2007 KIA CARNIVAL reverse

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.Ignition "OFF".
2. Disconnect the connector of mode control actuator.
3. Verify that the mode control actuator operates to the defrost mode when connecting 12V to the terminal 1 and
grounding terminal 2.
4. Verify that the mode control actuator operates to the vent mode when connecting in the reverse.
5.Check the voltage between terminals 3 and 4.
Door position Voltage (3- 4)Error detecting
Vent 0.4 ± 0.15VLow voltage :0.1V or less
Defrost 4.6 ± 0.15VHigh voltage :4.9V or more
REPLACEMENT
1.Disconnect the negative ( - ) battery terminal.
2. Remove the rear heater unit.
3. Disconnect the mode control actuator connector (A).
4. Loosen the mounting screws and then remove the mode control actuator (B).
5.Installation is the reverse order of removal.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
1.Remove the rear control panel(A) and then dissconnect the rear control panel connector(B).
2.Installation is the reverse order of removal.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
1.Disconnect the negative ( - ) battery terminal.
2. Remove the crush pad.(Refer to BD group)
3. Disconnect the connectors from the intake actuator, the blower motor and power mosfet.
4. Remove the cowl cross bar assembly.(Refer to BD group)
5. Remove the blower unit (A) from the heater unit after loosening a mounting bolt and 2 screws.
Make sure that there is no air leaking out of the blower and duct joints.
6. Installation is the reverse order of removal.

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.Connect the battery voltage and check the blower motor rotation.
2.If the blower motor voltage is not operated well, substitute with a known- good blower motor and check for proper
operation.
3. If the problem is corrected, replace the blower motor.
REPLACEMENT
1.Disconnect the negative ( - ) battery terminal.
2. Disconnect the connector (A) of the blower motor.
3.Remove the blower motor (A) after loosening the mounting screws.
4.Installation is the reverse order of removal.

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.There should be continuity between the NO.1 in the A and NO.10 in the B terminals when power and ground are
connected to the NO.7 and NO.13 in the A terminals. (Passenger compartment relay box)
2. There should be to no continuity btween the NO.1 in the A and NO.10 in the B terminals when power is
disconnected.
REAR BLOWER
1.There should be continuity between the NO.4in the A and NO.12n the B terminals when power and ground are
connected to the NO.2and NO.14in the A terminals. (Passenger compartment relay box)
2. There should be to no continuity btween the NO.4in the A and NO.12in the B terminals when power is
disconnected.
REPLACEMENT
1.Disconnect the negative ( - ) battery terminal.
2. Remove the crash pad center lower side cover. (Refer to BD group)
3. Loosen the relat box mounting nut, and then remove the relay box(A).
4.Install in the reverse order of removal.

4.Installation is the reverse order of removal.

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.Ignition "OFF"
2. Disconnect the intake actuator connector.
3. Verify that the actuator operates to the recirculation position when connecting 12V to the terminal 3 and grounding
terminal 4.
4. Verify that the intake actuator operates to the fresh position when connecting in the reverse.
5.If the intake actuator is not operated well, substitute with a known- good intake actuator and check for proper
operation.
6. If the problem is corrected, replace the intake actuator.
REPLACEMENT
1.Disconnect the negative ( - ) battery terminal.
2. Remove the glove box (Refer to BD group).
3. Disconnect the intake actuator connector.
4. Loosen the mounting screw and then remove the intake actuator (A) from the blower unit.
5.Installation is the reverse order of removal.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
1.Disconnect the negative ( - ) battery terminal.
2. Remove the center air vent. (Refer to BD group)
3. Remove the heater & A/C controller (A) after loosening 4 screws.
4.Remove the heater & A/C controller (A).
5.Installation is the reverse order of removal.