2007 KIA CARNIVAL wheel alignment

14.Pull out the joint(BJ) boot on the side of wheel into the transaxle direction.
Be careful not to damage the boot.
REASSEMBLY
1.Wrap tape around the drive shaft splines (UTJ side) to prevent damage to the boots.
2. Apply grease to the joint(BJ) boot on the side of wheel and install the boots.
3. Install the bands to both boots.
4.Using clamp, secure the boot bands.
Clearance (A) : 2.0 mm (0.079 in.) or less
5.To install the dynamic damper, keep the BJ shaft in a straight line and secure the dynamic damper with the
dynamic damper bands.
6. Install the UTJ boot bands and UTJ boot.
7. Using the alignment marks (D) made during disassembly as a guide, install the spider assembly (A) and snap ring
(B) on the driveshaft splines (C).

accelerating around a cornerSee DS group - driveshaft.
Front suspension noise - A squeak,
creak, or rattle noise - occurs mostly
over bumps or rough roads Steering components
Loose or bent front struts or shock
absorbers
Damaged spring or spring mounts
Damaged or worn arm bushings
Worn or damaged stabilizer bar
bushing or linksGo to detailed test A.
Groaning or grinding - noise from the
front strut, occurs when driving on
bumpy roads or turning the vehicle Uneven seating surface between the
insulator and panel by the burrs
around the strut insulator mounting
bolts and the insulator boltes
mounting holesRepair or install a new parts as
necessary.
Rear suspension noise - a squeak,
creak or rattle noise - occurs mostly
over bumps or rough roads Loose or bent rear shock absorbers
Damaged spring or spring mounts
Damaged or worn control arm
bushingsGo to detailed test B.
Shudder - occurs during acceleration
from a slow speed or stop Rear axle assembly mis - positioned
Damaged or worn front suspension
componentsCheck the axle mounts and rear
suspension for damage or wear.
Repair as necessary.
Check for a loose stabilizer bar,
damaged or loose strut/strut bushings
or loose or worn ball joints. Inspect
the steering linkage for wear or
damage. Repair or Install new
components as necessary.
Shimmy - most noticeable on
coast/deceleration - also hard steering
condition Excessive positive caster
Check the caster alignment angle.
Correct as necessary.
Tire noise - hum/moan at constant
speeds Abnormal wear patterns
Spin the tire and Check for tire wear.
Install a new tire as necessary.
Inspect for damaged/worn suspension
components. Perform wheel
alignment.
Tire noise - noise tone lowers as the
vehicle speed is lowered Out- of- balance tire
Balance the tire and road test. Install
a new tire as necessary.
Tire noise - ticking noise, change with
speed Nail puncture or stone in tire tread
Inspect the tire. Repair or replace as
necessary.
Wheel and tire - vibration and noise
concern is directly related to vehicle
speed and is not affected by
acceleration, coasting or decelerating Damaged or worn tire
Go to detailed test C.
Tire wobble or shudder - occurs at
lower speeds Damaged wheel bearings
Spin the tire and check for abnormal
wheel bearing play or roughness.
Adjust or Install new wheel bearings
as necessary.
See DS group - front/rear axle.
Damaged wheel Inspect the wheel for damage. Install
a new wheel as necessary.
Damaged or worn suspension
components Inspect the suspension components
for wear or damage. Repair as
necessary.

Loosen wheel nutsCheck the wheel nuts.
Tighten to specification.
Damaged or uneven tire wear Spin the tire and Check for abnormal
tire wear or damage. Install a new tire
as necessary.
Tire shimmy or shake - occurs at
lower speeds Wheel/tire out of balance
Uneven tire wear
Check for abnormal tire wear. Install a
new tire as necessary.
Excessive radial runout of wheel or
tire Perform a radial runout test of the
wheel and tire.
Install a new tire as necessary.
Worn or damaged wheel studs or
elongate stud holes Inspect the wheel studs and wheels.
Install new components as necessary.
Excessive lateral runout of the wheel
or tire Perform a lateral runout test of the
wheel and tire.
Check the wheel, tire and hub. Repair
or Install new components as
necessary.
Foreign materal between the brake
disc and hub. Clean the mounting surfaces of the
brake disc and hub.
See DS group - front/rear axle.
High speed shake or shimmy - occurs
at high speeds Excessive wheel hub runout
Damaged or worn tires
Damaged or worn wheel bearings
Worn or damaged suspension or
steering linkage
Brake disc or drum imbalanceGo to detailed test D.
Drift left or right Tires
Steering linkage
Alignment
Base brake systemGo to detailed test E.
Steering wheel Alignment
Steering linkage
Front lower arm ball jointGo to detailed test F.
Tracks incorrectly Rear suspension
CasterGo to detailed test G.
Rough ride Front strut and spring assembly
Rear shock absorber and spring
assemblyGo to detailed test H.
Excessive noise Front or rear stabilizer bar
components
Springs
Suspension components
Shock absorbersGo to detailed test I.
Incorrect tire wear Tire or unbalanced wheels
Tire inflation
Strut
AlignmentGo to detailed test J.
Vibration Wheel/tire
Front wheel driveshaft(s)
Steering system
Strut and spring assemblyGo to detailed test K.

