2006 LAND ROVER FRELANDER 2 climate control

Publi s hed: 11-May-2011
Climate Control - Air Conditioning (A/C) Pressure Transducer
Removal and Inst all ati on
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
Remove t he plenum chamber.
Refer t o: Plenum Chamber (412-01 Cl imat e Control, Removal and
Inst all at ion).
1. 2.
CAUTIONS: Ext reme cl eanli ness must be exerci sed when
handl ing t hese components . Make s ure that all openings are sealed. Us e new
blanking caps.
• NOTE: Us e an addit ional wrench t o prevent the
component from rot at ing.
T orque: 8 Nm 2.
Installation To i nst all , revers e t he removal procedure.
1.

Publi s hed: 11-May-2011
Climate Control - Temperature Blend Door Actuator LHRHD AWD
Removal and Inst all ati on
Removal
Remove t he glove compartment .
Refer t o: Glove Compart ment (501-12 Ins trument Panel andConsol e, Removal and Ins t al lat ion).
1.
2.
3.
Installation
To i nst all , revers e t he removal procedure.1.
If a new component has been ins t al led, configure usi ng Land Roverapproved diagnos t ic equipment .2.

Publi s hed: 11-May-2011
Climate Control - Temperature Blend Door Actuator LHLHD AWD
Removal and Inst all ati on
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
Make t he SRS s ys t em s afe.
Refer t o: Standard W orks hop Pract ices (100-00 General Informat ion,
Des cript ion and Operat ion).
1.
Remove t he s teeri ng col umn.
Refer t o: Steeri ng Column (211-04 St eering Col umn, Removal and
Inst all at ion).
2. Remove t he dri ver l ower ai r bag modul e s upport
bracket.
T orque: 7 Nm 3.
4.
Installation To i nst all , revers e t he removal procedure.
1.
If a new component has been ins t al led, configure usi ng Land Rover
approved diagnos t ic equipment .
2.

Publi s hed: 11-May-2011
Climate Control - Temperature Blend Door Actuator RHRHD AWD
Removal and Inst all ati on
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
Make t he SRS s ys t em s afe.
Refer t o: Standard W orks hop Pract ices (100-00 General Informat ion,
Des cript ion and Operat ion).
1.
Remove t he s teeri ng col umn.
Refer t o: Steeri ng Column (211-04 St eering Col umn, Removal and
Inst all at ion).
2. Remove t he dri ver l ower ai r bag modul e s upport
bracket.
T orque: 7 Nm 3.
4.

Publi s hed: 11-May-2011
Climate Control - Temperature Blend Door Actuator RHLHD AWD
Removal and Inst all ati on
Removal
Remove t he glove compartment .
Refer t o: Glove Compart ment (501-12 Ins trument Panel and
Consol e, Removal and Ins t al lat ion).
1. 2.
3.
Installation To i nst all , revers e t he removal procedure.
1.
If a new component has been ins t al led, configure usi ng Land Rover
approved diagnos t ic equipment .
2.

Publi s hed: 11-May-2011
Climate Control - Defrost Vent/Register Blend Door ActuatorLHD AWD
Removal and Inst all ati on
Removal
Remove t he glove compartment .
Refer t o: Glove Compart ment (501-12 Ins trument Panel and
Consol e, Removal and Ins t al lat ion).
1. 2.
Installation To i nst all , revers e t he removal procedure.
1.
If a new component has been ins t al led, configure usi ng Land Rover
approved diagnos t ic equipment .
2.

Publi s hed: 11-May-2011
Climate Control - Defrost Vent/Register Blend Door ActuatorRHD AWD
Removal and Inst all ati on
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
Make t he SRS s ys t em s afe.
Refer t o: Standard W orks hop Pract ices (100-00 General Informat ion,
Des cript ion and Operat ion).
1.
Remove t he s teeri ng col umn.
Refer t o: Steeri ng Column (211-04 St eering Col umn, Removal and
Inst all at ion).
2. Remove t he dri ver l ower ai r bag modul e s upport
bracket.
T orque: 7 Nm 3.
4.
Installation To i nst all , revers e t he removal procedure.
1.
If a new component has been ins t al led, configure usi ng Land Rover
approved diagnos t ic equipment .
2.

Publi s hed: 11-May-2011
Climate Control - Ambient Air Quality SensorLHD AWD
Removal and Inst all ati on
Removal
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
1.
Remove t he CJB.
Refer t o: Cent ral Junct ion Box (CJB) (418-00 Module Communi cat ionsNet work, Removal and Ins t allat ion).
2.
3.
Installation
To i nst all , revers e t he removal procedure.1.