2007 KIA CARNIVAL battery

8Manifold Absolute Pressure
Sensor signal input IG ON
Analog 3.9 ~ 4.1V
3.96V
Idle 0.8 ~ 1.6V1.31V
9 - yy y y
10 - yy y y
11 Reference voltage (+5V) IG OFF
DCMax. 0.5V
4.91V
IG ON 4.9 ~ 5.1V- 50mV
12 Battery voltage supply after
ignition switch IG OFF
DCMax. 0.5 V
13.87V
IG ON Battery Voltage- 125mV
13 Reference voltage (+5V) IG OFF
DCMax. 0.5V
4.89V
IG ON 4.9 ~ 5.1V- 70mV
14 Sensor ground IdleDCMax. 50 mV 19.77mV
15 Reference voltage (+5V) IG OFF
DCMax. 0.5V
4.91V
IG ON 4.9 ~ 5.1V- 50mV
16 Reference voltage (+5V) IG OFF
DCMax. 0.5V
4.91V
IG ON 4.9 ~ 5.1V- 50mV
17 Sensor ground IdleDCMax. 50 mV 21.1mV
18 Sensor ground IdleDCMax. 50 mV 20.87mV
19 Ignition Coil (Cylinder #6) control
output Idle
Pulse 1st Voltage:
200~400V 278V
ON Voltage: Max. 2V 1.97V
20 - yy y y
21 Crankshaft Position Sensor
[High] signal input Idle
SINE
WAVE Vp_p : Min.1.0V
41.6V
22 - yy y y
23 Sensor Shield IdleDCMax. 50 mV 21.41mV
24 Camshaft Position Sensor [Bank
2] signal input
Idle
Pulse Hi: Vcc
4.95V
Lo: Max . 0.5V - 10mV
25 Camshaft Position Sensor [Bank
1] signal input
Idle
Pulse Hi: Vcc
4.95V
Lo: Max . 0.5V - 10mV
26 - yy y y
27 - yy y y
28 Sensor ground IdleDCMax. 50 mV 20.73mV
29 Sensor ground IdleDCMax. 50 mV 21.9mV
30 Sensor ground IdleDCMax. 50 mV 20.16mV
31 Sensor ground IdleDCMax. 50 mV 20.63mV
32 Reference voltage (+5V) IG OFF
DCMax. 0.5V
4.91V
IG ON 4.9 ~ 5.1V- 50mV
33 Sensor ground IdleDCMax. 50 mV 22.52mV
34 Sensor ground IdleDCMax. 50 mV 20.99mV
35 Power ground IdleDCMax. 50 mV y
36 Power ground IdleDCMax. 50 mV y
37 Power ground IdleDCMax. 50 mV y

38Power ground IdleDCMax. 50 mV y
39 Power ground IdleDCMax. 50 mV y
40 Ignition Coil (Cylinder #4) control
output Idle
Pulse 1st Voltage:
2300~400V 294V
ON Voltage: Max. 2V 1.93V
41 Crankshaft Position Sensor [Low]
signal input Idle
SINE
WAVE Vp_p: Min.1.0V
8.24V
42 - yy y y
43 - yy y y
44 - yy y y
45 - yy y
46 - yy y y
47 - yy y y
48 Throttle Position Sensor #1
signal input C.T
Analog 0.25 ~ 0.9V
0.68V
W.O.T Min. 4.0V4.27V
49 Heated Oxygen Sensor [Bank 1 /
Sensor 1] signal input
Racing
DCRich: 0.6 ~ 1.0V
774mV
Lean: 0 ~ 0.4V 137mV
50 Heated Oxygen Sensor [Bank 1 /
Sensor 2] signal input
Racing
DCRich: 0.6 ~ 1.0V
y
Lean: 0 ~ 0.4V y
51 Heated Oxygen Sensor [Bank 2 /
Sensor 1] signal input
Racing
DCRich: 0.6 ~ 1.0V
705.2mV
Lean: 0 ~ 0.4V 82mV
52 Heated Oxygen Sensor [Bank 2 /
Sensor 2] signal input
Racing
DCRich: 0.6 ~ 1.0V
y
Lean: 0 ~ 0.4V y
53 Knock Sensor (KS) [Bank 2]
[High] signal input Knocking
Variable
Frequency - 0.3 ~ 0.3 V
y
Normal 0 Vy
54 Knock Sensor (KS) [Bank 2]
[Low] signal input Knocking
Variable
Frequency - 0.3 ~ 0.3 V
y
Normal 0 Vy
55 Knock Sensor (KS) [Bank 1]
[Low] signal input Knocking
Variable
Frequency - 0.3 ~ 0.3 V
y
Normal 0 Vy
56 Knock Sensor (KS) [Bank 1]
[High] signal input Knocking
Variable
Frequency - 0.3 ~ 0.3 V
y
Normal 0 Vy
57 Throttle Position Sensor #2
signal input C.T
Analog Min. 4.0V
4.23V
W.O.T 0.25 ~ 0.9V703mV
58 Sensor ground IdleDCMax. 50 mV 21.64mV
59 - yy y y
60 Ignition Coil (Cylinder #2) control
output Idle
Pulse 1st Voltage:
200~400V 305V
ON Voltage: Max. 2V 1.85V
61 CVVT Oil Control Valve [Bank 2]
control output
Idle
PulseBattery Voltage
14.45V
Max. 1.0V 50mV
62 CVVT Oil Control Valve [Bank 1]
control output
Idle
PulseBattery Voltage
14.47V
Max. 1.0V 75mV
Injector (Cylinder #2) control Battery Voltage
14.06V