Strut and spring assembly
Spring and strut mounting
Front lower arm ball joint
Front lower arm mounting bolt
bushing
Stabilizer bar bushings
Wheel hubs and bearing
Rear suspension arms and bushings
Vehicle leans Tire/wheel
Vehicle load
Suspension components
Incorrect ride heightInflate tires to specification.
Redistribute the load as necessary.
Visually inspect the suspention
system.
Correct the ride height as necessary.
Poor steering returnability High knuckle rotating torque
AlignmentGo to detailed test E.
DETAILED TEST A : FRONT SUSPENSION NOISE CONDITIONS DETAILS/RESULTS/ACTIONS
ROAD TEST THE VEHICLE
a.Test drive the vehicle.
b. During the road test, drive the vehicle over a rough road. Determine
from which area/component the noise is originating.
● Is there a squeak, creak or rattle noise ?
→ YES
Go to
→ NO
The suspension system is OK. Conduct a diagnosis on other suspect
systems.
INSPECT THE STEERING SYSTEM a.Check the steering system for wear or damage.
Perform a steering linkage test.
Inspect the tire wear pattern.
● Are the steering components worn or damaged ?
→ YES
Repair the steering system. Install new components as necessary. Test
the system for normal operation.
→ NO
Go to
FRONT SHOCK ABSORBER/STRUT CHECK a.Check the front shock absorbers/strut mounts for loose bolts or nuts.
b. Check the front shock absorbers/struts for damage. Perform a shock
absorber check.
● Are the front shock absorbers/struts loose or damaged ?
→ YES
Tighten to specifications if loose.
Install new front shock absorbers/struts if damaged. Test the system for
normal operation.
→ NO
Go to
CHECK THE FRONT SPRINGS Check the front spring and front spring mounts/brackets for wear or
damage

Dismount the tire and mount the wheel on a wheel balancer. Measure the
runout on both wheel flanges. Go to detailed test C
● Is the runout within specifications ?
→ YES
Locate and Mark the low spot on the wheel. Install the tire, matching the
high spot on the tire with the low spot on the wheel. Balance the assembly.
Test the system for normal operation. If the condition persists, Go to D8.
→ NO
Install a new wheel. Check the runout on the new wheel. If the new wheel
is within limits, locate and Mark the low spot. Install the tire, matching the
high spot on the tire with the low spot on the wheel. Balance the assembly.
Test the system for normal operation. If the condition persists, Go to D8.
CHECK FOR VIBRATION FROM THE FRONT OF THE VEHICLE Spin the front wheel and tire assemblies with a wheel balancer while the
vehicle is raised on a hoist. Feel for vibration in the front fender or while
seated in the vehicle.
● Is the vibration present ?
→ YES
Substitute known good wheel and tire assemblies as necessary.
Test the system for normal operation.
→ NO
Check the driveline components. Test the system for normal operation.
DETAILED TEST E : DRIFT LEFT OR RIGHT CONDITIONS DETAILS/RESULTS/ACTIONS
CHECK THE TIRES Inspect the tires for excessive wear or damage.
● Are the tires excessively worn or damaged ?
→ YES
Install new tires.
→ NO
Go to E2.
CHECK THE STEERING LINKAGE
a.Raise and support the vehicle.
b. Check the steering components for indications of excessive wear or
damage.
See ST group - specification.
● Is there an indication of excessive wear or damage ?
→ YES
Repair or Install new components as necessary.
→ NO
Go to
CHECK THE VEHICLE ALIGNMENT a.Place the vehicle on an alignment rack.

