2007 MITSUBISHI LANCER EVOLUTION rear

EXTERIOR -Side Air Dam, Molding and Garnish51-10
REMOVAL SERVICE POINTS
AA"ROOF DRIP MOLDING REMOVAL
Use the special tool to pry the molding from the rear of the
body for removal.
Caution
Do not use the deformed mold again.
AB"SIDE AIR DAM REMOVAL
1. Attach protection tape all the way along the edges of
the double-sided tape which is still adhering to the body.
2. Use a resin spatula to scrape off the double-sided tape.
3. Peel off the protection tape.
4. Wipe the body surface and clean it with a rag moistened
with isopropyl alcohol.
INSTALLATION SERVICE POINTS
"AASIDE AIR DAM INSTALLATION
Double-sided tape affixing to the side air dam (when
reusing)
1. Scrape off the double-sided tape with a resin spatula
or gasket scraper.
2. Wipe off the side air dam adhesion surface and clean
it with a shop towel moistened with isopropyl alcohol.
3. Affix the specified double sided tape to the side air dam.
(Refer to P.51-9.)
MB990449
Protection tape
Double-sided tape

EXTERIOR -Rear Spoiler51-12
REAR SPOILER
ADHESIVE
ApplicationBrand
Rear spoilerDouble-sided tape [15 mm width 1.2 mm thickness, 30 mm width 1.2 mm
thickness]
REAR SPOILER
REMOVAL AND INSTALLATION
1
12
3
2
5.2±0.2 N·m
5.2±0.2 N·m5.2±0.2 N·m
5.2±0.2 N·m
A A
B
B
Steel plate hook
2
Claw
2
3
3 3
Double-sided tape:
Generic products: A : 15mm width, 1.2mm thickness,
B : 30mm width, 1.2mm thickness Section A – A
Section B – BA
B
Removal steps
DTrunk lid bumper
(Refer to Group 42.)
1. Gasket
2. Cap
A
A""
AA3. Rear spoilerNOTE:
The removal and installation service points are the
same as SIDE AIR DAM , MOLDING AND GARNISH.
(Refer to P.51-10)

EXTERIOR -Windshield Wiper and Washer51-15
5.0±1.0 NSm
4
1 3
2
NOTE: Refer to P.51-19 for more information regarding removal and installation of rear washer nozzle.
5
Washer hose removal steps
DSplash shild (Refer to
GROUP 42 – Fender.)
DCowl side trim, front scuff plate, center
pillar trim, lower, rear scuff plate (Refer
to GROUP 52A – Trim.)
DRear seat (Refer to GROUP
52A – Seat.)
1. Washer hose
Windshield washer nozzle removal
steps
DConnection of washer hose
2. Windshield washer nozzleWasher tank and windshield washer
motor assembly removal steps
DRear end trim, trunk side trim (Refer
to GROUP 52A – Trim.)
DConnection of front washer hose
3. Washer tank assembly
4. Washer tank bracket
5. Washer motor
NOTE: Refer to GROUP 54A– Column Switch for
removal and installation of wiper washer switch.

EXTERIOR -Windshield Wiper and Washer51-19
WINDSHIELD WIPER AND WINDSHIELD WASHER
SWITCH AND WINDSHIELD INTERMITTENT WIPER
INTERVAL ADJUSTING KNOB CHECK

(1) Windshield wiper and washer switch, rear wiper and
washer switch.
Switch positionTerminal No.p
6789101167891011
OFF
Windshield wiper mist switch ON
Windshield intermittent wiper switch ON
Windshield low-speed wiper switch ON
Windshield high-speed wiper switch ON
Windshield washer switch ON
(2) Windshield intermittent wiper interval adjusting knob
Measure the resistance value at terminal numbers 3 and
6. The resistance value should rise smoothly from
approximately 0Ω(“FAST” position) to apporoximately
1kΩ(“SLOW” position).
WINDSHIELD INTERMITTENT WIPER INTERVAL
ADJUSTING KNOB CHECK

Measure the resistance value at terminal numbers 4 and
6. The resistance value should rise smoothly from
approximately 0 W (“FAST” position) to approximately 1 kW
(“SLOW” position).
NOTE
The windshield washer switch and windshield wiper switch
is integrated in the column-ECU, so can not be checked as
an individual part. However, its operation can be checked
by the input signal check. (GROUP 54B - Troubleshooting.)

52A-2
INTERIOR
CONTENTS
SPECIAL TOOL 3............................
INSTRUMENT PANEL* 3......................
FRONT FLOOR CONSOLE 10................
REAR FLOOR CONSOLE 12..................
TRIMS 15....................................
HEADLINING 17..............................SEAT 19.....................................
Front Seat 19..................................
Rear Seat 22..................................
SEAT BELT 25...............................
Front Seat Belt 25.............................
Rear Seat Belt 26..............................
WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
WARNING!
(1) Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to personal
injury or death to service personnel (from inadvertent firing of the air bag) or to the driver and passenger (from rendering
the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an authorized
MITSUBISHI dealer.
(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B - Supplemental
Restraint System (SRS) before beginning any service or maintenance of any component of the SRS or any SRS-related
component.
NOTE
The SRS includes the following components: SRS-ECU, SRS warning lamp, air bag module, clock spring and interconnecting
wiring. Other SRS-related components (that may have to be removed/installed in connection with SRS service or maintenance) are
indicated in the table of contents by an asterisk (*).

INTERIOR -Front Floor Console52A-10
FRONT FLOOR CONSOLE
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
Removal and Installation of Rear Foor Console
(Refer to P.52A - 12.)
6
4
7 13
2 8 5
1
11 <
L.H. DRIVE VEHICLE>
9
10
12
Removal steps
1. Console side cover
2. Shift lever knob
3. Front floor console assembly
4. Front floor console panel
5. Cigarette lighter
6. Ashtray7. Shift lever cover
8. Shift lever panel garnish
9. Front floor console
10. Harness
11. Console side cover bracket
12. Front floor console bracket

INTERIOR -Front Floor Console52A-11
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
Removal and Installation of Rear Floor Console
(Refer to P.52A-12.)

3
456
78
9
12
1012 11
Removal steps
1. Console side cover
2. Shift lever knob
3. Front floor console assembly
4. Front floor console panel
5. Cigarette lighter
6. Ashtray7. Shift lever cover
8. Shift lever panel garnish
9. Front floor console
10. Harness
11. Console side cover bracket
12. Front floor console bracket

INTERIOR -Rear Floor Console52A-12
REAR FLOOR CONSOLE
REMOVAL AND INSTALLATION
1
3 2
2

3
Removal steps
1. Console box mat
2. Rear console assembly
DRear seat cushion assembly
(Refer to P.52A-22.)
DFront scuff plate
(Refer to P.52A-15.)DRear scuff plate (Refer to P.52A-15.)
DCenter pillar trim, lower
(Refer to P.52A-15.)
DFloor carpet
3. Rear console bracket