63Injector (Cylinder #2) control
output
Idle
PulseBattery Voltage
14.06V
Max. 1.0V 44.2mV
64 Injector (Cylinder #3) control
output
Idle
PulseBattery Voltage
14V
Max. 1.0V 38.31mV
65 - yy y y
66 - yy y y
67 Heated Oxygen Sensor [Bank 2 /
Sensor 1] Heater control output
Engine Run
PulseHi: Battery Voltage
14.07V
Lo: Max. 1.0V 275mV
68 Injector (Cylinder #4) control
output
Idle
PulseHi: Battery Voltage
13.96V
Lo: Max. 1.0V 55.71mV
69 Injector (Cylinder #5) control
output
Idle
PulseHi: Battery Voltage
14V
Lo: Max. 1.0V 40.82mV
70 Heated Oxygen Sensor [Bank 1 /
Sensor 1] Heater control output
Engine Run
PulseHi: Battery Voltage
14.07V
Lo: Max. 1.0V 275mV
71 Injector (Cylinder #6) control
output
Idle
PulseHi: Battery Voltage
13.95mV
Lo: Max. 1.0V 55.77mV
72 Injector (Cylinder #1) control
output
Idle
PulseHi: Battery Voltage
14.07V
Lo: Max. 1.0V 56.7mV
73 Heated Oxygen Sensor [Bank 2 /
Sensor 2] Heater control output
Engine Run
PulseHi: Battery Voltage
13.87V
Lo: Max. 1.0V 275mV
74 Heated Oxygen Sensor [Bank 1 /
Sensor 2] Heater control output
Engine Run
PulseHi: Battery Voltage
14.07V
Lo: Max. 1.0V 275mV
75 - yy y y
76 Battery Power AlwaysDCBattery Voltage
12.39V
1.0 mA or below 1.5 mA 0.34mA
77 Ignition Coil (Cylinder #3) control
output Idle
Pulse 1st Voltage:
200~400V 289V
ON Voltage: Max. 2V 1.87V
78 Ignition Coil (Cylinder #5) control
output Idle
Pulse 1st Voltage:
200~400V 279V
ON Voltage: Max. 2V 1.93V
79 Ignition Coil (Cylinder #1) control
output Idle
Pulse 1st Voltage:
200~400V 269V
ON Voltage: Max. 2V 1.91V
80 - yy y y

