornament removerRemoval of switches and trims
INSTRUMENT PANEL
REMOVAL AND INSTALLATION
The following bolts and screws are used for installing the instrument panel.
Bolts and screws are indicated as marks shown in the illustration in the sections of “Removal and Installation”
and “Disassembly and Reassembly.”
NameMarkDimensions mm
(screw diameter x
screw length)ColorShape
Tapping screwa5×16Black
b5×16-
c5×12-
Bolt with washerd6×16-
e6×12-