2007 MITSUBISHI LANCER EVOLUTION rear

INTERIOR -Rear Floor Console52A-13
DISASSEMBLY AND REASSEMBLY
1
23
4 56
7
8
9 102


Disassembly steps
1. Ashtray
2. Cup holder
3. Hole lock
4. Rear floor console
AA"5. Console lid assembly6. Console lid
7. Lower lid striker
8. Hinge bracket
9. Box
10. Rear floor console

INTERIOR -Rear Floor Console52A-14
DISASSEMBLY SERVICE POINT
AA"REMOVAL OF CONSOLE LID ASSEMBLY
Insert the special tool into the hinges of the console lid
assembly and the rear floor console through the ashtray
mounting hole to pry for removal.Console lid assembly
Ashtray
mounting
hole Rear floor
console
MB990784
Hinges
View A
View A

INTERIOR -Trims52A-15
TRIMS
REMOVAL AND INSTALLATION
NOTE
Refer to GROUP42 for more information regarding door trim.
8
44±10 N•m
11
1 2649510
1312
3
7
15
16
14
Removal steps
1. Front scuff plate
2. Cowl side trim
3. Rear scuff plate
4. Front door opening trim
5. Rear door opening trim
AA"6. Front pillar trim
7. Center pillar trim, lower
8. Front seat belt connection9. Center pillar trim, upper
10. Rear pillar trim
11. Rear shelf trim
12. Speaker garnish
13. Retractor trim
14. Partition board
15. Rear end trim
16. Trunk side trim

INTERIOR -Trims52A-16
CLIP POSITION
NOTE
: Clip position
: Claw position
Section B - B
Section C - C
Section D - DSection E - ESection A - A
A ABB
C CC
CD
ClipFront pillar trim
Rear pillar trimFront scuff plate,
Rear scuff plate
Speaker garnish
Section F - F
Rear shelf
trim E
E
Front pillar trim,
Center pillar trim,
upper,
Rear pillar trim
Headlining
BBB
D
F
F
B
GG
Section G - G
Rear end trimClip
Clip
ClipClip
ClipClip H
HI
I
Section H - HSection I - I
Retractor trimRetractor trim
Craw
Craw

INTERIOR -Trims/Headlining52A-17
REMOVAL SERVICE POINT
AA"FRONT PILLAR TRIM REMOVAL
Release the clip to pull towards the direction shown in the
illustration and remove the front pillar trim.
HEADLINING
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
Removal and Installation of Front Pillar Trim, Center
Pillar Trim, upper, Rear Pillar Trim (Refer to P.52A-15.)
12
3 4 56
45
Removal steps
1. Assist grip
2. Room lamp assembly
3. Front room lamp
AA"4. Sunvisor holder5. Sunvisor assembly
DFront floor console assembly
(Refer to P.52A-10.)
AB"6. Headlining
Section A – A
Front pillar trim
A
AFront pillar trim
Instrument
panel

INTERIOR -Seat52A-22
REMOVAL SERVICE POINT
AA"REMOVAL OF HEADREST GUIDE
REAR SEAT
REMOVAL AND INSTALLATION
12
3
22±4NSm
3
Disassembly steps
"BA1. Rear seat cushion assembly
"AA2. Rear seatback assembly3. Rear seat hook

INTERIOR -Seat52A-23
INSTALLATION SERVICE POINTS
"AAINSTALLATION OF REAR SEATBACK
ASSEMBLY/REAR SEATBACK SIDE ASSEMBLY
L.H., R.H.
Press the rear seatback assembly in the direction shown
in the illustration and fit the attachment wire into the hook
securely to install the rear seatback assembly.
"
BAINSTALLATION OF REAR SEAT CUSHION
ASSEMBLY
Fit the rear seat cushion into the rear seat hook securely.
Rear seat back
assembly
Attachment wire
Hook
Rear seat cushion
assembly
Rear seat
hook

INTERIOR -Seat52A-24
DISASSEMBLY AND REASSEMBLY
1
24
3
Removal steps
1. Rear seat cushion cover
2. Rear seat cushion pad3. Rear seatback cover
4. Rear seatback pad