Check the vehicle alignmnt.
● Is the alignment within specification ?
→ YES
Go to
→ NO
Adjust the alignment as necessary.
See page SS - 69 (wheel alignment).
BRAKE DRAG DIAGNOSIS Apply the brakes while driving.
● Does drift or pull occur when the brakes are applied ?
→ YES
See BR group - specification.
→ NO
If the steering wheel is in the center, the vehicle is OK.
If the steering wheel is off- center, Go to Detailed Test F.
DETAILED TEST F : STEERING WHEEL OFF- CENTER CONDITIONS DETAILS/RESULTS/ACTIONS
CHECK THE CLEAR VISION Place the vehicle on an alignment rack.
● Is the clear vision within specification ?
→ YES
Go to F2.
→ NO
Adjust the clear vision to specification.
INSPECT THE STEERING COMPONENTS
a.Raise and support the vehicle.
b. Inspect the steering components for excessive wear or damage.
See ST group - specification.
● Are the steering components excessively worn or damaged ?
→ YES
Repair or Install new components as necessary.
→ NO
If it tracks correctly, vehicle is OK.
If it tracks incorrectly, Go to Detailed Test
DETAILED TEST G : TRACKS INCORRECTLY CONDITIONS DETAILS/RESULTS/ACTIONS
CHECK THE CASTER Place the vehicle on an alignment rack.
● Is the caster within specification ?
→ YES
Go to G2.

● Is the vibration present ?
→ YES
Go to K2.
→ NO
The vehicle is OK. Go to TROUBLESHOOTING.
INSPECT THE TIRES
a.Raise and support the vehicle with a frame contact hoist.
b. Inspect the tires for extreme wear or damage, cupping, or flat spots.
● Are the tires OK ?
→ YES
Go to
→ NO
Check the suspension components for misalignment, abnormal wear, or
damage that may have contributed to the tire wear.
Correct the suspension concerns and Install new tires.
INSPECT THE WHEEL BEARINGS Spin the tires by hand to check for wheel bearing rougness.
● Is the front wheel bearing OK ?
→ YES
Go to K4.
→ NO
Install new front wheel bearings as necessary.
See Ds group - front axle.
TIRE/WHEEL BALANCE Check the tire/wheel balance.
● Are the tires balanced ?
→ YES
Go to K5.
→ NO
Balance the tires and wheels as necessary.
MEASURE THE RUNOUTS For each wheel position measure, locate and mark the following items.
- High point of the tire/wheel assembly total radial runout
- High point of the wheel radial runout
- High point of the wheel lateral runout
● Are the runouts as specified ?
→ YES
Go to K7.
→ NO
Go to K6.
SUBSTITUTE THE WHEELS AND TIRE

Spring610.0~642.2
Yellow 1 point
GASOLINE Free height mm (in)
291.1(11.46)
Load(kg) I.D. Color623.6~653.0
White 2 point
y
594.2~623.6 White 1 point
WHEELS AND TIRES Items Specification
Tire Size 225/70 R16
235/60 R17
Wheel Size Steel
6.5J×16
Aluminium 6.5J×16
6.5J×17
Tire Pressure KPa (kg/cm², psi) y
Front Rear
225/70 R16 2.4(35)2.4(35)
235/60 R17 2.4(35)2.4(35)
WHEEL ALIGNMENT Items FrontRear
Camber 0° ± 30´- 6´ ± 30´
Caster to Ground
3°46´ ± 30´ -
to Body 4°40´ -
Toe- in mm(in) 0 ± 2(0 ± 0.0787)2.6 ± 2(0.1024 ± 0.0787)
King pin angle 12°27´±30´-
Tread mm(in) 1685(66.34)1685(66.34)
TIGHTENING TORQUE
FRONT SUSPENSION
Items Nmkgf.m lb- ft
Front strut assembly mounting nut(to body) 45 ~ 604.5 ~ 6.032.5 ~ 43.4
Front strut assembly self - locking nut 60 ~ 706 ~ 743.4 ~ 50.6
Front strut assembly mounting bolt(to knuckle) 100 ~ 12010 ~ 1272.3 ~ 86.8
Front lower arm ball joint mounting bolt(to knuckle) 90 ~ 1209 ~ 1265.1 ~ 86.8
Front lower arm bushing(A) mounting bolt(to subframe) 160 ~ 18016 ~ 18115.7 ~ 130.2
Front lower arm bushing(G) mounting bolt(to subframe) 160 ~ 18016 ~ 18115.7 ~ 130.2
Front stabilizer link self - locking nut 100 ~ 12010 ~ 1272.3 ~ 86.8
Front stabilizer bar bracket mounting bolt(to Subframe) 39 ~ 603.9 ~ 6.028.2 ~ 43.4
Wheel nut 90 ~ 1109 ~ 1165.1 ~ 79.5
REAR SUSPENSION Items Nmkgf.m lb- ft