32ND SOLENOID(SCSV C)
Solenoid valve driver for 5sec.3. P range
4. Vehicle speed 0km/h
5. Engine stop
6. No failure
7. TPS < 1V
4
OD SOLENOID(SCSV D)
5 TORQUE CONVERTER SOLENOID VALVE
6 A/T CONTROL RELAY OFF for 3 sec. -
7 INTELLIGENT SHIFT PROHIBIT Prohibit until IG off -
8 CLEAR LEARNING VALUE --
ROAD TEST
No.Condition OperationJudgment value Check item
1 Ignition switch : OFF
Ignition switch
(1) ON Battery voltage (mV)
Control relay
2 a.
Ignition switch :
ON
b. Engine : Stopped
c. Selector lever
position : P Selector lever position
(1) P, (2) R, (3) N, (4) D
(1) P, (2) R, (3) N, (4)
DTransaxle range switch
Accelerator pedal
(1) Released
(2) Half depressed
(3) Depressed (1) 400~1,000 mV
(2)Gradually rises
from (1)
(3) 4,500~5,000 mVThrottle position sensor
Brake pedal
(1) Depressed
(2) Released (1) ON
(2) OFF
Brake switch
3 a.
Ignition switch : ST
b. Engine : Stopped Starting test with lever P or
N range
Starting should be
possibleStarting possible or
impossible
4 Warming up
Drive for 15 minutes or
more so that the automatic
fluid temperature becomes
70~90°C Gradually rises to
70~90°C
Oil temperature sensor
5 a.
Engine : Idling
b. Selector lever
position : N A/C switch
(1) ON
(2) OFF
(1) ON
(2) OFF
Triple pressure switch
Accelerator pedal
(1) Released
(2) Half depressed (1) ON
(2) OFF
Idle position switch
(1) 600~900 rpm
(2) Gradually rises
from (1)
(1) Data changes Communication with
engine - ECU
Selector lever position
(1) N→D
(2) N→R Should be no
abnormal shifting
shocks
Time lag should be
within 2 secondsMalfunction when starting
Selector lever position
: N (Carry out on a
flat and straight road) Selector lever position and
vehicle speed
a. Idling in 1st gear
(Vehicle stopped)
b. Driving at constant
speed of 20 km/h in 1st
gear (2) 1st, (4) 3rd, (3)
2nd, (5) 4th
Shift condition
(2) 0%, (4) 100%, (3)
100%, (5) 100% Low and reverse solenoid
valve
(2) 0%, (4) 0%, (3)
0% Underdrive solenoid valve

2007 > 2.7L V6 GASOLINE >
REMOVAL
a.Use a cover not to damage the vehicle surface.
b. Disconnect connectors carefully not to be damaged.
a.Mark wires or hoses for identification not to be confused.
1. Remove the battery (A).
2.After disconnecting the AFS connector(A) and removing the alr cleaner upper body(B) taka the air cleaner filter out
of the air cleaner under body.
3.Remove the air cleaner assembly (B) by removing the two mounting bolts(A).
4.Remove the battery tray (B) by removing the four mounting bolts (A).

29.Lifting the vehicle up and lowering the jack slowly, remove the transaxle assembly.
INSTALLATION
Installation is in the reverse order of removal.
Perform the following :
a. Adjust the shift cable.
b. Refill the transaxle with fluid.
c. Refill the radiator with engine coolant.
d. Bleed air from the cooling system with the heater valve open.
e. Clean the battery posts and cable terminals with sandpaper, assemble them, and apply grease to prevent
corrosion.
1. Lowering the vehicle or lifting up a jack, install the transaxle assembly.
2. Tighten the transaxle lower mounting bolts (B- 4EA).
TORQUE:
65~85 Nm(6.5~8.5 kgf.m, 47.0~61.5 lb - ft)
3. Install the drive plate bolts (A) by turning the timing gear.
TORQUE:
46~53 Nm(4.6~5.3 kgf.m, 33.3~38.3 lb - ft)
4.After removing a jack, insert the drive shafts. (see DS group)
5. Install the sub frame. (see SS group).
6. Tighten the roll stopper mounting bolts.
TORQUE:
90~110 Nm(9~11 kgf.m, 65.1~79.5 lb - ft)
7. Connect the lower arm, the tie rod end ball joint, the stabilizer bar link to the front knuckle. (see SS group)

20.Install the solenoid valve connector (A).
21.Install the input speed sensor connector (A).
22.Install the output speed sensor connector (A).
23.Install the vehicle speed sensor connector (A).
24.Install the battery tray (B) by removing the four mounting bolts (A).

25.Install the air cleaner assembly (B) by tightening the two mounting bolts (A).
26.Reassemble the air cleaner filter, install the air cleaner upper body (B) and connect the air flow sensor connector
(A).
27.Install the battery (A).
28.Refill the transaxle fluid. (see 'Service adjustment procedure')
29. Refill the power steering fluid. (see 'ST' group)